G49 炭黑 标准查询与下载

HG/T 2797.5-1996 硅铝炭黑杂质的测定

本标准规定了各种硅铝炭黑所含的通不过850μm筛的物质的一种试验方法。 本标准适用于各种类型硅铝炭黑杂质的测定。

Determination of silicon aluminum carbon black impurities

HG/T 2797.6-1996 硅铝炭黑倾注密度的测定

本标准规定了硅铝炭黑倾注密度的测定方法。 本准适用于各种类型硅铝炭黑倾注密度的测定。

Determination of pour density of silicon aluminum carbon black

HG/T 2797.7-1996 硅铝炭黑加热减量的测定

本标准规定了硅铝炭黑加热减量的测定方法。 本标准适用于各种类型硅铝炭黑加热减量的测定。

Determination of heating loss of silicon aluminum carbon black

HG/T 2797.3-1996 硅铝炭黑邻苯二甲酸二丁酯吸收值的测定

本标准规定了硅铝炭黑邻苯二甲酸二丁酯吸收值的测定方法。 本标准适用于各种类型硅铝炭黑邻苯二甲酸二丁酯吸收值的测定。

Determination of absorption value of dibutyl phthalate of silicon aluminum carbon black

HG/T 2797.2-1996 硅铝炭黑吸碘值的测定

本标准规定了硅铝炭黑吸碘值的测定方法。 本标准适用于各种类型硅铝炭黑吸碘值的测定。

Determination of iodine absorption value of silicon aluminum carbon black

HG/T 2796-1996 硅铝炭黑包装、贮运、采样及验收方法

本标准规定了袋装硅铝炭黑包装、贮存、运输、采样及验收方法。

Packaging, storage and transportation, sampling and acceptance of silicon aluminum carbon black

DIN ISO 1124:1996 橡胶混合配料.炭黑交货取样程序

The document specifies procedures for the sampling of carbon black for use in the rubber industry, delivered in bulk, semi-bulk or packages.

Rubber compounding ingredients - Carbon black shipment sampling procedures; identical with ISO 1124:1988

ASTM D5817-96 碳黑,颗粒缩径和大型样品混合用标准规程

1.1 This practice describes the procedure for the reduction of gross samples of pelleted carbon black to the appropriate size for testing and the procedure for blending of pelleted carbon black. These techniques are intended to minimize variations in measured characteristics between test samples. Standard terminology relating to carbon black samples is found in Terminology D3053. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Carbon Black, Pelleted-Reduction and Blending of Gross Samples

ASTM D5919-96(2011) 在ppb浓缩时吸附用微缩等温线技术对活性炭吸附能力测定用标准操作规程

This practice allows the adsorption capacity at equilibrium of an activated carbon for adsorbable constituents present in water to be determined. The Freundlich K and 1/n constants that can be calculated based upon information collected using this practice can be used to estimate carbon loading capacities and usages rates for the constituent present in a water stream at other concentrations. 1.1 This practice covers the assessment of activated carbon for the removal of low concentrations of adsorbable constituents from water and wastewater using the bottle point isotherm technique. It can be used to characterize the adsorptive properties of virgin and reactivated activated carbons. 1.2 This practice can be used in systems with constituent concentrations in the low milligrams per litre or micrograms per litre concentration ranges. 1.3 This practice can be used to determine the adsorptive capacity of and Freundlich constants for volatile organic compounds provided the handling procedures described in this practice are followed carefully. 1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5 The following safety caveat applies to the procedure section of this practice: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Determination of Adsorptive Capacity of Activated Carbon by a Micro-Isotherm Technique for Adsorbates at ppb Concentrations

ASTM D4122-96ae1 炭黑的标准操作规程.工业标准炭黑的评定

1.1 This practice offers guidelines for the production and testing for uniformity of a lot of carbon black to be used as an Industry Reference Black (IRB). 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Carbon Black-Evaluation of an Industry Reference Black

ISO 11234:1995 橡胶配合剂 炭黑(造粒) 灰份测定

Specifies a method for the determination of the dust content of pelletized carbon blacks. Permits a differentiation to be made between micro-pellets and dust and is applicable to all pelletized carbon blacks for the rubber industry.

Rubber compounding ingredients - Carbon black (pelletized) - Determination of dust content

ISO 1306:1995 橡胶配合剂 炭黑(造粒) 倾注密度的测定

Gives a method for the determination of the pour density of all types of pelletized carbonblacks for use in the rubber industry. Replaces the third edition which has been technically revised.

Rubber compounding ingredients - Carbon black (pelletized) - Determination of pour density

ISO 6810:1995 橡胶配合剂 炭黑 表面积的测定 CTAB吸附法

Describes adsorptive methods for the determination of the surface area of carbon blacks by means of hexadecyltrimethylammonium bromide (CTAB). Excluded is the area of micropores that are too small to admit molecules of CTAB. Cancels and replaces the first edition, which has been technically revised.

Rubber compounding ingredients - Carbon black - Determination of surface area - CTAB adsorption methods

HG/T 2725-1995 散装炭黑采样方法

本标准规定了三格底卸式铁路槽车中散装炭黑的采样方法和数据报告方法。 本标准也适用于分格的公路拖车中散装炭黑的采样。

Bulk carbon black sampling method

BS 5293-21:1995 橡胶工业用碳黑试验和取样.第21部分:橡胶制品用碳黑分类制度

Classifies carbon blacks by use of a four-character nomenclature system indicating in particular effect on rate cure and particle size.

Sampling and testing carbon black for use in the rubber industry - Classification system for carbon blacks used in rubber products

BS 5293-13:1995 橡胶工业用炭黑取样和试验.第13部分:着色力测定方法

This International Standard specifies a method for the determination of the tinting strength of carbon black relative to an industry tint reference black. The method is based on the use of three different commercial instruments. Other instruments may be used but they shall have at least equivalent perform-ance. NOTE 1 Details of the manufacturers of the Erichsen Tint Tester are given in the relevant clause of this International Standard. The Densichron reflectometer and the Meeco Colormaster are no longer available commercially, but the methods are included for the benefit of users of these in-struments.

Sampling and testing carbon black for use in the rubber industry - Method for determination of tinting strength

ASTM D4583-95(2009) 碳黑&8212的标准惯例.从工艺控制数据的分析中计算工艺指数

This practice will provide the following: (1) a statistical summary of individual production run data plotted on a control chart; (2) a statistical summary of data from multiple production runs; (3) a procedure to relate the average and variation of these data groups to specification limits, and (4) indexes for comparing different manufacturing units for projecting future capabilities or as historical reference.1.1 This practice covers (1) a statistical procedure for analyzing the test data generated in the statistical process control of a carbon black manufacturing process; (2) a format for reporting process capability determined from the analysis of control chart data of an individual production run, and (3) a format for reporting process performance determined from the analysis of control chart data of an individual production run. 1.2 This practice specifically applies to the analysis of pelleted carbon black samples taken during the manufacturing process prior to storage. This practice does not apply to shipment samples taken from hopper cars or other containers or packages. 1.3 This practice is specifically designed to be used for those test methods given in Classification D 1765 which specify target values. However, these techniques are applicable to other test methods on carbon black. 1.4 This practice describes the calculation for two methods of determining capability factors from an analysis of process control data. 1.4.1 Process capability (Cp) is a measurement of variation calculated from the process control chart data with the use of an estimated standard deviation (ˆσ) from the mean value of the moving range (R) chart. The calculation of the process capability (Cp and Cpk) indexes can be used as historical information or to predict future performance of the process, but are only valid when the process is in a state of statistical control. 1.4.2 Process performance (Pp) is a measurement of variation calculated from the process control chart data using sample standard deviation(s). The calculation of the process performance (Pp and Ppk) indexes are used for a historical reference of a process' performance and does not require a state of statistical control.

Standard Practice for Carbon Black8212;Calculation of Process Indexes From an Analysis of Process Control Data

ASTM D1509-95(2012) 炭黑加热损耗的标准试验方法

1.1 These test methods cover the determination of the heating loss of carbon black at 125??C. This heating loss consists primarily of moisture, but other volatile materials may also be lost. These test methods are not applicable to treated carbon blacks that contain added volatile materials, if moisture loss is to be measured. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Methods for Carbon Blackmdash;Heating Loss

ASTM D4583-95(2004) 炭黑的标准实施规程.从工艺控制数据的分析中计算工艺指数

This practice will provide the following: (1) a statistical summary of individual production run data plotted on a control chart; (2) a statistical summary of data from multiple production runs; (3) a procedure to relate the average and variation of these data groups to specification limits, and (4) indexes for comparing different manufacturing units for projecting future capabilities or as historical reference.1.1 This practice covers (1) a statistical procedure for analyzing the test data generated in the statistical process control of a carbon black manufacturing process; (2) a format for reporting process capability determined from the analysis of control chart data of an individual production run, and (3) a format for reporting process performance determined from the analysis of control chart data of an individual production run.1.2 This practice specifically applies to the analysis of pelleted carbon black samples taken during the manufacturing process prior to storage. This practice does not apply to shipment samples taken from hopper cars or other containers or packages.1.3 This practice is specifically designed to be used for those test methods given in Classification D 1765 which specify target values. However, these techniques are applicable to other test methods on carbon black.1.4 This practice describes the calculation for two methods of determining capability factors from an analysis of process control data.1.4.1 Process capability (Cp) is a measurement of variation calculated from the process control chart data with the use of an estimated standard deviation (963;) from the mean value of the moving range (R) chart. The calculation of the process capability (Cp and Cpk) indexes can be used as historical information or to predict future performance of the process, but are only valid when the process is in a state of statistical control.1.4.2 Process performance (Pp) is a measurement of variation calculated from the process control chart data using sample standard deviation(s). The calculation of the process performance (Pp and Ppk) indexes are used for a historical reference of a process' performance and does not require a state of statistical control.

Standard Practice for Carbon Black8212;Calculation of Process Indexes From an Analysis of Process Control Data

ASTM D1509-95(2007) 碳黑加热损耗的标准测试方法

In addition to determining the heating loss (primarily moisture content) of carbon black, these drying conditions are used to prepare samples prior to performing other carbon black tests. When larger samples are prepared for other tests, use an open vessel of suitable dimensions so that the depth of the black is no more than 10 mm during conditioning. Carbon black is hygroscopic. The amount of moisture absorbed is related to the surface area of the black and to the relative humidity, ambient temperature, and time to which the material is exposed.1.1 These test methods cover the determination of the heating loss of carbon black at 125176;C. This heating loss consists primarily of moisture, but other volatile materials may also be lost. These test methods are not applicable to treated carbon blacks that contain added volatile materials, if moisture loss is to be measured.1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Methods for Carbon Black-Heating Loss