G94 非金属化工机械设备 标准查询与下载

HG/T 2057-2003 搪玻璃搅拌容器用机械密封

本标准规定了在搪玻璃搅拌容器上部安装的搪玻璃搅拌轴用机械密封型式—、主要尺寸、标记和技术要求。 本标准适用于公称压力小于或等于1 MPa，容器内工作介质温度小于等于200~C的搪玻璃搅拌容器用机械密封，搅拌轴(或轴套)外径为40mm～140mm，转轴线速度小于2m/s。

Stirred glass lined vessel mechanical seals

ASME RTP-1d Addenda-2004 增强热固性塑料耐腐蚀设备.附录

Reinforced thermoset plastic corrosion resistant equipment; Addenda

ASTM F2389-04 压力标定的聚丙烯管道系统的标准规范

1.1 This specification establishes requirements for polypropylene (PP) piping system components made to metric sizes and IPS schedule 80 sizes, and pressure rated for water service and distribution supply (see Appendix X1). Included are criteria for materials, workmanship, dimensions and tolerances, product tests, and marking for polypropylene (PP) piping system components such as pipe, fittings, valves, and manifolds.1.2 The components governed by this specification shall be permitted for use in water service lines, hot-and-cold water distribution, hydronic heating, and irrigation systems.1.3 The pipe and fittings produced under this specification shall be permitted to be used to transport industrial process fluids, effluents, slurries, municipal sewage, etc. The user shall consult the manufacturer to determine whether the material being transported is compatible with the polypropylene piping system and will not affect the service life beyond limits acceptable to the user.1.4 Units8212;The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.

Standard Specification for Pressure-rated Polypropylene (PP) Piping Systems

CSA B621-03-2003 用于运输 3、4、5、6.1、8 和 9 类危险货物的公路罐体、可移动罐体、分隔罐体和集装箱的选择和使用 更新编号： 1; 更新#2

Canadian Standards Association (CSA) standards are developed through a consensus standards development process approved by the Standards Council of Canada. This process brings together volunteers representing varied viewpoints and interests to achieve co

Selection and use of road tanks, removable tanks, compartmentalized tanks and containers for the transport of dangerous goods of classes 3, 4, 5, 6.1, 8 and 9 Update no. 1; Update #2

CSA B622-03-2003 用于运输 2 类危险货物的沟槽式罐体、多沟槽式罐体和可移动罐体的选择和使用更新 第1号； 更新#2

Canadian Standards Association (CSA) standards are developed through a consensus standards development process approved by the Standards Council of Canada. This process brings together volunteers representing varied viewpoints and interests to achieve

Selection and use of routed tanks, multiple routed tanks and removable tanks for the transport of Class 2 dangerous goods Update No. 1; Update #2

CSA B620-03-2003 危险品运输用公路储罐和便携式储罐.第3版

Highway Tanks and Portable Tanks for the Transportation of Dangerous Goods Third Edition

Highway Tanks and Portable Tanks for the Transportation of Dangerous Goods Third Edition

ASME RTP-1c Addenda-2003 增强热固性塑料耐腐蚀设备

Reinforced thermoset plastic corrosion resistant equipment; Addenda to ASME RTP-1-2000

KS L 7104-2002 化学试验室用搪瓷仪器

이 규격은 이화학용 법랑 기구(이하 기구라 한다.)에 대하여 규정한다.

Enamel apparatus for laboratory

HG 3209-2002 耐酸陶瓷设备通用技术条件

本标准规定了耐酸陶瓷设备的材质分类、技术要求、试验方法、检验规则、标志、包装和贮运。 本标准适用于化学工业及其他工业用耐酸陶瓷设备及零部件。

General technic specification for acid resistant ceramic equipment

HG/T 3210-2002 耐酸陶瓷材料性能试验方法

本标准规定了耐酸陶瓷材料抗压强度、抗弯强度、抗拉强度、抗冲击强度、吸水率、气孔率、体积密度、耐酸度、耐碱度及耐温度急变性等性能的试验方法。 本标准适用于化学工业及其他工业用耐酸陶瓷设备及零部件的材料性能试验。

Methods of test for the performance of acid resistant ceramic material

KS L 8011-2002 碳化硅发热元件

이 규격은 탄화규소 발열체(이하 발열체라고 한다.)에 대하여 규정한다.

Silicon carbide electric heating element

HG/T 3690-2001 工业用钢骨架聚乙烯塑料复合管

本标准规定了工业用钢骨架聚乙烯塑料复合管的基本性能、产品分类、要求、试验 方法、检验规则、标志、包装、运输和贮存。 本标准适用于以聚乙烯为基体，钢丝焊接而成的网状钢骨架为增强体，经连续挤出成型的复合管材，可用于石油、化工、医药、冶金、采矿以及船舶、市政建设、食品等行业。管材输送介质温度范围为O～70℃。

Steel framed polyethylene plastic pipes for industry

HG/T 3691-2001 工业用钢骨架聚乙烯塑料复合管件

本标准规定了工业用钢骨架聚乙烯塑料复合管件的基本性能、产品分类、要求、试 验方法、检验规则、标志、包装、运输和贮存。 本标准适用于以薄钢板均匀冲孔后卷筒焊接制成加强骨架后与聚乙烯注塑成型的钢骨架塑料复合管件，可用于石油、化工、医药、冶金、采矿以及船舶、市政建设、食品等行业。管件输送介质温度范围为O～70℃。

Fitting of steel framed polyethylene plastic pipes for industry

HG 2432-2001 搪玻璃设备技术条件

本标准规定了搪玻璃设备设计、制造、试验、检验、验收、包装运输等的基本要求。 本标准适用于设计压力小于或等于1.0MPa，设计温度高于-20℃，低于或等于200℃的搪玻璃设备、塔节、管道及管件。

Qaulity standard of glass-lined equipment for industry

HG/T 3693-2001 橡胶膜片式稳压阀技术条件

本标准规定了橡胶膜片式稳压阀的定义、要求、试验方法、检验规则及标志、包装、贮存。 本标准适用于公称压力PN≤O.6MPa，公称通径DN为2～6mm，环境温度不大于80℃，介质为氢气、氮气、空气等化工仪表专用稳压阀。

Specofocations for rubber diaphragm pressure regulator

ASME RTP-1 INTERPRETATIONS-2002 ASME RTP-1解释

As a service to persons a_-o use the RTP-1 Standard, the RTP Committee reni;rs interpretationsof the requirements upon request. The procedure for requesting an interpretation is described in thefollowing paragraphs.The interpretations include all replies that have been approved by the RTP Main Committee inresponse to inquiries concerning interpretation of the Standard.An interpretation applies either to the edition and addenda in effect on the date of issuance of theinterpretation or the edition and addenda stated in the interpretation. Subsequent revisions to the Standardmay supersede the interpretation.

ASME RTP-1 INTERPRETATIONS

ASME RTP-1b Addenda-2002 增强热固塑料耐腐蚀设备.补充

Reinforced thermoset plastic corrosion resistant equipment; Addenda

ASTM D5068-02 评定用漆刷的制备的标准规程

1.1 This practice describes the preparation of paint brushes for evaluation. 1.2 This practice is applicable to paint brushes 2 to 4 in. (50 to 100 mm) in width. 1.3 This standard does not purport to address the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Preparation of Paint Brushes for Evaluation

BS 7158:2001 排放物和污物用的塑料制检查容器

This British Standard specifies requirements for plastics inspection chambers for use at depths to invert not exceeding 6 m in the construction of drainage and sewerage systems. It is applicable to non-man-entry chambers with or without raising pieces and having a nominal cross-section as recommended in Table NB.2 of BS EN 752-3:1997, as amended in 2000. The chambers are classified into four grades as a function of stiffness (see 7.6) and strength (see 7.7), to suit different depths of installation and location for exposure to surface loading (see Annex H). Attention is drawn to BS EN 124:1994 and BS 4660 which specify requirements for covers and frames for drainage purposes that are applicable to inspection chambers. This standard specifies materials, dimensions and tolerances, physical and performance characteristics and marking for plastics inspection chambers for drains and sewers.

Plastics inspection chambers for drains and sewers - Specification

DIN 28052-6:2001 化工设备.加工厂使用非金属材料对混凝土构件的表面处理.第6部分:试验方法

The document specifies requirements and tests for surface treatment of concrete components in process plants using non-metallic materials.

Chemical apparatus - Surface treatment of concrete components in process plants using non-metallic materials - Part 6: Test methods