G42 胶管、胶带、胶布 标准查询与下载

HG/T 3035-2011 吸水和排水用橡胶软管及软管组合件.规范

本标准规定了织物增强且内壁光滑的吸、排水用橡胶软管及软管组合件的最低要求。 本标准适用于软管使用环境温度为-25℃～＋70℃输送水温0℃～＋70℃范围内的，三种型别的软管和软管组合件。

Rubber hoses and hose assemblies for water suction and discharge.Specification

HG/T 2799-2011 吸引和低压排放石油液体用塑料软管及软管组合件 规范

警告—使用本标准的人员应熟悉正规实验室操作规程。本标准无意涉及因使用本标准可能出现的所有安全问题。制定安全和健康制度并确保符合国家法规是使用者的责任。 本标准规定了在-10℃～+45℃温度范围内排吸煤油、加热用油、柴油和润滑油用的两种型别聚合物增强热塑性塑料软管及软管组合件的要求。

Plastics hoses and hose assemblies for suction and low-pressure discharge of petroleum liquids.Specification

HG/T 3044-2011 通用织物增强的热塑性塑料排水软管.规范

警告—使用本标准的人员应熟悉正规实验室的操作规程。本标准无意涉及与其使用有关的任何安全问题。制定相应的安全和健康制度并确保符合国家法规条款是使用者的责任。 本标准规定了工作温度在-10℃～+60℃范围之间，最大工作压力为2.5 MPa的三种型别通用纺织物增强热塑性塑料排水软管的要求。 这些软管可用于输送通过使用添加剂使水的冰点降低到-10℃的水。 本标准不适用于下列软管： —输送饮用水软管； —洗衣机进水软管； —消防软管； —农业机械专业软管； —消费市场的园艺软管。

Thermoplastics hoses,textile-reinforced, for general-purpose water applications.Specification

HG/T 2300-2011 塑料软管.普通用途织物增强可折叠式输水软管.规范

本标准规定了四种型别的普通用途织物增强热塑性可折叠输水软管的要求，其使用温度范围为-10℃～55℃。 此类软管分为一下四个型别： —低压，设计用于最高工作压力：当23℃以下最大0.4MPa，当55℃以下最大0.2MPa； —中压，设计用于最高工作压力：当23℃以下最大0.7MPa，当55℃以下最大0.36MPa； —高压，设计用于最高工作压力：当23℃以下最大1.0MPa，当55℃以下最大0.51MPa； —超高压，设计用于最高工作压力：当23℃以下最大1.55MPa，当55℃以下最大0.70MPa。 本标准不适用于消防软管或输送饮用水用软管。

Plastic hose.General-purpose collapsible water hose, textile-reinforced.Specification

HG/T 3715-2011 双面多楔带

本标准规定了双面多楔带的产品结构、型号和标记、截面尺寸、要求、试验方法、检验规则及标志、标签、包装、运输和贮存。 本标准适用于汽车辅机和粮食机械双面传递动力用的双面多楔带。

Double-sided V-ribbed belts

ISO 10619-2:2011 橡胶,塑料软管和管材.曲挠性和刚性的测量.第2部分:低于环境温度的弯曲试验

Rubber and plastics hoses and tubing - Measurement of flexibility and stiffness - Part 2: Bending tests at sub-ambient temperatures

ISO 10619-1:2011 橡胶,塑料软管和管材.曲挠性和刚性的测量.第1部分:环境温度下的弯曲试验

This part of ISO 10619 specifies three methods for measuring the flexibility of rubber and plastics hoses and tubing (methods A1, B and C1), where the deformation of the hose or tubing is measured, and two methods for measuring the stiffness (methods A2 and C2) by measuring the force to bend the hose or tubing when rubber or plastics hoses or tubing are bent to a specific radius at ambient temperature. Methods A1 and A2 are suitable for rubber and plastics hoses and tubing with inside diameter of up to and including 80 mm. Method A1 allows the measurement of the flexibility of the hose or tubing by measuring the reduction in outside diameter when the hose is compressed between two plates. Method A2 provides a means of measuring the force required to reach a specific bend radius, when the hose or tubing is compressed, as between two plates. The test can be carried out at a specified internal pressure. Method B is suitable for rubber and plastics hoses and tubing with inside diameter of up to and including 100 mm, and provides a means of assessing the behaviour of the hose and tubing when bent around a mandrel. The final mandrel diameter used can be taken as the minimum bend radius of the hose or tubing. As this value is determined by the reduction of the outside diameter which can be used as a measure of the flexibility of the hose or tubing. The hose or tubing being tested can be unpressurized, pressurized or under vacuum and, if required, with the curvature or against the curvature of the hose or tubing, if such curvature is present. Methods C1 and C2 are suitable for rubber and plastics hoses and tubing with inside diameter of 100 mm and greater. Method C1 provides a means of determining the flexibility of the hose and tubing at the minimum bend radius. Method C2 provides a method of measuring the stiffness of the hose and tubing at the minimum bend radius.

Rubber and plastics hoses and tubing - Measurement of flexibility and stiffness - Part 1: Bending tests at ambient temperature

ISO 10619-3:2011 橡胶,塑料软管和管材.曲挠性和刚性的测量.第3部分:高温和低温下的弯曲试验

This part of ISO 10619 specifies a method for the determination of the bending characteristics of rubber and plastics hoses and tubing, including the force required for bending, over a range of temperatures from −60 ºC to +200 ºC. The nature of the apparatus, however, limits its applicability to rubber and plastics hoses and tubing of small internal diameter, i.e. up to 12,5 mm.

Rubber and plastics hoses and tubing - Measurement of flexibility and stiffness - Part 3: Bending tests at high and low temperatures

BS EN ISO 6224:2011 一般用途的输水用织物增强的热塑性软管.规范

Thermoplastics hoses, textile-reinforced, for general-purpose water applications. Specification

NF T47-265:2011 塑料软管.含水物质吸入和排放用螺旋热塑增强热塑软管规范.

Plastics hoses - Helical-thermoplastic-reinforced thermoplastics hoses for suction and discharge of aqueous materials - Specification.

NF T47-207/A1:2011 橡胶或塑料软管.提交膨胀率的测定.修改件1:对加压用液体的醇的定义.

Rubber or plastics hoses - Determination of volumetric expansion - Amendment 1 : deletion of alcohol as pressurizing fluid.

NF T47-201/A1:2011 橡胶和塑料软管,以及软管组件.软管尺寸规格和软管组件长度的测量方法.修改件1:可测外径部位的确认.

Rubber and plastics hoses and hose assemblies - Methods of measurement of the dimensions of hoses and the lengths of hose assemblies - Amendment 1 : clarification of position at which outside diameter is measured.

ISO 28017:2011 疏浚用金属或织物增强橡胶软管和软管总成规范

Rubber hoses and hose assemblies, wire or textile reinforced, for dredging applications - Specification

ISO 6801:1983/Amd 1:2011 橡胶或塑料软.管容积膨胀的测定.修改件1:作为加压流体的酒精的缺失

Rubber or plastics hoses - Determination of volumetric expansion - Amendment 1: Deletion of alcohol as pressurizing fluid

ISO 4671:2007/Amd 1:2011 橡胶和塑料软管和软管组件.软管尺寸规格和软管组件长度的测量方法.修改件1:测量外径的位置说明

Rubber and plastics hoses and hose assemblies - Methods of measurement of the dimensions of hoses and the lengths of hose assemblies - Amendment 1: Clarification of position at which outside diameter is measured

BS EN ISO 4641:2011 吸水和防水用橡胶软管和软管组件.规范

This International Standard specifies the minimum requirements for textile-reinforced, smooth-bore rubber water-suction and discharge hoses and hose assemblies. Three types of hoses and hose assemblies are specified according to their operating duty requirements, i.e. their ambient and water temperature ranges: -- ambient temperatures: −25 °C to +70 °C; -- water temperatures during operation: 0 °C to +70 °C.

Rubber hoses and hose assemblies for water suction and discharge. Specification

NF T47-258:2011 吸水排水橡胶管及管配件规范.

Rubber hoses and hose assemblies for water suction and discharge - Specification.

NF T47-251-1/A1:2011 橡胶塑料管及管配件的防爆及爆破压力与设计工作压力的比值.修改件1:整个文件中采用最大工作压力代替设计工作压力.

Rubber and plastics hoses and hose assemblies - Ratios of proof and burst pressure to design working pressure - Amendment 1 : replacement of "design working pressure by "maximum working pressure" throughout tex.

DIN EN 12115:2011 液体或气体化学药品用橡胶和热塑软管和软管组件.规范;德文版本EN 12115-2011

This European Standard specifies requirements for two types of hose assemblies (Types D and SD) with hoses made of rubber or thermoplastics and hose fittings made of metal designed to convey liquid or gaseous substances, hereinafter termed the "chemicals conveyed". The hose assemblies are intended for use with chemicals conveyed in the temperature range of -20 °C to +65 °C at a working pressure ≤ 10 bar.

Rubber and thermoplastics hoses and hose assemblies for liquid or gaseous chemicals - Specification; German version EN 12115:2011

JIS K 6351 AMD 1:2011 气体用金属线增强橡胶软管和软管配件(修改件1)

Wire reinforced rubber hoses and hose assemblies for gas (Amendment 1)