共找到 624 条与 化工设备 相关的标准,共 42 页
Specification for construction and acceptance of wet-type gas holders with metal welded structure
This specification establ ishes the design, performance, and acceptancëE?$i rements for the OK-293A/AWW Control Group, Guided Weapon, herein a f t e r referred to as the control group.
GUIDED WEAPON CONTROL GROUP OK-293A/AWW
This specification establ ishes the desig nper for m ance and acceptance requirements for the AN/APN-l94(v) Electronic Altimeter Set ,hereinreferred to as the equipment.
LAUNCHER CONTAINER,"A" SIZE SONOBUOY LAU-126/A
Tolerances for construction of tubular heat exchangersDie Rohrbündel-W?rmeaustauscher brauchen der bildlichen Darstellung nicht zu entsprechen, nur die angegebenen bzw. vereinbarten Abma?e und Toleranzen sind einzuhalten.Diese Norm legt keine Zahlenwert
Tolerances for construction of tubular heat exchangers
This specification covers the requirements for the development and fabrication of a field change kit to the AN/URT-23(C) Transmitter ( hereinafter referred to as the transmitter).
FIELD CHANGE KIT FOR VARIABLE OUTPUT POWER CAPABILITY
This specification covers one type of plastic flag case for use with the interment flag
CASE, FLAG, INTERMENT
This amendment forms a part of Military Specification MIL-C-43603B,dated 30 June 1980, and is approved for use by all Departments and Agencies of the Department of Defense.
CANTEEN, WATER, COLLAPSIBLE, 2-QUART CAPACITY
Battery tanks for aboveground storage of mineral-oils, connection lines
Floating head heat exchanger with flanged floating head; number of passes: 2,4 and 8, tubes 25, square tube pitch 32, number and pattern of tubes, tie rods and slide rails
Floating head heat exchanger with flanged floating head; number of passes: 2,4 and 8, tubes 25, square tube pitch 32; number and pattern of tubes, tie rods and slide rails
Floating head heat exchanger with welded floating head; number of passes: 2, tubes 25, square tube pitch 32, number and pattern of tubes, tie rods and slide rails
Floating head heat exchanger with welded floating head; number of passes: 2, tubes 25, square tube pitch 32; number and pattern of tubes, tie rods and slide rails
This specification covers one type and s i z e canteen cover fabricated from nylon cloth, nylon webbing and acrylicpileliner material.
COVER, WATER CANTEEN, LC-2
Steel storage tanks. Anticorrosive coating. Minimum technical requirements.
Steel storage tanks-anticorrosive coating. Defect detection by 2500 controller.
Regenerator bottoms from hydrogen fluoride (HF) alkylation are often 2-phase systems. The lower phase is relatively rich in HF, containing about 30-40%; and the upper phase is essentially hydrocarbon containing small concentrations (about 0-5%) of HF. The water content of the HF-rich lower phase is usually less than 10%, and that of the upper phase is usually less than 5%. This method is satisfactory for the determination of water in both types of samples. The unsaturates present in the oil do not interfere in the titration for water.
Water in Regenerator Bottoms from Hydrogen Fluoride Alkylation
This method is for determining hydrogen fluoride (HF) in HF alkylation regenerator bottoms. The bottoms material can be either a single or 2-phase system; the upper phase in a 2-phase system is rich in organic material and contains little HF, while the lower phase is rich in HF. The lower phase may contain large concentrations of water when there is appreciable water present in any of the feed streams. This method is applicable to both types of samples.
Hydrogen Fluoride in HF Alkylation Regenerator Bottoms
This specification describes the general s t y l e and format for the preparation of the Technical Documentation L,st. Th s technical manual is applicable to A i r c r a f t Weapon Systems, major Airborne Missiles, i n s t all e d Systems and associated equipment.
MANUAL, TECHNICAL, WEAPON SYSTEMS TECHNICAL DOCUMENTATION LIST, PREPARATION OF
This specification: cov&s a 2 quart capacity collapsible, plastic water canteen with or without a'cover.' .
CANTEEN, WATER, COLLAPSIBLE, 2-QUART CAPACITY
1.1 This specification covers the performance requirements for general-purpose water baths ordinarily used in testing operations. It is applicable to gravity-convection and forced-circulation water baths operating in the range from 5176;C above ambient to 100176;C and having a water volume up to 100 L.1.2 This specification covers unloaded, covered water baths.
Standard Specification for Gravity-Convection And Forced-Circulation Water Baths
1.1 This specification covers the performance requirements for general-purpose water baths ordinarily used in testing operations. It is applicable to gravity-convection and forced-circulation water baths operating in the range from 5176;C above ambient to 100176;C and having a water volume up to 100 L.1.2 This specification covers unloaded, covered water baths.
Standard Specification for Gravity-Convection and Forced-Circulation Water Baths
1.1 This specification covers the performance requirements for general-purpose water baths ordinarily used in testing operations. It is applicable to gravity-convection and forced-circulation water baths operating in the range from 5176;C above ambient to 100176;C and having a water volume up to 100 L.1.2 This specification covers unloaded, covered water baths.
Standard Specification for Gravity-Convection And Forced-Circulation Water Baths
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号