H26 金属无损检验方法 标准查询与下载

DIN EN ISO 9934-2:2015 无损检测.磁性粒子试验.第2部分:探测介质(ISO 9934-2-2015);德文版本EN ISO 9934-2-2015

Non-destructive testing - Magnetic particle testing - Part 2: Detection media (ISO 9934-2:2015); German version EN ISO 9934-2:2015

DIN EN ISO 9934-3:2015 无损检验.磁性粒子检验.第3部分:设备 (ISO 9934-3-2015);德文版本EN ISO 9934-3-2015

Non-destructive testing - Magnetic particle testing - Part 3: Equipment (ISO 9934-3:2015); German version EN ISO 9934-3:2015

DIN EN ISO 9934-1:2015 无损检验.磁性粒子检验.第1部分:一般原则(ISO 9934-1-2015);德文版本EN ISO 9934-1-2015

Non-destructive testing - Magnetic particle testing - Part 1: General principles (ISO 9934-1:2015); German version EN ISO 9934-1:2015

ISO 18563-3:2015 无损试验. 超声相控阵设备的特征和验证. 第3部分: 复合系统

This part of ISO 18563 addresses ultrasonic test systems implementing linear phased array probes, in contact (with or without wedge) or in immersion, with centre frequencies in the range of 0,5 MHz–10 MHz. It provides methods and acceptance criteria for verifying the performance of combined equipment (i.e. instrument, probe and cables connected). The methods described are suitable for users working under on-site or shop floor conditions. Its purpose is for the verification of the correct operation of the system prior to testing, and also the characterization of sound beams or verification of the absence of degradation of the system. The methods are not intended to prove the suitability of the system for particular applications, but are intended to prove the capability of the combined equipment to generate ultrasonic beams according to the settings used. The calibration of the system for a specific application is outside of the scope of part of ISO 18563 and it is intended that it be covered by the test procedure. This part of ISO 18563 does not address the following: — encircling arrays; — series of apertures having a different number of elements; — different settings for transmitting and receiving (e.g. active aperture, number of active elements, delays); — techniques using post-processing of the signals of individual elements in a more complex manner than a simple delay law (e.g. full matrix capture).

Non-destructive testing - Characterization and verification of ultrasonic phased array equipment - Part 3: Combined systems

NF A09-590-2*NF EN ISO 9934-2:2015 无损检验.磁粉检验.第2部分:检测介质

Non-destructive testing - Magnetic particle testing - Part 2 : detection media

NF A09-590-1:2015 无损检验.磁粉检验.第1部分:一般原则

Non-destructive testing - Magnetic particle testing - Part 1 : general principles

BS EN ISO 9934-1:2015 无损检验.磁粉检验.一般原则

Non-destructive testing. Magnetic particle testing. General principles

BS EN ISO 9934-3:2015 非破坏性测试 磁粉检测 设备

Non-destructive testing. Magnetic particle testing. Equipment

BS EN ISO 9934-2:2015 非破坏性测试 磁粉检测 介质检测

Non-destructive testing. Magnetic particle testing. Detection media

BS ISO 4993:2015 钢和铁铸件 射线照相测试

Steel and iron castings. Radiographic testing

ISO 4993:2015 钢铁铸件.X光线照相术检验

This International Standard specifies the general requirements for the radiography of steel and iron castings by means of X-rays or gamma-rays, in accordance with procedures given in ISO 5579

Steel and iron castings - Radiographic testing

ISO 9934-2:2015 无损检验.磁粒子试验.第2部分:检测介质

This partofISO 9934 specifies the Significant properties ofmagnetic particle testing products (including magnetic ink, powdeb carrier liquid, contrast aid paints) and the methods for checking their properties.

Non-destructive testing - Magnetic particle testing - Part 2: Detection media

ISO 9934-3:2015 无损检验.磁性粒子试验.第3部分:设备

This part of ISO 9934 describes three types of equipment for magnetic particle testing: — fixed installations; — specialized testing systems for testing components on a continuous basis, comprising a series of processing stations placed in sequence to form a process line. Equipment for magnetizing, demagnetizing, illumination, measurement, and monitoring are also described. This part of ISO 9934 specifies the properties to be provided by the equipment supplier, minimum requirements for application and the method of measuring certain parameters. Where appropriate, measuring and calibration requirements and in-service checks are also specified.

Non-destructive testing - Magnetic particle testing - Part 3: Equipment

ISO 9934-1:2015 无损检验.磁性粒子检验.第1部分：一般原则

Non-destructive testing - Magnetic particle testing - Part 1: General principles

JIS G 0582 AMD 1:2015 钢管的超声波探伤检验(修改件1)

Automated ultrasonic examination of steel pipes and tubes (Amendment 1)

BS EN ISO 18563-1:2015 无损试验. 超声相控阵设备的特征和验证. 仪器

Non-destructive testing. Characterization and verification of ultrasonic phased array equipment. Instruments

ISO 18490:2015 无损试验. NDT人员视力评估

This International Standard specifies the form of the optotype, the quality requirements for the chart, the test procedure, and the acceptance level for near vision acuity of NDT personnel. It also addresses the qualification requirements for personnel permitted to carry out the test. This International Standard only addresses near vision acuity under defined conditions similar to those encountered during routine NDT inspection. It does not address an individual’s overall visual acuity and users are advised to consider the need for a general eye examination by specialist medical personnel to ensure general vision acuity is appropriate for job function. This International Standard does not address colour vision requirements.

Non-destructive testing - Evaluation of vision acuity of NDT personnel

JIS G 0804:2015 焊接钢管焊缝用数字化射线检验

Digital radiographic examination for the weld seam of welded steel tubes

JIS G 0803:2015 焊接钢管焊缝用膜的射线检验

Radiographic examination with film for the weld seam of welded steel tubes

DIN EN 1330-1:2015 无损检验.专业术语.第1部分:一般术语表;三种语言版本EN 1330-1-2014

Non destructive testing - Terminology - Part 1: List of general terms; Trilingual version EN 1330-1:2014