G49 炭黑 标准查询与下载

ASTM D1510-01 炭黑的标准试验方法.碘吸收值

1.1 This test method covers the determination of the iodine adsorption number of carbon black. 1.1.1 Procedure A is the original procedure for this determination. 1.1.2 Procedure B specifies an increased sample mass of carbon black and volume of iodine solution (the ratio is the same as in Procedure A) which results in a simplified formula for the calculation of the iodine number. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Carbon Black8212;Iodine Adsorption Number

ASTM D3324-01 炭黑的标准实施规程.用ASTM标准炭黑改进检验再生性

1.1 This practice provides a statistical procedure for improving test reproducibility when a laboratory cannot physically calibrate its apparatus to obtain the standard values of the ASTM reference blacks, within the ranges given in the precision statement of the test method concerned. 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Carbon Black8212;Improving Test Reproducibility Using ASTM Standard Reference Blacks

ASTM D6646-01 测定粒状和丸状活性炭的加速硫化氢突破容量的标准试验方法

1.1 This test method is intended to evaluate the performance of virgin, newly impregnated or in-service, granular or pelletized activated carbon for the removal of hydrogen sulfide from an air stream. A humidified air stream containing 1 % (by volume) hydrogen sulfide is passed through a carbon bed until 50 ppm breakthrough of H2S is observed. The H2S adsorption capacity of the carbon per unit volume at 99.5 % removal efficiency (g H2S/cm3 carbon) is then calculated. This test is not necessarily applicable to non-carbon adsorptive materials.1.2 This standard as written is applicable only to granular and pelletized activated carbons with mean particle diameters (MPD) less than 2.5 mm. See paragraph 5.3 if activated carbons with larger MPDs are to be tested.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Determination of the Accelerated Hydrogen Sulfide Breakthrough Capacity of Granular and Pelletized Activated Carbon

ASTM D1514-01 碳黑标准试验方法.筛渣

1.1 This test method describes the determination of the water wash sieve residue in regular untreated carbon blacks. It may not be applicable to oil-treated carbon blacks because the oil would prevent proper wetting of the black by water. 1.2 The values stated in SI units are to be regarded as the standard. The values in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific precautionary statements, see Section 6.

Standard Test Method for Carbon Black8212;Sieve Residue

ASTM D1510-01a 炭黑的标准试验方法.碘吸收值

1.1 This test method covers the determination of the iodine adsorption number of carbon black. 1.1.1 Procedure A is the original procedure for this determination. 1.1.2 Procedure B specifies an increased sample mass of carbon black and volume of iodine solution (the ratio is the same as in Procedure A) which results in a simplified formula for the calculation of the iodine number. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Carbon Black8212;Iodine Adsorption Number

ASTM D6556-01a 炭黑的标准试验方法.氮吸收法测定总的和外部表面积

1.1 This test method covers the determination of the total surface area by the Brunauer, Emmett, and Teller (B.E.T. NSA) theory of multilayer gas adsorption behavior using multipoint determinations and the external surface area based on the statistical thickness surface area method.1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. (The minimum safety equipment should include protective gloves, sturdy eye and face protection).

Standard Test Method for Carbon Black8212;Total and External Surface Area by Nitrogen Adsorption

ASTM D1765-01e1 橡胶制品用碳黑的标准分类系统

1.1 This classification system is used to classify rubber grade carbon blacks by the use of a four-character nomenclature system. The first character gives some indication of the influence of the carbon black on the rate of cure of a typical rubber compound containing the black. The second character gives information on the average surface area of the carbon black. The last two characters are assigned arbitrarily. 1.2 All rubber-grade carbon blacks for which a number is currently assigned at the time of publication of this classification system are listed in Table 1 together with some of their typical properties. 1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Classification System for Carbon Blacks Used in Rubber Products

ASTM D6556-01 炭黑的标准试验方法.氮吸收法测定总的和外部表面积

1.1 This test method covers the determination of the total surface area by the Brunauer, Emmett, and Teller (B.E.T. NSA) theory of multilayer gas adsorption behavior using multipoint determinations and the external surface area based on the statistical thickness surface area method.1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. (The minimum safety equipment should include protective gloves, sturdy eye and face protection).

Standard Test Method for Carbon Black8212;Total and External Surface Area by Nitrogen Adsorption

ISO 12985-1:2000 铝生产用碳素材料 焙烧阳极和阴极碳块 第1部分:用尺寸法测定表观密度

This part of ISO 12985 specifies a dimensions method for the determination of the apparent density of carbonaceous products used in the production of aluminium. This method is applicable to samples with a simple or well-defined geometry (cylindrical, rectangular parallelepipedical, cubic, etc.) and having a smooth surface profile. The accuracy of measurement is strongly influenced by the equipment used for sampling, i.e. the drilling and sawing machines.

Carbonaceous materials used in the production of aluminium - Baked anodes and cathode blocks - Part 1: Determination of apparent density using a dimensions method

ISO 12985-2:2000 铝生产用碳素材料 焙烧阳极和阴极碳块 第2部分:用静流法测定表观密度和开口孔隙率

This part of ISO 12985 specifies a hydrostatic method for the determination of the apparent density and the open (to water) porosity of carbonaceous products used in the production of aluminium. This hydrostatic method was developed principally to determine the open porosity but can also be used to measure the apparent density. This part of ISO 12985 is especially applicable to samples of complex on irregular geometry (due to drilling difficulties).

Carbonaceous materials used in the production of aluminium - Baked anodes and cathode blocks - Part 2: Determination of apparent density and of open porosity using a hydrostatic method

ISO 12989-1:2000 铝生产用碳素材料 焙烧阳极和部碳块 空气反应性的测定 第1部分:失重法

This part of ISO 12989 specifies a loss-in-mass method for the determination of the reactivity of carbonaceous products to air. The method was developed especially for anodes used in the production of aluminium.

Carbonaceous materials used in the production of aluminium - Baked anodes and sidewall blocks - Determination of the reactivity to air - Part 1: Loss in mass method

ISO 12986-1:2000 铝生产用碳素材料 预焙阳极和阴极碳块 第1部分:用三点法测定抗弯强度/剪切强度

This part of ISO 12986 describes a method for the determination of the bending/shear strength (flexural strength) of prebaked anodes and cathode blocks at temperatures in the range 20 ℃ to 30 ℃. The method is particularly appli-cable to prebaked anodes, but can be applied to cathode blocks. NOTE For the practical application of this International Standard the terms 'bending/shear strength' and 'flexural strength' may be considered equivalent.

Carbonaceous materials used in the production of aluminium - Prebaked anodes and cathode blocks - Part 1: Determination of bending/shear strength by a three-point method

ISO 12988-1:2000 铝生产用碳素材料 焙烧阳极 二氧化碳反应性的测定 第1部分:失重法

This part of ISO 12988 specifies a loss in mass method for the determination of the reactivity of carbonaceous products to carbon dioxide. This method was developed especially for baked anodes used in the production of aluminium.

Carbonaceous materials used in the production of aluminium - Baked anodes - Determination of the reactivity to carbon dioxide - Part 1: Loss in mass method

ASTM D1511-00 碳黑的标准试验方法.丸状材料尺寸分布

1.1 This test method covers the determination of the pellet size distribution of carbon black. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Carbon Black-Pellet Size Distribution

ASTM D1511-00e1 碳黑的标准试验方法.丸状材料尺寸分布

1.1 This test method covers the determination of the pellet size distribution of carbon black.1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Carbon Black-Pellet Size Distribution

ASTM D5805-00(2004)e1 (原批)橡胶的碳黑合成的标准试验方法

The carbon black content of an unvulcanized black or oil-black SBR masterbatch may be determined by this test method if an inert (CO2) atmosphere and a determinate (see Note 2) of known carbon black content are available. Note 28212;Determinate black masterbatch may be prepared by careful addition of exact amounts of rubber and carbon black on a mill. An alternative would be a thorough blending of a quantity of black masterbatch and determination of the carbon black by use of a previously established determinate.1.1 These test methods for the determination of the amount of carbon black in a masterbatch cover emulsion SBR-carbon black mixtures, but may be applicable to other polymers. Three test methods are included: SectionsInert Atmosphere Pyrolysis3-10Vacuum Pyrolysis11-17Thermogravimetric Analyzer18-24Note 1--The nomenclature used in these test methods is in accordance with Practice D1418.1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Rubber from Synthetic Sources--Carbon Black in Masterbatches

ASTM D5805-00(2009) (原批)橡胶的碳黑合成的标准试验方法

The carbon black content of an unvulcanized black or oil-black SBR masterbatch may be determined by this test method if an inert (CO2) atmosphere and a determinate (see Note 2) of known carbon black content are available. Note 28212;Determinate black masterbatch may be prepared by careful addition of exact amounts of rubber and carbon black on a mill. An alternative would be a thorough blending of a quantity of black masterbatch and determination of the carbon black by use of a previously established determinate.1.1 These test methods cover the determination of the amount of carbon black in a masterbatch and cover emulsion SBR-carbon black mixtures, but may be applicable to other polymers. Three test methods are included: Sections Inert Atmosphere Pyrolysis 3-10 Vacuum Pyrolysis11-17 Thermogravimetric Analyzer18-24 Note 18212;The nomenclature used in these test methods is in accordance with Practice D 1418. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Rubber from Synthetic Sources--Carbon Black in Masterbatches

ASTM D5230-00e2 炭黑的标准试验方法.自动形成单个颗粒的破碎强度

1.1 This test method covers a procedure for measuring the crush strength of individual pellets of carbon black by the automated pellet hardness tester.178;1.2 The values stated in SI units are to be regarded as the standard. The values in parentheses are for information only.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Carbon Black8212;Automated Individual Pellet Hardness

ASTM D5230-00e1 炭黑的标准试验方法.自动形成单个颗粒的破碎强度

1.1 This test method covers a procedure for measuring the crush strength of individual pellets of carbon black by the automated pellet hardness tester.178;1.2 The values stated in SI units are to be regarded as the standard. The values in parentheses are for information only.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Carbon Black8212;Automated Individual Pellet Hardness

ASTM D5230-00 炭黑的标准试验方法.自动形成单个颗粒的破碎强度

1.1 This test method covers a procedure for measuring the crush strength of individual pellets of carbon black by the automated pellet hardness tester. 1.2 The values stated in SI units are to be regarded as the standard. The values in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Carbon Black-Automated Individual Pellet Hardness