化学试剂综合标准-分析测试百科网

KS M 2111-2004 航空润滑油氧化稳定性试验方法

이 규격은 항공 피스톤 발동기 윤활유의 산화 안정도를 시험하는 방법에 대하여 규정한다.

Testing method for oxidation characteristics of lubrication oil for aircraft reciprocating engines

ICS: 75.1
CCS: G60
发布: 2004-06-30
实施: 2004-06-30

KS M 2014-2004 原油及石油产动粘度试验方法及石油产品黏度指数计算方法

이 규격은 뉴턴 액체상의 투명ㆍ불투명한 원유 및 석유 제품의 동점도를 유리제 모세관식

Testing methods for kinematic viscosity and calculating method for viscosity index of crude oil and petroleum products

ICS: 75.04
CCS: G60
发布: 2004-06-30
实施: 2004-06-30

ASTM E1910/E1910M-04(2009) 农业PH值控制剂测试方法

This test method is intended for products sold as tank mix adjuvants for use with agricultural products. Part A provides a determination of whether the pH modification characteristics of the adjuvant tested meet the definition of an acidifier, alkalinity agent, or a basic blend in Terminology E1519. Part B provides a measure of the buffer capacity of the adjuvant. This can be used to estimate the amount of a buffer that will be required to keep a spray solution at the desired pH. Other pH standards can be used (see Test Method E70) as long as the pHs measured are not outside the range of the standards used. If samples of the material to be used in a particular application are available, the first method can be used to determine what adjuvant rate is required to obtain the desired pH. The ability of an adjuvant to adjust the pH of a particular system will depend on the initial pH before addition. The second method can be used to determine the amount of an adjuvant required to change the pH of a quantity of spray solution to the required value (see Note 1). Note 18212;Many acidifiers and basic blends also are buffers, so the pH change does not provide a useful measure of buffer capacity.1.1 These test methods cover determining if an adjuvant meets the definitions of an acidifier, a basic blend, alkalinity agent, or buffer in Terminology E1519. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Test Method for Agricultural pH Control Agents

ICS: 65.020.99
CCS: G60
发布: 2004
实施

KS M 1802-2003 活性炭试验方法

이 규격은 활성탄의 시험 방법에 대하여 규정한다.

Test methods for activated carbon

ICS: 71.100.00
CCS: G60
发布: 2003-12-03
实施: 2003-12-03

ASTM D3911-03 设计基本事故(DBA)的模拟条件下评价轻水核电站用涂层的标准试验方法

This test method is designed to provide a uniform test to determine the suitability of Coating Service Level 1 coatings used inside primary containment of light-water nuclear facilities under simulated DBA conditions. This test method is intended only to demonstrate that under DBA conditions, the coatings will remain intact and not form debris which could unacceptably compromise the operability of engineered safety systems. Deviations in actual surface preparation and in application and curing of the coating materials from qualification test parameters require an engineering evaluation to determine if additional testing is required. Since different plants have different tolerance levels for coating conditions, the definition of appropriate acceptance criteria is to be developed by the license holder based on individual plant engineered safety systems operability considerations.1.1 This test method establishes procedures for evaluating protective coating systems test specimens under simulated DBA conditions. Included are a description of conditions and apparatus for temperature-pressure testing, and requirements for preparing, irradiating, testing, examining, evaluating, and documenting the samples.1.2 The values stated in inch-pound and degrees F units are to be regarded as the standard. The SI values given in parentheses are for information only.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Evaluating Coatings Used in Light-Water Nuclear Power Plants at Simulated Design Basis Accident (DBA) Conditions