G42 胶管、胶带、胶布 标准查询与下载

KS M ISO 1823-1:2008 橡胶软管和软管组件.第1部分:海上石油的抽取和输送.规格

이 표준은 대기 온도와 대기압에서 액체로 존재하는 석유계 제품을 운송하는 선박의 부두에서

Rubber hoses and hose assemblies－Part 1：On-shore oil suction and discharge－Specification

KS M ISO 2929:2008 油槽车排吸油用橡胶软管和软管组件.规范

이 표준은 다음과 같이 10 bar(1.0 MPa)의 최대 사용 압력으로 액체 탄화수소 연

Rubber hoses and hose assemblies for bulk fuel delivery by truck－Specification

BS EN ISO 4671:2007+A1:2011 橡胶和塑料软管和软管总成.软管尺寸和软管总成长度的测量方法

Rubber and plastics hoses and hose assemblies. Methods of measurement of the dimensions of hoses and the lengths of hose assemblies

CGA P-27-2008 非绝缘不锈钢低温液货舱软管用推荐软管管理惯例

This standard provides industrywide procedures for the use and inspection of uninsulated cryogenic hose (also referred to as cryogenic hose or hose). It is a guide for cargo tank hose users when they establish inspection procedures. It contains acceptance criteria appropriate for use during product transfers and routine mainte- nance. It represents the best currently available industry practice, but does not cover every possible hose de- sign, installation, and lading. Each user can apply this standard to suit individual installation and conditions of service. Acceptance for continued service in accordance with this standard does not guarantee that a hose or coupling assembly is not dangerous or cannot fail. This standard does not apply to vacuum-insulated hose or composite hose.

Recommended hose management practice for uninsulated stainless steel cryogenic cargo tank hose

ISO 4671:2007 橡胶和塑料软管及软管组件.软管尺寸和软管组件长度的测量方法

This International Standard specifies methods of measuring the inside diameter, outside diameter (including diameter over reinforcement of hydraulic hoses), wall thickness, concentricity and lining and cover thickness of hoses, methods of measurement and identification of the lengths of hoses and hose assemblies, and a method of verifying the through-bore of hydraulic hose assemblies.

Rubber and plastics hoses and hose assemblies - Methods of measurement of the dimensions of hoses and the lengths of hose assemblies

HG/T 2703-2007 小功率梯形齿同步带

本标准规定了小功率传动用环状梯形齿同步带（简称同步带）的产品分类，结构和材料，标记、要求，试验方法、检验规则，标志、包装、运输和贮存。 本标准适用于轻负荷机械上传递动力的梯形环状同步带。

Synchronous belts for light duty power transmission

KS M ISO 1401:2007 农业喷雾机用橡胶软管

이 규격은 -10~+60 ℃의 온도 범위 내에서 비료나 농약을 압력 분무하기 위해 쓰이는

Rubber hoses for agricultural spraying

DLA MS16070 REV F (2)-2007 空勤人员用飞机安全带

The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST database at http://assist.daps.dla.mil/.

BELT, AIRCRAFT SAFETY, CREWMAN'S

NAVY QPL-81581-1 NOTICE 1-2007 氧气及空气的放气软管组件的一般规定

QPL-81581-1, which identified products qualified under the requirements specified in MIL-DTL-81581, has been transformed to an equivalent qualification data set (QDS).

HOSE ASSEMBLIES, BREATHING OXYGEN AND AIR, GENERAL SPECIFICATION FOR

DLA MIL-DTL-3992 F (1)-2007 空气和真空闸系统橡胶软管和软管组装

This specification covers the construction, performance, and quality requirements of hose and hose assembly, rubber, air and vacuum brake systems intended for use as flexible connections on automotive air and vacuum brake systems in a temperature range from -60°F to +200°F (-51.1°C to +93.3°C), inclusive (see 6.1).

HOSE AND HOSE ASSEMBLY, RUBBER, AIR AND VACUUM BRAKE, SYSTEMS

ARMY MIL-PRF-49450 B VALID NOTICE 1-2007 镍镉飞机接口接充电电池

MIL-PRF-49450B, dated 06 March 2002, has been reviewed and determined to be valid for use in acquisition.

BATTERY, RECHARGEABLE, NICKEL-CADMIUM, VENTED, AIRCRAFT

DLA MIL-DTL-26633 E-2007 氧,聚四氟乙烯用非导电软管组件

This specification covers one type of hose assembly, nonconductive, dolytetrafluoroethylene, oxygen having a nominal working pressure of 3,000 psig (206.84 bar) in the operating temperature range from -65°F to +160°F (-53.89°C to 71.11°C).

HOSE ASSEMBLY, NONCONDUCTIVE, POLYTETRAFLUOROETHYLENE, OXYGEN

CGA P-7-2007 二氧化碳冷却液的转移用海上储罐软管的再次合格鉴定用指南.第5版

The Compressed Gas Association has prepared this standard as a guide for cargo tank hose users in establishing their own hose requalification procedures and standards in carbon dioxide refrigerated liquid transfer service applications. This publication is primarily written for elastomer carbon dioxide hoses, but the general inspections may be applied to hoses for other commodities. It should be understood that this is a minimum standard and may not cover all circumstances for every hose installation and lading. Each user can expect to modify this minimum standard to suit the user's own installation and conditions of service. Acceptance for continued service in accordance with these limits does not guarantee that a hose or coupling assembly is not danger~us or without the possibility of impending failure. These procedures represent the best currently available industry practice. This standard is recommended as being limited in application to hose of the following characteristics: having an inner tube of natural or synthetic elastomer using reinforcement material consisting of a ply or plies of textile fabric or yarn and/or metal wire braid and enveloped with an outer protective cover; and internal diameters from 1/4 in to 4 in (6.4 mm to 102 mm) and maximum rated working pressures from over 125 psig (860 kPa) up to and including 500 psig (3450 kPa) See CGA G-6.6, Standard for Elastomer-Type Carbon Dioxide Bulk Transfer Hose, for additional information concerning construction of hoses to which this standard applies [5]. Standards for the requalification of Iow pressure hose having 125 psig (860 kPa) and lower maximum rated working pressures used in services such as the transfer of flammable liquids and combustible liquids should be obtained from the appropriate standards sources. In add tion, cryogenic liquids and certain compressed gases such as chlorine require the use of metal hose or hose with metal liners, and users should refer to the specified industry standards or to the manufacturers of such hose with regard to recommendations for reinspection and retesting procedures.

STANDARD FOR REQUALIFICATION OF CARGO TANK HOSE USED IN THE TRANSFER OF CARBON DIOXIDE REFRIGERATED LIQUID FIFTH EDITION

ASTM E2226-07 软管射流用标准实施规程

1.1 This practice is applicable to building elements required to be subjected to the impact, erosion, and cooling effects of a hose stream as part of a fire-test-response standard. Building elements include, but are not limited to, wall and partition assemblies, fire-resistive joint systems, and doors.1.2 This practice shall register performance of the building element under specific hose stream conditions. It shall not imply that, either after exposure or under other conditions, the structural capability of the building element is intact or that the building element is suitable for use.1.3 The result derived from this practice is one factor in assessing the integrity of building elements after fire exposure. The practice prescribes a standard hose stream exposure for comparing performance of building elements after fire exposure and evaluates various materials and construction techniques under common conditions.1.4 Units The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the practice. Within the text, the SI units are shown in brackets.1.5 The text of this standard references notes which provide explanatory material. These notes shall not be considered as requirements of the standard.1.6 This standard is used to measure and describe the response of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire risk assessment of the materials , products, or assemblies under actual fire conditions.1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Application of Hose Stream

DIN EN ISO 8033:2006 橡胶和塑料软管.元件间附着力的测定(ISO 8033:2006)

Adequate adhesion between the various components of a hose is essential if it is to perform satisfactorily in service. This International Standard specifies methods for the determination of the adhesion between lining and reinforcement, between cover and reinforcement, between reinforcement layers, between cover and outer lamination (thin layer of material outside the cover for protection) and between lining and inner lamination (thin layer of material inside the lining to reduce permeation of fluid into the lining). It covers all bore sizes and the following types of hose construction: — woven textile fabric; — braided textile fabric; — knitted textile fabric; — circular-woven textile fabric; — textile spiral; — textile cord; — wire braid; — wire spiral; — hoses containing a supporting helix.

Rubber and plastics hoses - Determination of adhesion between components (ISO 8033:2006); English version of DIN EN ISO 8033:2006-11

ISO 21012:2006 低温容器.软管

This International Standard gives design, construction, type and production testing, and marking requirements for non-insulated cryogenic flexible hoses used for the transfer of cryogenic fluids within the following range of operating conditions: - working temperature: from − 270 °C to − 65 °C; - nominal size (DN): from 10 to 100. End fittings for mounting of any couplings are within the scope of this International Standard, but the couplings are subject to other standards.

Cryogenic vessels - Hoses

ISO 2321:2006 橡胶线.试验方法

This International Standard specifies methods of test for determining general physical and mechanical properties of rubber threads, as well as specific mechanical properties of such threads in contact with fabrics. Owing to the comparatively small cross-section and the unusual conditions of service of this material, certain special methods have been developed. Some of the tests included in this International Standard may not be entirely suitable for threads made from certain synthetic rubbers (e.g. urethane rubber). These tests are intended for natural or synthetic polyisoprene rubbers. It is pointed out that comparisons may only be made on new rubber threads or on those with identical processing histories. In the interpretation of results from threads which have been subjected to spooling, fabrication or any other process, it should be borne in mind that the previous history is important, and what is known of this and of any relaxation treatments used shall be stated in the test report.

Rubber threads - Methods of test

ISO 7326:2006 橡胶和塑料软管.静态条件下评定耐臭氧性

This International Standard specifies five methods for determining the ozone resistance of the outer covers of hoses: ⎯ method 1, for bore sizes up to and including 25 mm, carried out on the hose itself; ⎯ method 2, for bore sizes greater than 25 mm, carried out on a test piece from the hose wall; ⎯ method 3, for bore sizes greater than 25 mm, carried out on a test piece from the cover; ⎯ method 4, for all bore sizes, carried out on the hose itself; ⎯ method 5, for all bore sizes, carried out on hoses that are expandable, for example textile-reinforced hoses. NOTE For hoses with built-in fittings from which it is not possible to take test pieces, the ozone resistance may be assessed on slabs in accordance with ISO 1431-1, using test sheets of the appropriate polymeric compound vulcanized to the same degree.

Rubber and plastics hoses - Assessment of ozone resistance under static conditions

ISO 1307:2006 橡胶和塑料软管.软管大小、最小和最大内径及长软管切割公差

This International Standard specifies the sizes of rubber and plastics hoses and the minimum and maximum inside diameters permitted for each hose size. For this purpose, hoses are divided into four types according to the process by which they are manufactured. The standard also specifies tolerances on cut-to-length rubber and plastics hoses for industrial and automotive applications. This standard is intended to be used with the relevant hoses product standard unless there is justification for using a different hose size or unless a hose size needs a different inside-diameter range for a particular application.

Rubber and plastics hoses - Hose sizes, minimum and maximum inside diameters, and tolerances on cut-to-length hoses

HG/T 3842-2006 消防用不可折叠型橡胶和塑料软管.第1部分:定位应急设施用轴卷半硬性软管

本标准规定了应急消防用轴卷半硬性软管的性能和试验。内径为19mm和25mm的软管预定最大工作压力为1.2MPa，内径为 33mm 的软管预定最大工作压力为0.7MPa 。 符合本标准的软管可用在远距离使用场地之间，例如在建筑物群或其他建筑工地中的固定的消防软管卷轴上。对于内径为19mm和25mm的软管，最小卷轴直径为200mm，对于内径为33mm的软 管，最小卷轴直径为280mm。 本标准仅适用于在温度范围为-20℃ ～+60 ℃的非腐蚀性环境条件下使用的软管。 在购货方需要时，可以提供低于-20℃（例如-30℃）下使用的软管。

Rubber and plastics hoses, non-collapsible, for fire-fighting service Part 1: Semi-rigid reel hose for fixed first-aid installations