G42 胶管、胶带、胶布 标准查询与下载

NF T47-252:2009 织物增强的压缩空气用橡胶软管.规范

Rubber hoses, textile-reinforced, for compressed air - Specification.

ISO 8829-1:2009 航空航天.聚四氟乙烯(PTFE)内胎软管组件.第1部分:金属(不锈钢)编织

This part of ISO 8829 specifies test methods for flexible polytetrafluoroethylene (PTFE) inner tubes with metallic (stainless steel) braided hose and hose assemblies used in aircraft fluid systems, in the pressure and temperature ranges covered by pressure classes and temperature types, as specified in ISO 6771. If performance requirements are not defined in this part of ISO 8829, they are defined in the performance specification. This part of ISO 8829 is applicable when reference is made to it in a procurement specification or other definition document. NOTE Fluids used for the tests are listed in Annex A. The requirements for non-metallic braid hose assemblies are given in ISO 8829-2.

Aerospace - Test methods for polytetrafluoroethylene (PTFE) inner-tube hose assemblies - Part 1: Metallic (stainless steel) braid

BS EN ISO 6803:2008 橡胶或塑料软管及软管组件.无挠性液压脉冲试验

This International Standard describes hose impulse testing, without flexing, of rubber or plastics hydraulic hose assemblies at both high and low impulse pressures. The high-pressure testing is carried out at pressures greater than 3 MPa and the low-pressure testing at pressures from 1,5 MPa to 3 MPa. The test procedure is applicable to hydraulic hose assemblies that are subject to pulsating pressures in service which are included in the product requirements. NOTE Impulse test procedures with flexing can be found in ISO 6802, Rubber and plastics hoses and hose assemblies with wire reinforcements — Hydraulic impulse test with flexing.

Rubber or plastics hoses and hose assemblies - Hydraulic-pressure impulse test without flexing

KS M ISO 2321:2009 橡胶螺纹.试验方法

이 표준은 섬유와 접촉하는 실 고무의 특정한 기계적 특성뿐만 아니라 실 고무의 일반적인 물

KS M ISO 2321:2009

BS EN ISO 2398:2008 压缩空气用纺织物增强橡胶软管.规范

Rubber hoses, textile-reinforced for compressed air - Specification

BS EN ISO 3861:2008 沙子和喷钢砂处理用橡胶软管.规范

Rubber hoses for sand and grit blasting - Specification

BS EN ISO 4641:2008 抽水和放水用橡胶软管和软管组件.规范

Rubber hoses and hose assemblies for water suction and discharge - Specification

ASTM D3359-09e2 胶带试验用测定粘合性的标准试验方法

If a coating is to fulfill its function of protecting or decorating a substrate, it must adhere to it for the expected service life. Because the substrate and its surface preparation (or lack of it) have a drastic effect on the adhesion of coatings, a method to evaluate adhesion of a coating to different substrates or surface treatments, or of different coatings to the same substrate and treatment, is of considerable usefulness in the industry. The limitations of all adhesion methods and the specific limitation of this test method to lower levels of adhesion (see 1.3) should be recognized before using it. The intra- and inter-laboratory precision of this test method is similar to other widely-accepted tests for coated substrates (for example, Test Method D2370 and Test Method D4060), but this is partly the result of it being insensitive to all but large differences in adhesion. The limited scale of 0 to 5 was selected deliberately to avoid a false impression of being sensitive.1.1 These test methods cover procedures for assessing the adhesion of coating films to metallic substrates by applying and removing pressure-sensitive tape over cuts made in the film. Note 18212;This test method has been reported being used to measure adhesion of organic coatings on soft substrates (for example, wood and plastic). Issues with plastic substrates are noted in Appendix X1. A similar test method, ISO 2409, permits tests on soft substrates (for example, wood and plaster). Precision and bias data on the later is lacking. Test Methods D3359 was developed with metal as the substrate and, in the absence of supporting precision and bias data, is so limited. 1.2 Test Method A is primarily intended for use at job sites while Test Method B is more suitable for use in the laboratory. Also, Test Method B is not considered suitable for films thicker than 5 mils (125μm). Note 28212;Subject to agreement between the purchaser and the seller, Test Method B can be used for thicker films if wider spaced cuts are employed. 1.3 These test methods are used to establish whether the adhesion of a coating to a substrate is at a generally adequate level. They do not distinguish between higher levels of adhesion for which more sophisticated methods of measurement are required. Note 38212;It should be recognized that differences in adherability of the coating surface can affect the results obtained with coatings having the same inherent adhesion. 1.4 This test method is similar in content (but not technically equivalent) to ISO 2409. 1.5 In multicoat systems adhesion failure may occur between coats so that the adhesion of the coating system to the substrate is not determined. 1.6 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.7 This standard does not purport to address the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Methods for Measuring Adhesion by Tape Test

CGA E-1-2009 气焊,气割及相关工艺用焊接橡胶软管及软管接头标准

This standard provides specifications for multi-service rubber hose used for weldin,q, cuttin,q, andallied proc- esses. This standard also describes connections for regulator outlets, torches, and fitted hose for welding and cutting equipment. It provides the dimensions of components (threaded connector, tailpiece, and coupling nut) for 18 different connections (Connection No. 020 through Connection No. 037) that may be used to connect gas hoses with torches and regulator outlets. To promote safety and reliability in service, the performance requirements that shall be met by the completed assemblies at the time of manufacture or rebuilding are specified. This standard does not apply to liquefied petroleum (LP) .qas hose covered under NFPA 58, Liquefied Petro- leum Gas Code applicable to the propane industry [5]. This standard describes the performance requirements of the hose that is fitted on the tailpiece with a clamp or ferrule.

Standard for rubber welding hose and hose connections for gas welding, cutting, and allied processes

BS EN ISO 6802:2008 钢丝增强的橡胶和塑料软管及软管组件.弯曲液压脉冲试验

This International Standard describes a pressure impulse test with flexing for wire-reinforced rubber and plastics hydraulic hoses and hose assemblies. The test is applicable to high-pressure hydraulic hoses and hose assemblies, which are subject to pulsating pressure in service. This International Standard describes two methods of flexing the hose or hose assembly. The actual pressure impulse test is described in ISO 6803.

Rubber and plastics hoses and hose assemblies with wire reinforcements - Hydraulic impulse test with flexing

BS EN ISO 1403:2008 一般用途的输水用织物增强橡胶软管.规范

This International Standard specifies the requirements for three types of general-purpose textile-reinforced rubber water hose with an operating temperature range of −25 °C to +70 °C and a maximum working pressure of up to 25 bar. These hoses are not intended to be used for conveyance of potable (drinking) water, for washing-machine inlets, as firefighting hoses, for special agricultural machines or as collapsible water hoses. These hoses may be used with additives which lower the freezing point of water.

Rubber hoses, textile-reinforced, for general-purpose water applications - Specification

BS EN ISO 6224:2008 一般用途的输水用织物增强的热塑性软管.规范

This International Standard specifies the requirements for three types of general-purpose textile-reinforced thermoplastic water-discharge hose with an operating temperature range of ?10 °C to +60 °C and a maximum working pressure of 25 bar 1). NOTE At temperatures above 23 °C and particularly above 40 °C, the maximum working pressure will be reduced. These hoses are not intended to be used for conveyance of potable (drinking) water, for washing-machine inlets, as firefighting hoses, for special agricultural machines or as gardening hoses for the consumer market. These hoses may be used with additives which lower the freezing point of water to ?10 °C.

Thermoplastics hoses, textile-reinforced, for general-purpose water applications - Specification

NF T47-205:2008 橡胶和塑料软管.静态条件下耐臭氧性的评估

Rubber and plastics hoses - Assessment of ozone resistance under static conditions.

KS M ISO 2928:2008 25巴(2.5MPa)及以下的天然气和液相或气相液化石油气用橡胶软管和软管组件.规范

이 표준은 -50 ℃~+70 ℃의 온도 범위의 저온 호스(-LT 지정)용으로 설계되거나 또

Rubber hoses and hose assemblies for liquefied petroleum gas (LPG) in the liquid or gaseous phase and natural gas up to 25 bar(2.5 MPa)－Specification

KS M ISO 1307:2008 工业通用橡胶和塑料软管.孔直径和公差.长度公差

이 표준은 각 호스 크기별 허용되는 고무 및 플라스틱 호스의 크기와 최소 및 최대 안지름에

Rubber and plastics hoses－Hose sizes, minimum and maximum inside diameters, and tolerances on cut-to-length hoses

KS M ISO 7326:2008 橡胶和塑料软管.静态条件下的耐臭氧性试验的评定

이 표준은 호스 외면층의 오존에 대한 저항을 측정하는 5가지 방법에 대하여 규정한다.

Rubber and plastics hoses－Assessment of ozone resistance under static conditions

MT 668-2007 煤矿用钢丝绳芯阻燃输送带

Steel wire core flame retardant conveyor belt for coal mines

MT 830-2007 煤矿用织物叠层阻燃输送带

Fabric laminated flame retardant conveyor belt for coal mines

MT 374-2007 煤矿用阻燃三角带

Flame retardant triangle belt for coal mines

MT 914-2007 煤矿用织物整芯阻燃输送带

Coal mine fabric whole core flame retardant conveyor belt