H12 轻金属及其合金分析方法 标准查询与下载

KS D ISO 3979:2002 铝和铝合金.镍含量的测定.丁二酮肟分光光度法

이 규격은 알루미늄과 알루미늄 합금의 니켈을 정량하기 위한 디메틸글리옥심을 이용한 분광

Aluminium and aluminium alloys－Determination of nickel－Spectrophotometric method using dimethylglyoxime

KS D ISO 3981:2002 铝和铝合金.镍含量的测定.原子吸收分光光度法

이 규격은 알루미늄 및 그의 합금 중의 니켈을 정량하기 위한 원자 흡수 분광 광도법에

Aluminum and aluminum alloys ? Determination of nickel－Atomic absorption spectrophotometric method

KS D ISO 794:2002 镁和镁合金.铜含量的测定.草酰二肼光度法

이 규격은 마그네슘과 마그네슘 합금 내의 구리 함량을 측정하기 위한(Oxalyldihy

Magnesium and magnesium alloys-Determination of copper content-Oxalyldihydrazide photometric method

KS D ISO 791:2002 镁合金.铝含量的测定.8一羟基喹啉重量法

이 규격은 지르코늄, 토륨 또는 희토류 원소를 제외한 마그네슘 중의 알루미늄을 정량하기

Magnesium alloys－Determination of aluminium－8－hydroxyquinoline gravimetric method

KS D ISO 1783:2002 镁合金.锌的测定.滴定法

이 규격은 카드뮴을 함유하지 않은 마그네슘 합금 중 아연을 정량하기 위한 부피 분석법에

Magnesium alloys-Determination of zinc-Volumetric method

KS D ISO 7692:2002 钛铁.钛含量的测定.滴定法

이 규격은 티타늄철에 포함되어 있는 티타늄 함량을 측정하기 위한 적정법에 대하여 규정한다.

Ferrotitanium－Determination of titanium content－Titrimetric method

KS D 8341-2-2002 铝和铝合金有色阳极氧化物涂层耐光性加速测试方法.第2部分:紫外线耐光性测验

이 규격은 알루미늄 및 알루미늄 합금 제품(이하 제품이라 한다.)에 처리한 착색 양극 산화

Accelerated test methods for light fastness of coloured anodic oxide coatings on aluminium and aluminium alloys－Part 2：Test for light fastness to ultra－violet lignt

KS D 8341-2002 铝和铝合金有色阳极氧化涂层的耐光性加速试验方法.第1部分:光的色牢度试验

이 규격은 알루미늄 및 알루미늄합금 제품(이하 제품이라고 한다.)에 입힌 착색 양극 산화

Accelerated test methods for light fastness of coloured anodic oxide coatings on aluminium and aluminium alloy－Part 1：Test for light fastness to artificial light

KS D 0230-2002 铝和铝合金的大气腐蚀试验

이 규격은 알루미늄 및 알루미늄합금 소재 및 표면 처리재의 자연 환경 아래에서의 화학적ㆍ물

Test methods for weathering test of aluminium and aluminium alloy

KS D 2034-2002 镁合金中钙含量测定方法

이 규격은 마그네슘 합금의 칼슘 분석 방법에 대하여 규정한다.

Method for determination of calcium in magnesium alloys

DIN EN 12441-3:2002 锌及锌合金.化学分析.第3部分:铅、镉、铜含量测定.火焰原子吸收光谱法

This European Standard specifies a flame atomic absorption spectrometric method for the determination of lead, copper and cadmium in zinc and zinc alloys.It is applicable to the products specified in EN 988, EN 1179, EN 1774, EN 12844 and prEN 13283. It is suitable for the determination of lead contents (mass fractions) between 0,0005 % and 2,5%, cadmium contents (mass fractions) between 0,0005 % and 0,3%, and copper contents (mass fractions) between 0,0005 % and 4 %.#,,#

Zinc and zinc alloys - Chemical analysis - Part 3: Determination of lead, cadmium and copper; FAAS procedure; German version EN 12441-3:2001

JIS H 1366:2002 铝和铝合金中铅含量测定方法

この規格は，アルミニウム及びアルミニウム合金中の鉛定量方法について規定する。

Methods for determination of lead in aluminium and aluminium alloys

JIS H 1364:2002 铝合金中铋含量的测定方法

この規格は，アルミニウム及びアルミニウム合金中のビスマス定量方法について規定する。

Methods for determination of bismuth in aluminium and aluminium alloys

KS D ISO 3980:2002 铝和铝合金.铜含量的测定.原子吸收分光光度法

이 규격은 알루미늄과 알루미늄합금 중의 구리를 원자 흡수 분광 광도계법에 의하여 정량하기

Aluminium and aluminium alloys：Determination of copper content－Atomic absorption spectrophotometric method

KS D ISO 793:2002 铝和铝合金.铁含量的测定.菲罗啉光度法

이 국제 규격은 알루미늄과 알루미늄합금의 철 함량 측정을 위한 분광법에 대해 규정한다.

Aluminium and aluminium alloys－Determination of iron－Orthophenanthroline photometric method

KS D ISO 808:2002 铝和铝合金.硅含量的测定.还原硅钼酸络含物分光光度法

이 규격은 알루미늄과 알루미늄합금 내부의 실리콘의 함량 측정을 위한 분광법을 규정하고 있다

Aluminium and aluminium alloys－Determination of silicon－Spectrophotometric method with the reduced silicomolybdic complex

ASTM E1938-02 用二安替比林甲烷分子吸收光谱测定法测定镍合金中钛含量的标准试验方法

This practice is used for the analysis of nickel and nickel base alloy samples by molecular absorption spectrometry to check compliance with compositional specifications. It is assumed that all who use the procedure will be trained analysts capable of performing common laboratory procedures skillfully and safely. It is expected that the work will be performed in a properly equipped laboratory and that proper waste disposal procedures will be followed. Appropriate quality control practices must be followed such as those described in Guide E 882.1.1 This test method covers the determination of titanium in nickel alloys in the 0.3 through 5.0 % range. With appropriate reference materials the test method may be extended down to 0.05 %.1.2 Molybdenum, if present, may cause a high bias to the extent of 0.001 % Ti for every 1 % Mo.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazards associated with the use of this test method see Practices E 50.

Standard Test Method for Determination of Titanium in Nickel Alloys by Diantipyrylmethane Molecular Absorption Spectrometric Method

ASTM E607-02 在氮气芬围中用点对面技术作铝合金的原子辐射光谱测定分析的标准试验方法

This test method is suitable for manufacturing control, for material or product acceptance, and for research and development. Its use over several years has shown precision and accuracy that are well within expected levels. It is assumed that all who use this test method will be trained analysts capable of performing laboratory procedures skillfully and safely, and that the work will be performed in a properly equipped laboratory.1.1 This test method covers the spectrochemical analysis of aluminum and aluminum alloys for the following elements in the concentration ranges indicated:ElementConcentration Range, %Silicon0.001 to 23.0Copper0.001 to 20.0Magnesium0.001 to 11.0Zinc0.001 to 10.0Tin0.001 to 7.5Nickel0.001 to 4.0Iron0.001 to 3.0Lithium0.0001 to 3.0Cobalt0.001 to 2.0Manganese0.001 to 2.0Chromium0.001 to 1.0Silver0.001 to 1.0Zirconium0.001 to 1.0Lead0.002 to 0.7Bismuth0.001 to 0.7Cadmium0.001 to 0.5Titanium0.001 to 0.5Beryllium0.0001 to 0.5Vanadium0.001 to 0.15Calcium0.001 to 0.05Gallium0.001 to 0.05Boron0.0001 to 0.05Sodium0.0001 to 0.051.2 The test method is applicable primarily to the control analysis of chill-cast samples. Other forms may be analyzed, provided that (1) they are sufficiently massive to prevent undue heating; (2) they permit machining flat surfaces having a minimum dimension of approximately 30 by 30 mm (1.2 in. by 1.2 in.); and (3) reference materials of similar metallurgical condition and chemical composition are available.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Atomic Emission Spectrometric Analysis Aluminum Alloys by the Point to Plane Technique Nitrogen Atmosphere

KS D ISO 1784:2001 铝合金.锌含量的测定.乙二胺四乙酸滴定法

이 규격은 카드뮴을 포함하지 않는 알루미늄 합금 중의 아연 측정을 위한 EDTA 적정 방법

Aluminium alloys-Determination of zinc-EDTA titrimetric method

KS D ISO 6827:2001 铝和铝合金.钛含量的测定.二安替比林基代甲烷光度法

이 규격은 알루미늄 및 알루미늄합금 중의 티타늄 분석 방법에 대한 디안티피릴메탄 분광법에

Aluminium and aluminium alloys－Determination of titanium content －Diantipyrylmethane photometric method