G49 炭黑 标准查询与下载

ASTM D3265-05 炭黑的标准试验方法.着色强度

1.1 This test method covers the determination of the tint strength of carbon black relative to an industry tint reference black (ITRB).1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Carbon Black8212;Tint Strength

ASTM D4821-05 炭黑的标准指南.验证试验方法精确度和偏差

1.1 This guide covers a procedure for using ASTM Standard Reference Blacks (SRBs) to continuously monitor the precision of those carbon black test methods for which standard values have been established. It also offers guidelines for troubleshooting various test methods.1.2 This guide establishes the x-chart control limits to be used when continuously monitoring those tests listed in Section . Alternatively, these control limits may be used as a basis for comparison to testing precision computed within a laboratory.1.3 This guide uses statistical control chart methodology as discussed in STP-15-D to determine if a laboratory's test results differ significantly from the accepted values of the SRBs.1.4 This guide provides a statistical procedure for improving test reproducibility when a laboratory cannot physically calibrate its apparatus to obtain the standard values of the ASTM SRBs, within the ranges given in the precision statement of the test method.1.5 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Guide for Carbon Black8212;Validation of Test Method Precision and Bias

ASTM D2414-05 炭黑的标准试验方法.油吸收值

1.1 This test method covers the determination of the oil absorption number of carbon black.1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Carbon Black8212;Oil Absorption Number (OAN)

ASTM D6915-05b 炭黑的标准规程.标准参考炭黑的评价

1.1 This practice covers guidelines for the production and testing for uniformity of a set of carbon blacks to be used as Standard Reference Blacks (SRBs).1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Carbon Black8212;Evaluation of Standard Reference Blacks

ASTM D1765-05a 橡胶制品用炭黑的标准分类系统

1.1 This classification system covers the classification of rubber-grade carbon blacks by the use of a four-character nomenclature system. The first character gives some indication of the influence of the carbon black on the rate of cure of a typical rubber compound containing the black. The second character gives information on the average surface area of the carbon black. The last two characters are assigned arbitrarily.1.2 All rubber-grade carbon blacks for which a number is currently assigned at the time of publication of this classification system are listed in together with some of their typical properties. ASTM classification numbers ("N" or "S" designation) not listed in have either been withdrawn or are not currently assigned. The use of inactive or unassigned N or S designations is prohibited until such a time as the designation is officially reactivated or assigned by Subcommittee D24.411.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Classification System for Carbon Blacks Used in Rubber Products

ASTM D1765-05ae1 橡胶制品用炭黑的标准分类系统

1.1 This classification system covers the classification of rubber-grade carbon blacks by the use of a four-character nomenclature system. The first character gives some indication of the influence of the carbon black on the rate of cure of a typical rubber compound containing the black. The second character gives information on the average surface area of the carbon black. The last two characters are assigned arbitrarily.1.2 All rubber-grade carbon blacks for which a number is currently assigned at the time of publication of this classification system are listed in together with some of their typical properties. ASTM classification numbers ("N" or "S" designation) not listed in have either been withdrawn or are not currently assigned. The use of inactive or unassigned N or S designations is prohibited until such a time as the designation is officially reactivated or assigned by Subcommittee D24.411.3 si-value;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Classification System for Carbon Blacks Used in Rubber Products

ASTM D1765-05 橡胶制品用炭黑的标准分类系统

1.1 This classification system covers the classification of rubber-grade carbon blacks by the use of a four-character nomenclature system. The first character gives some indication of the influence of the carbon black on the rate of cure of a typical rubber compound containing the black. The second character gives information on the average surface area of the carbon black. The last two characters are assigned arbitrarily.1.2 All rubber-grade carbon blacks for which a number is currently assigned at the time of publication of this classification system are listed in together with some of their typical properties. ASTM classification numbers ("N" or "S" designation) not listed in have either been withdrawn or are not currently assigned. The use of inactive or unassigned N or S designations is prohibited until such a time as the designation is officially reactivated or assigned by Subcommittee D24.411.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Classification System for Carbon Blacks Used in Rubber Products

ASTM D1512-05 炭黑pH值的标准试验方法

The pH level of a carbon black is known to affect the vulcanization of some rubber compounds.1.1 These test methods, Test Method A-Boiling Slurry and Test Method B-Sonic Slurry, are used to indicate the pH of the carbon black surface by measuring the pH of water in contact with the carbon black. Note 1The pH of the carbon black is often used in this industry to indicate the relative acidity or alkalinity of carbon black and will be used in the remainder of these test methods to describe this property.Note 2Test Method A and Test Method B do not always give the same results.1.2 The values stated in SI units are to be regarded as the standard. The values in parentheses are for information only.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Methods for Carbon Black-pH Value

ASTM D1510-05a 炭黑的标准试验方法.碘吸收值

1.1 This test method covers the determination of the iodine adsorption number of carbon black.1.1.1 Procedure A is the original procedure for this determination.1.1.2 Procedure B specifies an increased sample mass of carbon black and volume of iodine solution (the ratio is the same as in Procedure A) which results in a simplified formula for the calculation of the iodine number.1.2 The iodine adsorption number of carbon black has been shown to decrease with sample aging. New SRB HT Iodine Standards have been produced that exhibit stable iodine number upon aging. These SRB HT Iodine Standards are recommended for daily monitoring (x-charts) of testing and for standardization of iodine testing (see Section 10) when target values cannot be obtained.1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Carbon Black8212;Iodine Adsorption Number

ASTM D1513-05(2012) 颗粒状炭黑倾注密度的标准试验方法

1.1 This test method covers the determination of the pour density of pelleted carbon blacks. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Carbon Black, Pelletedmdash;Pour Density

ASTM D1510-05 炭黑的标准试验方法.碘吸收值

1.1 This test method covers the determination of the iodine adsorption number of carbon black.1.1.1 Procedure A is the original procedure for this determination.1.1.2 Procedure B specifies an increased sample mass of carbon black and volume of iodine solution (the ratio is the same as in Procedure A) which results in a simplified formula for the calculation of the iodine number.1.2 si-value;1.3 The iodine adsorption number of carbon black has been shown to decrease with sample aging. New SRB HT Iodine Standards have been produced that exhibit stable iodine number upon aging. These SRB HT Iodine Standards are recommended for daily monitoring (x-charts) of testing and for standardization of iodine testing (see Section 10) when target values cannot be obtained.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Carbon Black8212;Iodine Adsorption Number

ASTM D1513-05e2 碳黑,球状8212;倾注密度的标准试验方法

Pour density is a function of the degree of compaction during pelletization. It is strongly influenced by and inversely proportional to structure (OAN). Pour density of carbon black is useful for estimating the weight-to-volume relationship for certain applications, such as automatic batch loading systems, and for estimating weights of bulk shipments. 1.1 This test method covers the determination of the pour density of pelleted carbon blacks. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Carbon Black, Pelleted&8212;Pour Density

ASTM D6086-05 炭黑的标准试验方法.有效容积(VV)

The void volume of a carbon black expressed in absolute terms, VV, is a carbon black property that reflects differences in structure for candidate carbon blacks. Structure is a generic term that is a function of the shape irregularity and deviation from sphericity of carbon black aggregates. The more that a carbon black resists compression by having substantial aggregate irregularity and non-sphericity, the greater the compressed volume and void volume. Structure is a property that influences the physical properties developed in carbon black compounds for use in tires, mechanical rubber goods, and other manufactured rubber products.1.1 This test method covers a procedure to measure a carbon black property called Void Volume. The void volume is obtained by measuring the compressed volume of a weighed sample contained in a cylindrical chamber when a specified compression force is applied by a movable piston with a displacement transducer on the piston mechanism.1.2 Void volume is an important carbon black property that relates to the compounded physical properties for carbon black-filled elastomers.1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Carbon Black8212;Void Volume (VV)

ASTM D1513-05 颗粒状炭黑的标准试验方法.倾注密度

Pour density is a function of the degree of compaction during pelletization. It is strongly influenced by and inversely proportional to structure (OAN). Pour density of carbon black is useful for estimating the weight-to-volume relationship for certain applications, such as automatic batch loading systems, and for estimating weights of bulk shipments. 1.1 This test method covers the determination of the pour density of pelleted carbon blacks.1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Carbon Black, Pelleted8212;Pour Density

ASTM D6915-05a 炭黑的标准规程.标准参考炭黑的评价

1.1 This practice covers guidelines for the production and testing for uniformity of a set of carbon blacks to be used as Standard Reference Blacks (SRBs).1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Carbon Black8212;Evaluation of Standard Reference Blacks

ASTM D5230-05 炭黑的标准试验方法.自动形成的单个颗粒硬度

Individual pellet hardness is related to several carbon black characteristics. Among these are mass strength and attrition. The subsequent level of dispersion obtained in some mixed compounds containing the carbon black may be affected by pellet hardness. Acceptable pellet hardness must be agreed to by the user and the producer.1.1 This test method covers a procedure for measuring individual pellet hardness of carbon black by the automated pellet hardness tester.1.2 The values stated in SI units are to be regarded as the standard. The values in parentheses are for information only.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Carbon Black8212;Automated Individual Pellet Hardness

ASTM D4122-05ae1 炭黑的标准规程.工业标准炭黑的评定

1.1 This practice covers guidelines for the production and testing for uniformity of a lot of carbon black to be used as an Industry Reference Black (IRB).1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Carbon Black-Evaluation of an Industry Reference Black

ASTM D4122-05e1 炭黑的标准规程.工业标准炭黑的评定

1.1 This practice offers guidelines for the production and testing for uniformity of a lot of carbon black to be used as an Industry Reference Black (IRB).1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Carbon Black8212;Evaluation of an Industry Reference Black

ASTM D4122-05 炭黑的标准规程.工业标准炭黑的评定

1.1 This practice offers guidelines for the production and testing for uniformity of a lot of carbon black to be used as an Industry Reference Black (IRB).1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Carbon Black8212;Evaluation of an Industry Reference Black

ASTM D4122-05a 炭黑的标准规程.工业标准炭黑的评定

1.1 This practice offers guidelines for the production and testing for uniformity of a lot of carbon black to be used as an Industry Reference Black (IRB).1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Carbon Black8212;Evaluation of an Industry Reference Black