G42 胶管、胶带、胶布 标准查询与下载

BS EN ISO 4080:2009 橡胶和塑料软管及软管组件.透气性的测定

This International Standard specifies three methods for the determination of the volume of gas diffusing through a rubber or plastics hose or length of tubing in a specified time. Method 1: For determining the permeability of the complete hose or length of tubing, excluding endfittings, to the test gas. The permeability is calculated with respect to the length of the hose or tubing. Method 2: For determining the permeability at the hose/fitting interface. This method is used when determining the permeability characteristics of hoses with an unpricked cover, when the gas usually issues from the textile reinforcement at the cut ends. The permeability is calculated with respect to the length of the hose. Method 3: For determining precisely the permeability of a hose or hose assembly to the test gas. The permeability is calculated with respect to the surface area of the hose lining. The methods are applicable only to gases which are insoluble in water. NOTE 1 Although the results are expressed in the same units for methods 1 and 2, the results obtained will not necessarily be comparable in the case of unpricked and pricked hoses intended for the same application as the test times specified are different and the permeability could therefore vary. NOTE 2 Method 3 is the preferred method.

Rubber and plastics hoses and hose assemblies - Determination of permeability to gas

ISO 1436:2009/Cor 1:2010 橡胶软管和软管组件.油基或水基流体用金属丝增强液压型.规范.技术勘误表1

Technical Corrigendum 1 to ISO 1436:2009 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 1, Hoses (rubber and plastics). Page 5, Table 3 In the first column (nominal size), change 6 to 6,3.

Rubber hoses and hose assemblies - Wire-braid-reinforced hydraulic types for oil-based or water-based fluids - Specification; Technical Corrigendum 1

DIN EN ISO 6803:2010 橡胶和塑料软管及软管组件.无弯曲液压压力脉冲试验(ISO 6803-2008).德文版本EN ISO 6803-2008

This International Standard describes two categories of hose impulse testing without flexing for rubber or plastic hose assemblies. Category 1 is high pressure testing for test pressures greater than 3 MPa and Category 2 is for test pressures from 1, 5 MPa through 3 MPa. The test procedure is applicable to hydraulic hose assemblies that are subject to pulsating pressures in service and are contained within the product requirements.

Rubber or plastics hoses and hose assemblies - Hydraulic-pressure impulse test without flexing (ISO 6803:2008); German version EN ISO 6803:2008

ASTM F2785-10 聚酰胺 12 气压力管,软管及配件的标准规范

1.1 This specification covers requirements and test methods for the characterization of polyamide 12 pipe, tubing, and fittings for use in fuel gas mains and services for direct burial and reliner applications. The pipe and fittings covered by this specification are intended for use in the distribution of natural gas. 1.1.1 This specification does not cover threaded pipe. Generic fusion guidelines are given in Appendix X1. Design considerations are discussed in Appendix X2. In-plant quality control programs are specified in Annex A1. 1.2 The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Note 18212;Pipe and fittings utilizing heat fusion joining techniques produced from compounds meeting the requirements of Group 3, Class 2, and Grade 3 (PA323 or PA11) are intended for use with pipe manufactured from compounds meeting the requirements of Group 3, class 2 and Grade 3. Pipe and fittings utilizing heat fusion joining techniques produced from compounds meeting the requirements of Group 4, Class 2 and Grade 3 (PA 423 or PA12) are intended for use with pipe manufactured from compounds meeting the requirements of Group 4, Class 2 and Grade 3. As per the recommendations of the respective resin manufacturers, no cross fusion between PA 323 (PA11) and PA 423 (PA12) compounds is permitted.

Standard Specification for Polyamide 12 Gas Pressure Pipe, Tubing, and Fittings

ASTM E2226-10e1 水龙带水柱适用性标准操作规程

This practice is intended to standardize the apparatus used and the method or pattern of application of a standard hose stream to building elements as one part of the assessment and fire resistance of building elements. This practice specifies the water pressure and duration of application of the hose stream to the test assembly. This practice is intended to be used only after a test assembly has completed a prescribed standard fire-resistance test. The practice exposes a test assembly to a standard hose stream under controlled laboratory conditions. Pass/fail criteria are defined in the appropriate fire test method. This exposure is not intended to replicate typical fire fighting operations or all applied or impact loads a system could be subjected to in field use and conditions. Any variation from tested conditions has the potential of substantially changing the performance characteristics determined by this practice.1.1 This practice is applicable to building elements required to be subjected to the impact, erosion, and cooling effects of a hose stream as part of a fire-test-response standard. Building elements include, but are not limited to, wall and partition assemblies, fire-resistive joint systems, and doors. 1.2 This practice shall register performance of the building element under specific hose stream conditions. It shall not imply that, either after exposure or under other conditions, the structural capability of the building element is intact or that the building element is suitable for use. 1.3 The result derived from this practice is one factor in assessing the integrity of building elements after fire exposure. The practice prescribes a standard hose stream exposure for comparing performance of building elements after fire exposure and evaluates various materials and construction techniques under common conditions. 1.4 Units8212;The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.5 The text of this standard references notes which provide explanatory material. These notes shall not be considered as requirements of the standard. 1.6 This fire standard cannot be used to provide quantitative measures. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Application of Hose Stream

ASTM E2226-10 软管流使用的标准实施规程

This practice is intended to standardize the apparatus used and the method or pattern of application of a standard hose stream to building elements as one part of the assessment and fire resistance rating of building elements. This practice specifies the water pressure and duration of exposure or application of the hose stream to the test assembly. This practice is intended to be used only after a test assembly has completed a prescribed standard fire-resistance test. The practice exposes a test assembly to a standard hose stream under controlled laboratory conditions. Pass/fail criteria are defined in the appropriate fire test method. This exposure is not intended to replicate typical fire fighting operations or all applied or impact loads a system could be subjected to in field use and conditions. Any variation from tested conditions has the potential of substantially changing the performance characteristics determined by this practice.1.1 This practice is applicable to building elements required to be subjected to the impact, erosion, and cooling effects of a hose stream as part of a fire-test-response standard. Building elements include, but are not limited to, wall and partition assemblies, fire-resistive joint systems, and doors. 1.2 This practice shall register performance of the building element under specific hose stream conditions. It shall not imply that, either after exposure or under other conditions, the structural capability of the building element is intact or that the building element is suitable for use. 1.3 The result derived from this practice is one factor in assessing the integrity of building elements after fire exposure. The practice prescribes a standard hose stream exposure for comparing performance of building elements after fire exposure and evaluates various materials and construction techniques under common conditions. 1.4 Units8212;The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.5 The text of this standard references notes which provide explanatory material. These notes shall not be considered as requirements of the standard. 1.6 This fire standard cannot be used to provide quantitative measures. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Application of Hose Stream

KS M ISO 18752:2009 橡胶软管和软管组件.金属丝或纺织物.水利用的单胎压力加强型.规范

이 표준은 유압용 선재 또는 섬유 보강된 공칭 크기 5부터 102까지 4가지 등급(grad

Rubber hoses and hose assemblies-Wire-or textile-reinforced single-pressure types for hydraulic applications-Specification

JIS Z 1541:2009 高位差压敏双面涂层胶粘带

This Standard specifies the high potential pressure sensitive adhesive double coated (hereafter referred to as "tapes"). which have high adhesive power ,excellent heat resistance, and of which a part of the load applied to the joint part, etc. can be borne.

High potential pressure sensitive adhesive double coated tapes

JIS Z 1901:2009 防蚀用聚氯乙烯压敏胶粘带

This Standard specifies the pressure sensitive adhesive polypropyl chloride tapes to be used mainly for the corrosion prevention of steel tubes,steel bars and other metal bodies(herrafter referred to as "tapes").

Pressure sensitive adhesive polyvinyl chloride tapes for corrosion protection

HG/T 2581.1-2009 橡胶或塑料涂覆织物.耐撕裂性能的测定.第1部分:恒速撕裂法

警告：使用本标准的人员应有正规实验室工作的实践经验。本标准并未指出所有可能的安全问题。使用者有责任采取适当的安全和健康措施，并保证符合国家有关规定条件。 本部分规定了四种用恒定速率撕裂的方法来测定橡胶或塑料涂覆织物的耐撕裂性能。 A：舌形试样撕裂法； B：裤形试样撕裂法； C：梯形试样撕裂法； D：损坏试样撕裂法。

Rubber-or plastics-coated fabrics.Determination of tear resistance.Part 1:Constant rate of tear methods

HG/T 2581.2-2009 橡胶或塑料涂覆织物.耐撕裂性能的测定.第2部分:冲击摆锤法

警告：使用本标准的人员应有正规实验室工作的实践经验。本标准并未指出所有可能的安全问题。使用者有责任采取适当的安全和健康措施，并保证符合国家有关规定条件。 本部分规定了涂覆织物撕裂性能的测定方法，该方法是通过在凹口试样上施加主动作用力来表征试样耐撕裂性能。 本试验可以在试样经标准环境调节或预先浸泡处理后进行，通过本试验获得的试验结果与恒速撕裂法获得的试验结果不具有可比性。

Rubber-or plastics-coated fabrics.Determination of tear resistance.Part 2:Ballistic pendulum method

HG/T 2809-2009 浮顶油罐软密封装置橡胶密封带

本标准规定了浮顶油罐软密封装置橡胶密封带的结构、尺寸及公差、要求、试验方法、检验规则和标志、包装、运输、贮存等。 本标准适用于织物两面涂覆耐原油及轻质油品(苯及芳香烃除外)的橡胶而制成的浮顶油罐软密封装置橡胶密封带。

Seal installation for oil storaged tank's.Rubber seal belt

HG/T 3048-2009 橡胶或塑料涂覆织物.耐组合剪切曲挠和磨擦性能的测定

警告：使用本标准的人员应有正规实验室工作的实践经验。本标准并未指出所有可能的安全问题。使用者有责任采取适当的安全和健康措施，并保证符合国家有关规定条件。 本标准规定了橡胶或塑料涂覆织物耐组合剪切曲挠和磨擦性能的两种评价方法。磨擦由通过施加压脚强迫产生(方法A)或通过试样面之间的简单接触产生(方法B)。 方法B(不施加压脚)适用于压脚会通过不需要的磨擦作用而损坏试样的所有情况下，例如，具有黏性表面的材料、在粗糙表面上的聚氨酯光亮涂层。 本试验可在交付的产品上进行，亦可在经过如浸湿或加速老化等预处理后的产品上进行。

Rubber-or plastics-coated fabrics.Determination of resistance to combined shear flexing and rubbing

HG/T 3036-2009 饱和蒸汽用橡胶软管及软管组合件.规范

本标准规定了对两个型别的软管及软管组合件的要求，最大工作压力为0.6MPa的低压软管及软管组合件和最大工作压力为1.8MPa的高压软管及软管组合件都由橡胶软管和金属接头组成，用于输送饱和蒸汽和冷凝水。 每个型别都分为外覆层耐油和外覆层不耐油两个等级。

Rubber hoses and hose assemblies for saturated steam.Specification

HG/T 3041-2009 油槽车输送燃油用橡胶软管和软管组合件

警告：使用本标准的人员应有正规实验室工作的实践经验。本标准并未指出所有可能的安全问题。使用者有责任采取适当的安全和健康措施，并保证符合国家有关规定条件。 本标准规定了两组最大工作压力为1.0MPa装、卸液体烃类燃油用橡胶软管和软管组合件。 这两类软管设计用于： a芳烃体积分数不超过50%、含氧化合物含量达到15%的燃油； b工作温度范围为-30℃～+70℃，静态贮存温度范围为-50℃～+70℃。 本标准不适用于LPG系统、航空燃油系统、燃油站系统或海上使用的软管和软管组合件。

Rubber hoses and hose assemblies for bulk fuel by truck.Specification

HG/T 3043-2009 农业喷雾用橡胶软管

本标准规定了工作温度范围-10℃～+60℃，供农业和(或)化肥制品加压喷雾用三种类型柔性橡胶软管的要求。

Rubber hoses for agricultural spraying

HG/T 2491-2009 汽车用输水橡胶软管和纯胶管

本标准规定了汽车用输水橡胶软管和纯胶管的规格尺寸、技术要求、试验方法和检验规则等。 本标准适用于汽车发动机冷却系统及取暖系统用输水软管。中、轻型车橡胶软管使用温度为-30℃～+110℃；轿车用橡胶软管使用温度为-40℃～+120℃。

Rubber hoses and tubing for transferring water in automobiles

NF T47-135:2009 橡胶和塑料软管和软管组件.电阻率和电导率的测定

Rubber and plastics hoses and hose assemblies - Determination of electrical resistance and conductivity.

NF T47-202:2009 橡胶和塑料软管及软管组件.水压试验

Rubber and plastics hoses and hose assemblies - Hydrostatic testing.

ISO 8789:2009 摩托车输送液化石油气用橡胶软管和软管组件.规范

Rubber hoses and hose assemblies for liquefied petroleum gas in motor vehicles - Specification