G42 胶管、胶带、胶布 标准查询与下载

NF T47-286:2008 橡胶或塑料软管和软管组件.无屈挠液压脉冲试验

Rubber or plastics hoses and hose assemblies - Hydraulic-pressure impulse test without flexing.

KS M ISO 5771:2008 输送无水氨用橡胶软管和软管组件

이 표준은 -40 55 ∼ ℃의 대기 온도에서 액체 또는 기체의 형태로 된 암모니아를 수송

Rubber hose and hose assemblies for transferring anhydrous ammonia－Specification

KS M ISO 11424:2008 内燃机的空气的和真空系统用橡胶软管和空气管规范

이 표준은 내연기관에서 필요로 하는 다양한 공기 시스템과 진공 시스템에 사용되는 위한 가황

Rubber hoses and tubing for air and vacuum systems for internal-combustion engines－Specification

ISO 5771:2008 输送无水氨用橡胶软管和软管组件.规范

This International Standard specifies the minimum requirements for rubber hoses used for transferring ammonia, in liquid or in gaseous form, at ambient temperatures from 40 ℃ up to and including +55 ℃. It does not include specifications for end fittings, but is limited to the performance of the hoses and hose assemblies.

Rubber hoses and hose assemblies for transferring anhydrous ammonia - Specification

SANS 2398:2008 织物增强的压缩空气用橡胶软管.规范

Specifies requirements for three types, three classes and two categories of textile-reinforced rubber hose for compressed air, up to a maximum working pressure of 25 bar with an operating-temperature range of -40 degrees celcius to +70 degrees celcius, d

Rubber hoses, textile-reinforced, for compressed-air - Specification

KS M ISO 4080:2008 橡胶和塑料软管及软管组件.透气性测定

이 표준은 규정된 시간 동안 고무 및 플라스틱 호스의 벽을 통해 빠져나가는 기체의 부피를

Rubber and plastics hoses and hose assemblies－Determination of permeability to gas

KS M ISO 6806:2008 用于油燃烧器的软管和软管组件.规范

이 표준은 오일 버너용 고무 호스와 호스 어셈블리의 최소 요구사항을 규정한다.호스

Rubber hoses and hose assemblies for use in oil burners－Specification

KS M ISO 9691:2008 橡胶.管接头的环工艺推荐标准.缺陷的说明和分类

이 표준은 파이프용 고무 접합부 링에서 결함을 서술하고 분류한다.

Rubber－Recommendations for the workmanship of pipe joint rings－Description and classification of imperfections

KS M ISO 8031:2008 橡胶和塑料软管和软管组件.电阻的测定

이 표준은 고무 또는 플라스틱제의 호스와 호스 어셈블리에 대한 것으로 전도성, 대전 방지성

Rubber and plastics hoses and hose assemblies－Determination of electrical resistance

KS M ISO 6805:2008 井下采矿用的橡胶软管和软管组件.采煤用的钢丝加筋液压型

이 표준은, 유형 1 5 ∼ 에서는 -40∼+100 , ℃ 유형 6에서는 -40∼+121

Rubber hoses and hose assemblies for underground mining－Wire-reinforced hydraulic types for coal mining－Specification

NF T47-600:2008 橡胶和塑料软管和软管组件.词汇

Rubber and plastics hoses and hose assemblies - Vocabulary.

DIN EN 1829-2:2008 高压喷水机械.安全要求.第2部分:软管、软管线路和连接器

This European Standard applies to hoses, hose lines and connectors intended to be used with high-pressure water jet machines within the scope of prEN 1829-1. This European Standard deals with all significant hazards, hazardous situations and events relevant to the equipment in the scope, when it is used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer (see clause 4). This European Standard deals with safety requirements to minimise the significant hazards which can arise from assembling, operating and servicing of hoses, hose lines and connectors for use with high pressure water jet machines (see clause 5). NOTE I This European Standard does not cover leak shields since they are not part of a hose line. The hazard due to scalding from hot liquid or from irritation / burning of any added chemicals is not covered in this European Standard. This European Standard is not applicable to hoses, hose lines and their accessories, which are manufactured before the date of its publication as EN. NOTE 2 For products of similar application that are outside of the scope of this European Standard and for which there is no alternative document available the relevant Clauses of this European Standard may be used.

High-pressure water jet machines - Safety requirements - Part 2: Hoses, hose lines and connectors; English version of DIN EN 1829-2:2008-06

BS EN 1829-2:2008 高压喷水机器.安全要求.软管、软管管路和接头

This European Standard applies to hoses, hose lines and connectors intended to be used with high-pressure water jet machines within the scope of prEN 1829-1. This European Standard deals with all significant hazards, hazardous situations and events relevant to the equipment in the scope, when it is used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer (see clause 4). This European Standard deals with safety requirements to minimise the significant hazards which can arise from assembling, operating and servicing of hoses, hose lines and connectors for use with high pressure water jet machines (see clause 5). NOTE 1 This European Standard does not cover leak shields since they are not part of a hose line. The hazard due to scalding from hot liquid or from irritation / burning of any added chemicals is not covered in this European Standard. This European Standard is not applicable to hoses, hose lines and their accessories, which are manufactured before the date of its publication as EN. NOTE 2 For products of similar application that are outside of the scope of this European Standard and for which there is no alternative document available the relevant Clauses of this European Standard may be used.

High-pressure water jet machines — Safety requirements — Part 2: Hoses, hose lines and connectors

DIN 26054:2008 化学产品用非金属螺纹软管组件

Non-metallic corrugated hose assemblies for chemical products

HG/T 3038-2008 岸上排吸油橡胶软管

本标准规定了船只在码头一侧装卸运输在常温常压下为液体的石油基产品的橡胶软管的分类、性能要求和试验方法。 本标准适用于船只在码头一侧装卸运输在常温常压下为液体的石油基产品的橡胶软管。不适用以屈挠金属为内衬层而制成的软管和设计用于海上的软管。软管适合于-20℃～+80℃的温度范围内使用。

Rubber hoses.on-shore oil suction and discharge

HG/T 3038~3039-2008 岸上排吸油橡胶软管 船/码头输油用橡胶软管

Shore discharge oil suction rubber hose ship/dock rubber hose for oil delivery

HG/T 3039-2008 船/码头输油用橡胶软管

本标准规定了船对船和船对码头输送常温常压下为液体的石油基产品的橡胶软管的分类、性能要求和试验方法。 本标准适用于船对船和船对码头输送常温常压下为液体的石油基产品的橡胶软管。软管适合于-20℃～+80℃的温度范围内使用。

Rubber hoses.ship/dockside oil discharge

HG/T 2184-2008 通用输水织物增强橡胶软管

警告——使用本标准的人员应熟悉正规实验室操作规程。本标准无意涉及因使用本标准而可能出现的所有安全问题。制定安全和健康制度并确保符合国家法规是使用者的责任。 本标准规定了对三种型别适用温度范围为-25℃～+70℃、最大工作压力为2.5MPa的通用输水织物增强橡胶软管的要求。 这些软管不适用于输送饮用水、洗衣机进水和专用农业机械，也不可用作消防软管或可折叠式水管。 这些软管可用于输送降低水的冰点的添加剂。

Rubber hoses, textile-reinforced, for general-purpose water applications

HG/T 2192-2008 喷砂用橡胶软管.规范

警告：使用本标准的人员应熟悉正规实验室操作规程。本标准无意涉及因使用本标准而可能出现的所有安全问题。制定安全和健康制度并确保符合国家法规是使用者的责任。 本标准规定了最大工作压力为0.63MPa，工作温度范围为－25℃～＋70℃，适用于金属表面作风压喷砂除锈、打麻、工程施工中湿喷砂和干喷砂橡胶软管的要求。

Rubber hoses for sand and grit blasting. Specification

HG/T 3037-2008 计量分配燃油用橡胶和塑料软管及软管组合件

警告——使用本标准的人员应熟悉正规试验室操作规程。本标准无意涉及因使用本标准可能出现的所有安全问题。制定相应的安全和健康制度并确保符合国家法规是使用者的责任。 本标准规定了计量分配燃油系统中(包括含氧化燃油:最高可混溶15%的含氧化合物)二种类别的三种型号软管和软管组合件的技术要求。 软管组合件在两种条件下使用:温度在-30℃～+55℃之间的常温等级和-40℃～+55℃之间的低温等级，工作压力≤1.6MPa 。

Rubber and plastic hoses and hose assemblies for measured fuel dispensing