H40 钢铁产品综合 标准查询与下载

DIN EN 10269 Berichtigung 3:2009 规定高温和/或低温性能的紧固件用钢及镍合金.技术勘误DIN EN 10269-2006

Steels and nickel alloys for fasteners with specified elevated and/or low temperature properties; German version EN 10269:1999 + A1:2006, Corrigendum to DIN EN 10269:2006; German version EN 10269:1999/A1:2006/AC:2008

BS EN 10088-5:2009 不锈钢.建筑用防腐蚀钢的棒材、杆材、线材、型材和光亮产品的技术交付条件

1.1 The scope of this part of EN 10088 is to specify the technical delivery conditions for hot or cold formed bars, rods, wire, sections and bright products of standard and special grades of corrosion resisting stainless steels for construction purposes in addition to the general technical delivery conditions specified in EN 10021. 1.2 This European Standard does not apply to components manufactured by further processing of the product forms listed in 1.1 with quality characteristics altered as a result of such further processing.

Stainless steels - Part 5: Technical delivery conditions for bars, rods, wire, sections and bright products of corrosion resisting steels for construction purposes

BS EN 10343:2009 建筑用淬火和回火钢.技术交货条件

This document specifies the technical delivery requirements for the following steel products intended for use in the construction industry: bars (including hammer-forged bars); wide flats; hot-rolled strip and sheet/plate; forgings. They are manufactured from the direct hardening non alloy steels for quenching and tempering and the direct hardening alloy steels for quenching and tempering and supplied in one of the heat treatment conditions given for the different types of products in Table 1. These steels are generally intended for the manufacture of quenched and tempered parts, but can also be used in the normalized condition. The requirements for mechanical properties are restricted to part sizes given in Tables 4 and 5. NOTE 1 In accordance with EN 10020, the steels covered by this standard are quality and special steels. The differences between quality and special steels are characterized by the following requirements, which are valid for special steels only:  the minimum impact values in the quenched and tempered condition (for non alloy special steels in the case of mean percentages by mass of carbon < 0,50 % only);  limited oxide inclusion content;  lower maximum contents for phosphorus and sulphur. NOTE 2 This standard does not apply for bright steel products. NOTE 3 This standard only applies for the manufacture of products without any further cold or hot forming and no additional heat treatment, i.e. the properties are according to the delivery condition (+N, +QT). In addition to the specifications of this European Standard, the general technical delivery conditions given in EN 10021 will be applicable unless otherwise specified.

Steels for quenching and tempering for construction purposes - Technical delivery conditions

SANS 50025-6:2009 热轧结构钢产品.第6部分:在淬火及回火条件下高屈服强度的结构钢扁平材交货技术条件

Specifies requirements for flat products of high yield strength alloy special steels. The grades and qualities are given in chemical composition tables and mechanical properties tables and are supplied in the quenched and tempered condition.

Hot rolled products of structural steels Part 6: Technical delivery conditions for flat products of high yield strength structural steels in the quenched and tempered condition

KS D 3859-2009 热成形钢材

이 표준은 열간 단조 후 공랭 또는 제어 냉각에 의해서 최종 제품의 템퍼링을 생략할 수 있

Micro alloyed steels for hot forging

KS D 3606-2009 围墙用铁柱

이 표준은 울타리용 철주(이하 철주라 한다.)에 대하여 규정한다.

Drive-type spadeless fence post

KS D 3596-2009 有色锌涂层钢丝

이 표준은 주로 마름모형 철망에 사용되는 착색 도장 아연 도금 철선(이하 도장선이라 한다.

Precoated color zinc-coated steel wires

JIS G 2402:2009 钢铁制造用铝废渣

This Japanese Industrial Standard specifies the aluminium dross to be used as the flux for making iron and steel (hereafter referred to as aluminium dross)

Aluminium dross for iron and steel making

JIS G 0203:2009 钢和铁用术语集(产品和质量)

This Standard specifies the principal terms and their definitions related to the products and their qualities for each use of the rolled,cast or forged steels.

Glossary of terms used in iron and steel (Products and quality)

SANS 50025-2:2009 热轧结构钢产品.第2部分:非合金结构钢交货技术条件

Specifies the technical delivery conditions for flat and long products and semi-finished products which are meant for further processing to flat and long products of hot rolled non-alloy quality steels in the grades and qualities given in chemical compos

Hot rolled products of structural steels Part 2: Technical delivery conditions for non-alloy structural steels

SANS 50025-4:2009 热轧结构钢产品.第4部分:热机械轧制可焊接细纹理结构钢交货技术条件

Specifies requirements for flat and long products of hot rolled weldable fine grain structural steels in the thermomechanical rolled condition in the grades and qualities given in chemical composition tables and mechanical properties tables in thicknesse

Hot rolled products of structural steels Part 4: Technical delivery conditions for thermomechanical rolled weldable fine grain structural steels

KS D 3573-2009 管道用合金钢管

이 표준은 주로 고온도의 배관에 사용하는 합금강 강관(이하 관이라 한다.)에 대하여 규정한

Alloy steel pipes

KS D 3588-2009 排管用焊接大口径不锈钢钢管

이 표준은 내식용, 저온용, 고온용 등의 배관에 사용하는 용접 대구경 스테인리스 강관(이하

Large diameter welded stainless steel pipes

KS D 3562-2009 压力排管用碳素钢管

이 표준은 350 ℃ 정도 이하에서 사용하는 압력 배관에 쓰이는 탄소 강관(이하 관이라 한

Carbon steel pipes for pressure service

KS D 3564-2009 高压排管用碳素钢管

이 표준은 350 ℃ 정도 이하에서 사용 압력이 높은 배관에 사용하는 탄소 강관(이하 관이

Carbon steel pipes for high pressure service

SANS 907:2009 机构用不锈钢

Covers material, dimensional, and constructional requirements for stainless steel crockery sinks with draining boards and stainless steel pot sinks, for use in institutions.

Stainless steel sinks for institutional use

SANS 50025-5:2009 热轧结构钢产品.第5部分:改进的防大气腐蚀性的结构钢交货技术条件

Specifies requirements for flat and long products of hot rolled steels with improved atmospheric corrosion resistance in the grades and qualities given in tables 2 and 3 (chemical composition) and tables 4 and 5 (mechanical properties) in the usual deliv

Hot rolled products of structural steels Part 5: Technical delivery conditions for structural steels with improved atmospheric corrosion resistance

SANS 50025-1:2009 热轧结构钢产品.第1部分:交货的一般技术条件

Specifies the general delivery conditions and requirements for flat and long products of hot rolled structural steels excluding structural hollow sections and tubes.

Hot rolled products of structural steels Part 1: General technical delivery conditions

SANS 50025-3:2009 热轧结构钢产品.第3部分:标准化/标准化轧制可焊接细纹理结构钢交货技术条件

Specifies requirements for flat and long products of hot rolled weldable fine grain structural steels in the normalized/normalized rolled delivery condition in the grades and qualities given in the chemical composition and mechanical properties tables.

Hot rolled products of structural steels Part 3: Technical delivery conditions for normalized/normalized rolled weldable fine grain structural steels

SAE J404-2009 SAE合金钢的化学成分

In 1941, the SAE Iron and Steel Division in collaboration with the American Iron and Steel Institute (AISI) made a major change in the method of expressing composition ranges for the SAE steels. The plan, as now applied, is based in general on narrower ladle analysis ranges plus certain product (check) analysis allowances on individual samples, in place of the fixed ranges and limits without tolerances formerly provided for carbon and other elements in SAE steels (reference SAE J408). ISTC Division 1 has developed a procedure which allows for the maintenance of the grade list in this SAE Standard. This will involve conducting an industry-wide survey to solicit input. This survey will be conducted at a frequency deemed necessary by the technical committee. Criteria have been established for the addition to or deletion of grades from the grade table. A new grade will be considered if it meets standard SAE grade ranges, has a minimum usage or production of 225 tonnes/year (250 tons/year), and has the endorsement of at least two users or producers. New steel compositions will still be considered as Potential Standard (PS) steels, based on the guidelines provided in SAE J1081, until such time as production of the new steel achieves a level of production or usage qualifying it for consideration as a standard steel. The deletion of a grade from the grade table will be by consensus based on the grade survey results. Deleted grades will be archived in SAE J1249 for future reference. The compositions in this document may apply to open hearth and basic oxygen, or electric furnace steels. Grades shown in Table 1 with prefix letter E are normally made by the electric furnace process with maximum limits of 0.025% phosphorus and 0.025% sulfur. The nominal chemical limits or ranges in the compositions given in Table 1 are subject to standard variations in check analysis given in SAE J409. Since AISI is no longer issuing steel grade designations, all grades listed in this document are SAE grades.

Chemical Compositions of SAE Alloy Steels