共找到 1513 条与 金属无损检验方法 相关的标准,共 101 页
本标准规定了电网在役支柱瓷绝缘子及瓷套超声波检测方法和检测结果的评定。 本标准适用于发电厂、变电站(所)、换流站、串补站户内和户外外径不小于?80mm高压支柱瓷绝缘子及外径不小于?150mm的断路器、电流互感器、电压互感器(含电容式电压互感器)、避雷器等设备瓷质外套的超声波检测。 本标准也适用于发供电行业设备安装和检修时的检测。
Ultrasonic inspection for the trut porcelain insulator and borcelain bushing used in the grid system
本标准规定了铜及铜合金毛细管的穿过式涡流探伤方法,包括:术语和定义、涡流探伤原理和方法、涡流探伤系统、人工标准缺陷样管、探伤步骤、探伤结果的评定、探伤人员的一般要求及探伤报告。本标准适用于铜及铜合金毛细管的规格范围:外径(Φ0.5~Φ6.1)×内径(Φ0.3~Φ4.45)。其他规格毛细管可参照本标准执行。
Capillary tube of copper and copper alloy-eddy current testing method
本标准规定了铜及铜合金管材的超声波纵波探伤方法。本标准适用于A型脉冲纵波反射法对壁厚与外径比≥0.2的铜及铜合金管材的超声波探伤。
Longitudinal wave method of ultrasonic inspection for copper and copper alloys tubes
Non-destructive testing - Ultrasonic testing - Technique of testing claddings produced by welding, rolling and explosion (ISO 17405:2014); German version EN ISO 17405:2014
Non-destructive testing - Penetrant testing - Part 1: General principles (ISO 3452-1:2013, Corrected version 2014-05-01); German version EN ISO 3452-1:2013
La présente Norme internationale spécifie les techniques d'essai manuel par ultrasons des revêtements sur acier appliqués par soudage, laminage et explosion en utilisant des traducteurs mono-éléments ou à émetteur et récepteur séparés.L'essai est destiné à couvrir la détection des discontinuités à 2 ou 3 dimensions présentes dans le revêtement et la région d'interface.La présente Norme internationale ne fournit pas de critères d'acceptation et ne définit pas l'étendue des essais.
Non-destructive testing - Ultrasonic testing - Technique of testing claddings produced by welding, rolling and explosion
Steel products. Employer's qualification system for non-destructive testing (NDT) personnel
Non-destructive testing. Ultrasonic testing. Technique of testing claddings produced by welding, rolling and explosion
Non-destructive testing - Ultrasonic testing - General principles (ISO 16810:2012); German version EN ISO 16810:2014
Non-destructive testing - Ultrasonic testing - Transmission technique (ISO 16823:2012); German version EN ISO 16823:2014
Dieses Internationale Norm legt Techniken fur die manuelle Ultraschallprufung von Plattierungen auf Stahl fest, die durch Schweisen, Walzen und Sprengen aufgetragen wurden, unter Verwendung von Sende-Empfangs-Prufkopfen (SE-Prufkopfen) oder Einzelelement-Prufkopfen. Die Prufung ist dafur vorgesehen, den Nachweis von zweidimensionalen oder dreidimensionalen Inhomogenitaten in der Plattierung und in der Grenzschicht zu erbringen. In dieser Internationalen Norm werden weder Zulassigkeitskriterien angegeben noch wird der Prufumfang festgelegt.
Non-destructive testing - Ultrasonic testing - Technique of testing claddings produced by welding@ rolling and explosion
Method and acceptance criteria of ultrasonic examination for gas pressure welds of deformed steel bars for concrete reinforcement
This report identifies, prioritizes and addresses technology gaps in the ASME Pressure Technology Codes and Standards. A key component of this project was to review an extensive selection of current Codes and Standards which relate to power boilers and develop guidelines for component design and flaw acceptance criteria. The main focus of this project is to evaluate the current state of understanding with regard to creep-fatigue interaction for intended boiler materials to support the development of effective Design-By-Analysis (DBA) rules.
DESIGN GUIDELINES FOR THE EFFECTS OF CREEP, FATIGUE & CREEP-FATIGUE INTERACTION WITH DESIGN-BY-ANALYSIS AND NONDESTRUCTIVE INSPECTION ACCEPTANCE CRITERIA
Non-destructive testing - Ultrasonic testing - Sensitivity and range setting (ISO 16811:2012); German version EN ISO 16811:2014
Non-destructive testing - Ultrasonic testing - Time-of-flight diffraction technique as a method for detection and sizing of discontinuities (ISO 16828:2012); German version EN ISO 16828:2014
Non-destructive testing - Ultrasonic testing - Characterization and sizing of discontinuities (ISO 16827:2012); German version EN ISO 16827:2014
Non-destructive testing - Characterisation and verification of ultrasonic phased array equipment - Part 2: Probes; German version EN 16392-2:2014
Non-destructive testing - Ultrasonic testing - Examination for discontinuities perpendicular to the surface (ISO 16826:2012); German version EN ISO 16826:2014
La présente Norme internationale définit les principes généraux du contrôle par les techniques du tandem et des ondes longitudinales et longitudinales-transversales (LLT) pour la détection des discontinuités perpendiculaires à la surface.
Non-destructive testing - Ultrasonic testing - Examination for discontinuities perpendicular to the surface
La présente Norme internationale définit les principes généraux du contrôle ultrasonore des produits industriels perméables aux ondes ultrasonores.Les conditions particulières d'application et d'utilisation des contrôles ultrasonores, qui dépendent du type de produit examiné, font l'objet de documents tels que :- normes de produit ;- spécifications ;- codes ;- documents contractuels ;- procédures écrites.Sauf indications contraires dans les documents de référence, les exigences minimales de la présente Norme internationale sont applicables.La présente Norme internationale ne définit pas :- l'étendue des essais et des plans de contrôle ;- de critères d'accep
Non-destructive testing - Ultrasonic testing - General principles
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号