H26 金属无损检验方法 标准查询与下载
共找到 1513 条与 金属无损检验方法 相关的标准，共 101 页
警告：使用本标准的人员应具有正规实验室工作的实践经验。本标准并未指出所有可能的安全问题。使用者应随时关好X射线衍射仪的防护罩（或门），防止X射线散射。 本部分规定了采用X射线衍射法鉴定金属矿产类进口固体废物物相的通则。 本部分适用于采用X射线衍射法对金属矿产类进口固体废物进行的物相鉴定。
Identification of import solid waste ralated with metal minerals by X-ray diffraction.Part 1:General rules
- ICS
- CCS
- H26
- 发布
- 2011-09-09
- 实施
- 2012-04-01
Non-destructive testing - Thermographic testing - Part 2: Equipment
- ICS
- 19.100
- CCS
- H26
- 发布
- 2011-09
- 实施
This specification covers the procedure for ultrasonic inspection of wrought titanium and titanium alloy products 0.25 inch (6.4 mm) and over in cross-sectional (thickness) or diameter. When specifically requested by purchaser, this specification may be used for metals other than titanium. This procedure has been used typically for locating internal defects, such as cracks, voids, spongy areas, and other structural discontinuities, which may or may not be exposed to the surface, but usage is not limited to such applications.
Ultrasonic Inspection, Titanium and Titanium Alloy Bar, Billet and Plate
- ICS
- 49.025.30
- CCS
- H26
- 发布
- 2011-07-22
- 实施
This part of ISO 10893 specifies requirements for the automated full peripheral ultrasonic testing of seamless and welded steel tubes, with the exception of submerged arc welded (SAW) tubes, for wall thickness measurement. It specifies the testing method and corresponding calibration procedures.
Non-destructive testing of steel tubes - Part 12: Automated full peripheral ultrasonic thickness testing of seamless and welded (except submerged arc-welded) steel tubes (ISO 10893-12:2011); German version EN ISO 10893-12:2011
- ICS
- 23.040.10;77.040.20
- CCS
- H26
- 发布
- 2011-07
- 实施
This part of ISO 10893 specifies requirements for automated eddy current testing of seamless and welded tubes with the exception of submerged arc-welded (SAW) tubes, for the detection of imperfections according to the different acceptance levels as shown in Tables 1 and Table 2. It is applicable to the inspection of tubes with an outside diameter greater than or equal to 4 mm.
Non-destructive testing of steel tubes - Part 2: Automated eddy current testing of seamless and welded (except submerged arc-welded) steel tubes for the detection of imperfections (ISO 10893-2:2011); German version EN ISO 10893-2:2011
- ICS
- 23.040.10;77.040.20
- CCS
- H26
- 发布
- 2011-07
- 实施
This Part of ISO 10893 specifies the requirements for film based radiographic X-ray testing of the longitudinal or helically (spiral) weld seams of automated fusion arc welded steel tubes for the detection of imperfections.
Non-destructive testing of steel tubes - Part 6: Radiographic testing of the weld seam of welded steel tubes for the detection of imperfections (ISO 10893-6:2011); German version EN ISO 10893-6:2011
- ICS
- 23.040.10;77.040.20
- CCS
- H26
- 发布
- 2011-07
- 实施
This part of ISO 10893 specifies requirements for the automated ultrasonic testing of strip/plate used in the manufacture of welded tubes for the detection of laminar imperfections carried out in the pipe mill before or during pipe production.
Non-destructive testing of steel tubes - Part 9: Automated ultrasonic testing for the detection of laminar imperfections in strip/plate used for the manufacture of welded steel tubes (ISO 10893-9:2011); German version EN ISO 10893-9:2011
- ICS
- 23.040.10;77.040.20
- CCS
- H26
- 发布
- 2011-07
- 实施
This part of ISO 10893 specifies requirements applicable to liquid penetrant testing of seamless and welded tubes for the detection of surface imperfections. It is applicable to all or any part of the tube surface as required by the relevant product standards. It can also be applicable to the testing of hollow sections.
Non-destructive testing of steel tubes - Part 4: Liquid penetrant inspection of seamless and welded steel tubes for the detection of surface imperfections (ISO 10893-4:2011); German version EN ISO 10893-4:2011
- ICS
- 23.040.10;77.040.20
- CCS
- H26
- 发布
- 2011-07
- 实施
This part of ISO 10893 specifies requirements for automated ultrasonic testing for the detection of laminar imperfections a) in the pipe body (full peripheral testing) of seamless and welded, except submerged arc welded (SAW) steel tubes, or b) in the area adjacent to the weld seam of welded steel tubes. and optionally c) at the ends (full peripheral testing) of seamless and welded tubes.
Non-destructive testing of steel tubes - Part 8: Automated ultrasonic testing of seamless and welded steel tubes for the detection of laminar imperfections (ISO 10893-8:2011); German version EN ISO 10893-8:2011
- ICS
- 23.040.10;77.040.20
- CCS
- H26
- 发布
- 2011-07
- 实施
This part of ISO 10893 specifies requirements for automated electromagnetic testing of seamless and welded steel tubes, with the exception of submerged arc-welded (SAW) tubes, for verification of hydraulic leak-tightness in substitution of hydrostatic test. It is applicable to the inspection of tubes with an outside diameter greater than or equal to 4 mm, when testing with eddy current, and greater than 10 mm when testing with flux leakage method.
Non-destructive testing of steel tubes - Part 1: Automated electromagnetic testing of seamless and welded (except submerged arc-welded) steel tubes for the verification of hydraulic leaktightness (ISO 10893-1:2011); German version EN ISO 10893-1:2011
- ICS
- 23.040.10;77.040.20
- CCS
- H26
- 发布
- 2011-07
- 实施
This part of ISO 10893 specifies the requirements for digital radiographic X-ray testing by either computed radiography (CR) or radiography with digital detector arrays (DDA), of the longitudinal or helically (spiral) weld seams of automatic fusion arc-welded steel tubes for the detection of imperfections. The standard specifies acceptance levels and calibration procedures.
Non-destructive testing of steel tubes - Part 7: Digital radiographic testing of the weld seam of welded steel tubes for the detection of imperfections (ISO 10893-7:2011); German version EN ISO 10893-7:2011
- ICS
- 23.040.10;77.040.20
- CCS
- H26
- 发布
- 2011-07
- 实施
This part of ISO 10893 specifies requirements for the ultrasonic testing of the weld seam of longitudinally or helically submerged arc-welded (SAW), or electric resistance and induction welded (EW) steel tubes. For SAW tubes, the inspection covers the detection of imperfections oriented predominantly parallel to and/or, by agreement, perpendicular to the weld seam or both. For EW tubes, the inspection covers the detection of imperfections oriented predominantly parallel to the weld seam. In the case of testing on logitudinal imperfections, Lamb wave testing can be applied at the discretion of the manufacturer. For the detection of imperfections at weld seam of EW tubes, full peripheral ultrasonic testing is accepted. This part of ISO 10893 can also be applicable to the testing of circular hollow sections.
Non-destructive testing of steel tubes - Part 11: Automated ultrasonic testing of the weld seam of welded steel tubes for the detection of longitudinal and/or transverse imperfections (ISO 10893-11:2011); German version EN ISO 10893-11:2011
- ICS
- 23.040.10;77.040.20
- CCS
- H26
- 发布
- 2011-07
- 实施
This part of ISO 10893 specifies requirements for magnetic particle inspection of seamless and welded ferromagnetic steel tubes for the detection of surface imperfections on the tube body and the end/bevel face at the ends.
Non-destructive testing of steel tubes - Part 5: Magnetic particle inspection of seamless and welded ferromagnetic steel tubes for the detection of surface imperfections (ISO 10893-5:2011); German version EN ISO 10893-5:2011
- ICS
- 23.040.10;77.040.20
- CCS
- H26
- 发布
- 2011-07
- 实施
This part of ISO 10893 specifies requirements for automated full peripheral magnetic flux leakage testing of seamless and welded ferromagnetic steel tubes, with the exception of submerged arc-welded (SAW) tubes, for the detection of imperfections.
Non-destructive testing of steel tubes - Part 3: Automated full peripheral flux leakage testing of seamless and welded (except submerged arc-welded) ferromagnetic steel tubes for the detection of longitudinal and/or transverse imperfections (ISO 10893-3:2
- ICS
- 23.040.10;77.040.20
- CCS
- H26
- 发布
- 2011-07
- 实施
This part of ISO 10893 specifies requirements for automated full peripheral ultrasonic shear wave (generated by conventional or phased array technique) testing of seamless and welded (except submerged arc-welded) steel tubes, for the detection of longitudinal and/or transversal imperfections. Unless otherwise specified in the purchase order, the testing method is applied for the detection of predominantly longitudinal imperfections. In the case of testing on longitudinal imperfections, Lamb wave testing may be applied at the discretion of the manufacturer. For seamless tubes, by agreement between purchaser and manufacturer, testing principles of this international standard may be applied to detect imperfections having other orientations. This part of ISO 10893 is applicable to the inspection of tubes with an outside diameter greater than or equal to 10 mm, normally with an outside diameter-to-thickness ratio greater or equal to 5. This part of ISO 10893 can also be applicable to the testing of circular hollow sections.
Non-destructive testing of steel tubes - Part 10: Automated full peripheral ultrasonic testing of seamless and welded (except submerged arc-welded) steel tubes for the detection of longitudinal and/or transverse imperfections (ISO 10893-10:2011); German v
- ICS
- 23.040.10;77.040.20
- CCS
- H26
- 发布
- 2011-07
- 实施
Non-destructive testing of steel tubes - Part 7 : digital radiographic testing of the weld seam of welded steel tubes for the detection of imperfections.
- ICS
- 23.040.10;77.040.20
- CCS
- H26
- 发布
- 2011-05-01
- 实施
- 2011-05-27
Non-destructive testing of steel tubes - Part 3 : automated full peripheral flux leakage testing of seamless and welded (except submerged arc-welded) ferromagnetic steel tubes for the detection of longitudinal and/or transversal imperfections.
- ICS
- 23.040.10;77.040.20
- CCS
- H26
- 发布
- 2011-05-01
- 实施
- 2011-05-27
Non-destructive testing of steel tubes - Part 2 : automated eddy current testing of seamless and welded (except submerged arc-welded) steel tubes for the detection of imperfections.
- ICS
- 23.040.10;77.040.20
- CCS
- H26
- 发布
- 2011-05-01
- 实施
- 2011-05-27
Non-destructive testing of steel tubes - Part 6 : radiographic testing of the weld seam of welded steel tubes for the detection of imperfections.
- ICS
- 23.040.10;77.040.20
- CCS
- H26
- 发布
- 2011-05-01
- 实施
- 2011-05-27
Non destructive testing of steel tubes - Part 12 : automated full peripheral ultrasonic thickness testing of seamless and welded (except submerged arc-welded) steel tubes.
- ICS
- 23.040.10;77.040.20
- CCS
- H26
- 发布
- 2011-05-01
- 实施
- 2011-05-27
