G42 胶管、胶带、胶布 标准查询与下载

JIS K 6351 AMD 1:2011 气体用金属线增强橡胶软管和软管配件(修改件1)

Wire reinforced rubber hoses and hose assemblies for gas (Amendment 1)

BS ISO 4081:2011 内燃机用制冷系统用橡胶软管和管件.规格

Rubber hoses and tubing for cooling systems for internal-combustion engines. Specification

HG/T 2819-2010 联组窄V带

本标准规定了联组窄V带的产品分类、结构、技术要求、试验方法、检验规则及标志、包装、贮存和运输。 本标准适用于高速及大功率的机械传动用联组窄V带，也适用于一般的动力传动用联组窄V带。

Joined narrow V-belts

DIN EN ISO 4671:2010 橡胶和塑料软管及软管组件.软管尺寸和软管组件长度的测量方法

Rubber and plastics hoses and hose assemblies - Methods of measurement of the dimensions of hoses and the lengths of hose assemblies (ISO 4671:2007); German version EN ISO 4671:2007

JIS K 6330-6:2010 橡胶和塑料软管的测试方法.第6部分:部件间附着力的测定

Rubber and plastics hoses -- Part 6: Determination of adhesion between components

ISO 4641:2010 给排水用橡胶软管和软管组件.规格

Rubber hoses and hose assemblies for water suction and discharge - Specification

DIN EN 13765:2010 烃类,溶剂和化学品输送用热塑性多层(非硫化)软管和软管组件.规范.德文版本EN 13765-2010

Thermoplastic multi-layer (non-vulcanized) hoses and hose assemblies for the transfer of hydrocarbons, solvents and chemicals - Specification; German version EN 13765:2010

KS M ISO 6807:2010 旋转式钻进和振动设施用橡胶软管和软管组件.规范

이 표준은 82 ℃의 최대 온도까지 물이나 기름을 함유한 진흙(water-based and

Rubber hoses and hose assemblies for rotary drilling and vibration applications-Specification

BS EN ISO 4023:2009 蒸汽用橡胶软管和软管组件.试验方法

WARNING — Persons using this International Standard should be familiar with normal laboratory practice. This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user to establish appropriate health and safety practices and to ensure compliance with any national regulatory conditions. All necessary safety devices shall be provided to ensure safe working conditions for the operators. This International Standard specifies test methods in which a rubber hose test piece or hose assembly is exposed to saturated steam, thus simulating service conditions. Four methods are specified, namely: - method A: vertical rack method; - method B: horizontal rack method; - method C: flexing test, vertical arrangement; - method D: flexing test, horizontal arrangement.

Rubber hoses and hose assemblies for steam - Test methods

BS ISO 8789:2009 机动车辆运送石油液化气用橡胶软管和软管组件.规范

Rubber hoses and hose assemblies for liquefied petroleum gas in motor vehicles - Specification

NF T47-250:2010 烃类,溶剂和化学制品输送用热塑性多层(未硫化)软管和软管组件.规范

Thermoplastic multi-layer (non-vulcanized) hoses and hose assemblies for the transfer of hydrocarbons, solvents and chemicals - Specification.

DIN EN ISO 4080:2010 橡胶和塑料软管及软管组件.透气性的测定

This International Standard specifies three methods for the determination of the volume of gas diffusing through a rubber or plastics hose or length of tubing in a specified time. Method 1: For determining the permeability of the complete hose or length of tubing, excluding endfittings, to the test gas. The permeability is calculated with respect to the length of the hose or tubing. Method 2: For determining the permeability at the hose/fitting interface. This method is used when determining the permeability characteristics of hoses with an unpricked cover, when the gas usually issues from the textile reinforcement at the cut ends. The permeability is calculated with respect to the length of the hose. Method 3: For determining precisely the permeability of a hose or hose assembly to the test gas. The permeability is calculated with respect to the surface area of the hose lining.

Rubber and plastics hoses and hose assemblies - Determination of permeability to gas (ISO 4080:2009); German version EN ISO 4080:2009

DIN EN ISO 8031:2010 橡胶和塑料软管和软管组件.电阻率和电导率的测定(ISO 8031-2009).德文版本EN ISO 8031-2009

This International Standard specifies electrical test methods for rubber and plastics hoses, tubing and hose assemblies to determine the resistance of conductive, antistatic and non-conductive hoses and the electrical continuity or discontinuity between metal end fittings. All the test methods described for rubber hoses in this International Standard can also be applied to plastics hoses.

Rubber and plastics hoses and hose assemblies - Determination of electrical resistance and conductivity (ISO 8031:2009); German version EN ISO 8031:2009

DIN EN ISO 2398:2010 织物增强的压缩空气用橡胶软管.规范(ISO 2398-2006).德文版本EN ISO 2398-2008

This International Standard specifies the requirements for three types, three classes and two categories of textile-reinforced rubber hose for compressed air, up to a maximum working pressure of 25 bar with an operating-temperature range of -40 ?C to +70 ?C, depending on the type and category.

Rubber hoses, textile-reinforced, for compressed air - Specification (ISO 2398:2006); German version EN ISO 2398:2008

DIN EN ISO 4023:2010 蒸汽用橡胶软管.试验方法(ISO 4023-2009).德文版本EN ISO 4023-2009

This International Standard specifies test methods in which the rubber hose test piece and/or hose assembly is exposed to saturated steam, so simulating service conditions. Four methods are specified, namely: Method A: Vertical rack method Method B: Horizontal rack method Method C: Flexing test, vertical arrangement Method D: Flexing test, horizontal arrangement.

Rubber hoses and hose assemblies for steam - Test methods (ISO 4023:2009); German version EN ISO 4023:2009

ISO 11237:2010 橡胶软管和软管组件.油基或水基流体用的金属丝编织增强压实型.规范

This International Standard specifies requirements for five types of compact, wire-braid-reinforced hose and hose assembly of nominal size from 5 to 31,5. They are suitable for use with water-based hydraulic fluids HFC, HFAE, HFAS and HFB as defined in ISO 6743-4 at temperatures ranging from −40 °Cto +100 °C.

Rubber hoses and hose assemblies - Compact wire-braid-reinforced hydraulic types for oil-based or water-based fluids - Specification

DIN EN ISO 1403:2010 一般用途的输水用织物增强橡胶软管.规范(ISO 1403-2005).德文版本EN ISO 1403-2008

This International Standard specifies the requirements for three types of general-purpose textile-reinforced rubber water hose with an operating temperature range of -25 ?C to +70 ?C and a maximum working pressure of up to 25 bar. These hoses are not intended to be used for conveyance of potable (drinking) water, for washing-machine inlets, as firefighting hoses, for special agricultural machines or as collapsible water hoses. These hoses may be used with additives which lower the freezing point of water.

Rubber hoses, textile reinforced, for general-purpose water applications - Specification (ISO 1403:2005); German version EN ISO 1403:2008

DIN EN ISO 3861:2010 喷砂清理用橡胶软管.规范(ISO 3861-2005).德文版本 EN ISO 3861-2008

This International Standard specifies the requirements for rubber hoses for wet and dry sand and grit blasting, suitable for use up to a maximum working pressure of 6, 3 bar and over an operating temperature range of -25 ?C to +70 ?C.

Rubber hoses for sand and grit blasting - Specification (ISO 3861:2005); German version EN ISO 3861:2008

DIN EN ISO 1402:2010 橡胶和塑料软管和软管组合件.液压试验方法(ISO 1402-2009)德文版本 EN ISO 1402-2009

This International Standard specifies methods for the hydrostatic testing of rubber and plastics hoses and hose assemblies, including methods for the determination of dimensional stability.

Rubber and plastics hoses and hose assemblies - Hydrostatic testing (ISO 1402:2009); German version EN ISO 1402:2009

DIN EN ISO 6802:2010 钢丝增强的橡胶和塑料软管及软管组件.弯曲液压脉冲试验

This International Standard describes a pressure impulse test with flexing for wire-reinforced rubber and plastics hydraulic hoses and hose assemblies. The test is applicable to high-pressure hydraulic hoses and hose assemblies, which are subject to pulsating pressure in service. This International Standard describes two methods of flexing the hose or hose assembly. The actual pressure impulse test is described in ISO 6803.

Rubber and plastics hoses and hose assemblies with wire reinforcements - Hydraulic impulse test with flexing (ISO 6802:2005); German version EN ISO 6802:2008