G49 炭黑 标准查询与下载

ASTM D1510-02a 炭黑碘吸收值的标准试验方法

1.1 This test method covers the determination of the iodine adsorption number of carbon black.1.1.1 Procedure A is the original procedure for this determination.1.1.2 Procedure B specifies an increased sample mass of carbon black and volume of iodine solution (the ratio is the same as in Procedure A) which results in a simplified formula for the calculation of the iodine number.1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.3 The iodine adsorption number of carbon black has been shown to decrease with sample aging. Standard values for current SRB's may be obtained from the Subcommittee Chairman of D24.61.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Carbon Black8212;Iodine Adsorption Number

ASTM D1510-02 炭黑碘吸收值的标准试验方法

1.1 This test method covers the determination of the iodine adsorption number of carbon black.1.1.1 Procedure A is the original procedure for this determination.1.1.2 Procedure B specifies an increased sample mass of carbon black and volume of iodine solution (the ratio is the same as in Procedure A) which results in a simplified formula for the calculation of the iodine number.1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.3 The iodine adsorption number of carbon black has been shown to decrease with sample aging. Standard values for current SRB's may be obtained from the Subcommittee Chairman of D24.61.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Carbon Black8212;Iodine Adsorption Number

ASTM D6556-02a 用氮吸收法测定炭黑的总表面积和外表面积的标准试验方法

1.1 This test method covers the determination of the total surface area by the Brunauer, Emmett, and Teller (B.E.T. NSA) theory of multilayer gas adsorption behavior using multipoint determinations and the external surface area based on the statistical thickness surface area method.1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. (The minimum safety equipment should include protective gloves, sturdy eye and face protection).

Standard Test Method for Carbon Black8212;Total and External Surface Area by Nitrogen Adsorption

ASTM D6556-02 用氮吸收法测定炭黑的总表面积和外表面积的标准试验方法

1.1 This test method covers the determination of the total surface area by the Brunauer, Emmett, and Teller (B.E.T. NSA) theory of multilayer gas adsorption behavior using multipoint determinations and the external surface area based on the statistical thickness surface area method.1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. (The minimum safety equipment should include protective gloves, sturdy eye and face protection).

Standard Test Method for Carbon Black8212;Total and External Surface Area by Nitrogen Adsorption

ASTM D3265-02 炭黑的标准试验方法.着色强度

1.1 This test method covers the determination of the tint strength of carbon black relative to an industry tint reference black (ITRB).1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Carbon Black8212;Tint Strength

ASTM D1508-02(2007)e1 碳黑、球状细粒磨损的标准试验方法

Method A, Fines8212;The fines content of carbon black is related to the bulk flowability, dustiness, and, in some instances, the level of dispersion. Due to the many other variables that influence dispersion and handling, the significance of fines content must be determined by the user. Method B, Attrition8212;By comparing the percent fines and attrition, an indication can be obtained of pellet stability and the amount of fines that may be created by pellet degradation in conveying, handling or transit.1.1 This test method covers the determination of the fines and attrition of pelleted carbon black. 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Carbon Black, Pelleted Fines and Attrition

ASTM D1508-02e1 碳黑、球状细粒磨损的标准试验方法

1.1 This test method covers the determination of the fines and attrition of pelleted carbon black.1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Carbon Black, Pelleted Fines and Attrition

ASTM D1508-02e2 碳黑、球状细粒磨损的标准试验方法

1.1 This test method covers the determination of the fines and attrition of pelleted carbon black.1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Carbon Black, Pelleted Fines and Attrition

JIS K 6217-3:2001 橡胶工业用碳黑.基本特性.第3部分:特定表面面积的测定.CTAB 吸收法

この規格は，ゴム工業で原材料の配合剤として使用されるゴム用カーボンブラック(以下 ，カーボンブラックという。)の基本特性のうち，臭化n-へキサデンル トリメチルアンモニウム(cetyltrimethylammoniunn bromideともいい，以下CTABという。)の吸着による比表面積の求め方について規定する。この比表面積は，CTABの分子が入り込めない小さな細孔の面積を除外したものである。

Carbon black for rubber industry -- Fundamental characteristics -- Part 3: Determination of specific surface area -- CTAB adsorption methods

JIS K 6216-2:2001 橡胶工业用碳黑.一般要素.第2部分:标准参照黑色

この規格は，ゴム用カーボンブラックの測定方法に関連付けた検定用標準カーボンブラック (以下，SRBという。)の特性と公称値を規定する。

Carbon black for rubber industry -- General matters -- Part 2: Standard reference blacks

JIS K 6216-1:2001 橡胶工业用碳黑.一般要素.第1部分:炭黑成批货物取样程序

この規格は，ゴム用カーボンブラック(以下，カーボンブラックという。)のバルク輸送品，セミバルク輸送品及び袋詰包装品の試料採取方法について規定する。

Carbon black for rubber industry -- General matters -- Part 1: Carbon black shipment sampling procedures

JIS K 6217-5:2001 橡胶工业用碳黑.基本特性.第5部分:染色强度的测定

この規格は，ゴム工業で原材料の配合剤として使用されるゴム用カーボンブラック(以下，カーボンブラックという。)の基本特性のうち，比着色力検定用標準カーボンブラック(以下，ITRBという。)に対するカーボンブラックの比着色力の求め方について規定する。 この方法は，3種類の市販側定機器をべースにしたものであり，他の測定機器，例えばメコカラーマスタ一(MeecoColormaster)も使用できるが，少なくとも同等の性能をもっていなければならない。

Carbon black for rubber industry -- Fundamental characteristics -- Part 5: Determination of tinting strength

JIS K 6217-1:2001 橡胶工业用碳黑.基本特性.第1部分：碘吸收数的测定.滴定法

この規格は，ゴム工業で原材料の配合剤として使用されるゴム用カーボンブラック (以下，カーボンブラックという。)の基本特性のうち。滴定法によるよう素吸着量の求め方について規定する。 よう素吸着量はカーボンブラックの表面積に関連し，一般に窒素吸着比表面積に合致している。しかしながら，揮発分又は溶媒で抽出可能な物質などを多く合む場合には，この値はかなり低下する。したがって，よう素吸着量は必ずしもカーボンブラックの比表面積を規定するものではない。

Carbon black for rubber industry -- Fundamental characteristics -- Part 1: Determination of iodine adsorption number -- Titrimetric method

JIS K 6217-2:2001 橡胶工业用碳黑.基本特性.第2部分:特定表面面积的测定.氮吸收法.单点法

この規格は，ゴム工業で原材料の配合剤として使用されるゴム用カーボンブラック(以下，カーボンブラックという。)の基本特性のうち，窒素吸着法による比表面積(以下，窒素吸着比表面積という。)の求め方のうち，単点法について規定する。

Carbon black for rubber industry -- Fundamental characteristics -- Part 2: Determination of specific surface area -- Nitrogen adsorption methods -- Single-point procedures

JIS K 6217-4:2001 橡胶工业用碳黑.基本特性.第4部分:.邻苯二甲酸二丁酯吸收性的测定

この規格は，ゴム工業で原材料の配合剤として使用されるゴム用カーボンブラック(以下，カーボンブラックという。)の基本特性のうち，アブソープトメータを用いたDBP(フタル酸ジブチル)吸収量の求め方について規定する。DBP吸収量は，カーボンブラックが液体(DBP)を吸収する能力の尺度である。この特性はカーボンブラックのストラクチャーの指標である。

Carbon black for rubber industry -- Fundamental characteristics -- Part 4: Determination of dibutylphthalate absorption number

BS 5293-7:2001 橡胶工业用碳黑取样和试验.灰分含量测定方法

This International Standard specifies a method for determining the ash of all types of carbon black for use in the rubber industry.

Sampling and testing carbon black for use in the rubber industry - Method for determination of ash content

BS ISO 1125:1999+A1:2011 橡胶合成配料.碳黑.灰的测定

Rubber compounding ingredients. Carbon black. Determination of ash

BS 5293-10:2001 橡胶工业用碳黑取样和试验.碘吸收系数测定方法

This International Standard specifies a titrimetric method for the determination of the iodine adsorption number of carbon blacks for use in the rubber industry. The iodine adsorption number is related to the surface area of a carbon black, and is generally in agreement with the nitrogen surface area. However, it is significantly depressed in the presence of a high content of volatile or solvent-extractable materials; the iodine adsorption number therefore does not always provide a measure of the specific surface area of a carbon black.

Sampling and testing carbon black for use in the rubber industry - Method for determination of iodine absorption number

ASTM D4821-01a 炭黑的标准指南.试验方法精度和偏差的确认

1.1 This guide covers a procedure for using ASTM Standard Reference Blacks (SRBs) to continuously monitor the precision of those carbon black test methods for which standard values have been established. It also offers guidelines for trouble-shooting various test methods.1.2 This guide establishes the limits within which the statistical calibration procedure of Practice D3324 shall be applied and establishes the limits for an out-of-calibration condition beyond which the statistical calibration procedure of Practice D3324 shall not be applied.1.3 This guide uses statistical control chart methodology as discussed in STP-15-D to determine if a laboratory's test results differ significantly from the accepted values of the SRBs and provides a format for reporting test data for specified tests on the SRB blacks. 1.4 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Guide for Carbon Black8212;Validation of Test Method Precision and Bias

ASTM D1765-01 橡胶制品用碳黑的标准分类系统

1.1 This classification system is used to classify rubber grade carbon blacks by the use of a four-character nomenclature system. The first character gives some indication of the influence of the carbon black on the rate of cure of a typical rubber compound containing the black. The second character gives information on the average surface area of the carbon black. The last two characters are assigned arbitrarily. 1.2 All rubber-grade carbon blacks for which a number is currently assigned at the time of publication of this classification system are listed in Table 1 together with some of their typical properties. 1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Classification System for Carbon Blacks Used in Rubber Products