H40 钢铁产品综合 标准查询与下载

ASME BPVC Section 2 Part A Addenda 2009-2009 ASME锅炉及压力容器规程.第2节:材料.第A部分:有色金属材料规范(从开始至SA-450),补遗2009b,2009年7月1日

ASME Boiler & Pressure Vessel Code - Section 2: Materials - Part A: Ferrous Material Specifications (Beginning to SA-450); 2009b Addenda July 1, 2009

DIN EN 10083-3 Berichtigung 1:2009 淬火和回火钢.第3部分:合金钢的交货技术条件.技术勘误DIN EN 10083-3-2007

Steels for quenching and tempering - Part 3: Technical delivery conditions for alloy steels; German version EN 10083-3:2006, Corrigendum to DIN EN 10083-3:2007-01; German version EN 10083-3:2006/AC:2008

ASTM A90/A90M-09 带有锌或锌合金涂层的钢铁上的涂层重量[质量]的标准试验方法

This test method provides a standard method for determining the weight [mass] of coating for comparison with specification requirements. A coating of zinc on iron or steel articles provides protection against corrosion. As the protection is provided by sacrificial loss of zinc, the degree of protection is proportional to the weight [mass] of zinc coating. Specifications for zinc-coated articles frequently provide for different classes of coating so that the purchaser can select the coating weight [mass] most suitable to his needs. 1.1 This test method covers procedures for determining the weight [mass] of coating on iron or steel sheet, wire, and other articles in which the coating is zinc or a zinc alloy, such as zinc-5 % aluminum (including zinc-5 % aluminum-mischmetal and zinc-5 % aluminum-0.1 % magnesium) or 55 % aluminum-zinc. In the body of this test method, reference to zinc coating shall be interpreted to also include zinc alloy coating except where specifically stated otherwise. 1.2 The final results determined by this test method shall be expressed in inch-pound units or SI units, depending on the units used in the material specification to which the results are to be compared. Certain portions of the procedure involving determination of specimen weight [mass] have traditionally been performed in SI units, and corresponding inch-pound units are not included. 1.3 For sheet products, the final results are expressed as either coating weight [mass] total both sides, or coating weight [mass] separately on each side, depending on the specified requirements. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazards statements see 5.1.

Standard Test Method for Weight [Mass] of Coating on Iron and Steel Articles with Zinc or Zinc-Alloy Coatings

ASTM A959-09 锻制不锈钢用说明协调标准等级构成的标准指南

It is anticipated that the ASTM Subcommittees A01.06, A01.10, A01.17, A01.22, and A01.28 will use the standard composition limits listed in this guide for the grades identified by the corresponding UNS designation in the product specification unless there is a specific technical justification for doing otherwise. The compositions in this guide shall not be considered as chemical requirements for any particular product until adopted by the subcommittee overseeing that product. Assuming that uniform compositions among the many product standards for stainless steel are desirable, the composition limits provided in this standard are to be used as guides in determining limits for each of the elements included in the total composition of each grade. The composition limits have been established with the intent that each product subcommittee will find it necessary to require only a minimum number of changes to reflect specific technical effects. Section 5 lists the general guidelines followed for determining the limits for each element; the limits established in this guide are based on these guidelines. Not included in this standard stainless steel grade harmonization effort is an attempt to unify stainless steel compositions in ASTM product standards by any means other than recognizing current industry practices. 1.1 This guide provides a guide to ASTM Subcommittees A01.06, A01.10, A01.17, A01.22, and A01.28 for specifying chemical composition limits of wrought stainless steels. It is intended that these recommended grade composition limits be suitable for adoption by other standardization bodies that prepare standards for stainless steel products. 1.2 Included in this guide are the recommendations for determining the number of significant figures for specifying chemical composition from Test Methods, Practices, and Terminology A 751. 1.3 All stainless steel UNS numbers and the stainless steel grades in all standards overseen by the aforementioned ASTM subcommittees have been included, except those grades applicable to restricted special end uses and alloys containing less than 10.5 % minimum chromium. 1.4 Not addressed are minor composition modifications which a specific product subcommittee may find necessary to accommodate effects of normal processing or to enhance fabricability by the producer or user, or both. 1.5 Also not generally addressed (except when established by ASTM product subcommittees) is a complete rationalization of all limits, especially when such would conflict with long-standing practices and is not justified by special technical effect. 1.6 Excluded from this guide are cast material and welding filler metal.

Standard Guide for Specifying Harmonized Standard Grade Compositions for Wrought Stainless Steels

ASTM A534-09 耐摩轴承用渗碳钢的标准规范

1.1 This specification covers the requirements for carburizing bearing-quality steel to be used in the manufacture of anti-friction bearings. 1.2 Supplementary requirements of an optional nature are provided and when desired shall be so stated in the order. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

Standard Specification for Carburizing Steels for Anti-Friction Bearings

ASTM A866-09 耐磨中碳轴承钢的标准规范

1.1 This specification covers medium carbon bearing quality steel to be used in the manufacture of anti-friction bearings. 1.2 Supplementary requirements of an optional nature are provided and when desired shall be so stated in the order. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

Standard Specification for Medium Carbon Anti-Friction Bearing Steel

ASTM A485-09 高淬硬性耐磨轴承钢标准规范

1.1 This specification covers high hardenability modifications of high-carbon bearing quality steel to be used in the manufacture of antifriction bearings. 1.2 Supplementary requirements of an optional nature are provided and when desired shall be so stated in the order. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

Standard Specification for High Hardenability Antifriction Bearing Steel

ASTM A756-09 耐磨不锈轴承钢的标准规范

1.1 This specification covers the requirements for chromium-carbon bearing quality stainless steel to be used in the manufacture of anti-friction bearings. 1.2 Supplementary Requirements of an optional nature are provided and when desired shall be so stated in the order. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

Standard Specification for Stainless Anti-Friction Bearing Steel

ASTM A892-09(2014)e1 高碳轴承钢微观结构的定义和等级的标准指南

1.1 This guide covers the description of carbide structures in annealed high carbon bearing steels. 1.2 Included is a guide for rating steel specimens by a graded series of photomicrographs showing the incidence of certain conditions. 1.3 The reference photomicrographs are graded illustrations of annealed carbides categorized by size, network, and lamellar content (shape). 1.4 This guide is to facilitate communication and description of microstructure. It does not establish limits of acceptability. Such limits are a matter of agreement between user and producer. 1.5 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Guide for Defining and Rating the Microstructure of High Carbon Bearing Steels

ASTM A892-09 高碳轴承钢微观结构的定义和等级的标准指南

1.1 This guide covers the description of carbide structures in annealed high carbon bearing steels. 1.2 Included is a guide for rating steel specimens by a graded series of photomicrographs showing the incidence of certain conditions. 1.3 The reference photomicrographs are graded illustrations of annealed carbides categorized by size, network, and lamellar content (shape). 1.4 This guide is to facilitate communication and description of microstructure. It does not establish limits of acceptability. Such limits are a matter of agreement between user and producer. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Guide for Defining and Rating the Microstructure of High Carbon Bearing Steels

ASTM A994-09 钢,不锈钢及相关合金的产品规范编辑程序和格式指南

The Form and Style Manual provides mandatory requirements and recommended practices for the preparation and content of ASTM specifications. In order to promote consistency in the style and content of product specifications under its jurisdiction, Committee A01 recognizes the need to provide a supplementary document pertaining to the types of products and materials covered by those specifications. This guide contains a list of sections to be considered for inclusion in a specification for steel, stainless steel, and related alloy products, and guidance or recommended wording, or both, for such sections. Persons drafting new product specifications, or modifying existing ones, under the jurisdiction of Committee A01, should follow this guide and the requirements of the Form and Style Manual to ensure consistency.1.1 This guide covers the editorial form and style for product specifications under the jurisdiction of ASTM Committee A01. Note 18212;For standards other than product specifications, such as test methods, practices, and guides, see the appropriate sections of Form and Style for ASTM Standards (Blue Book). 1.2 Subcommittees preparing new product specifications or revising existing ones should follow the practices and procedures outlined herein, and be guided by the latest specification covering similar commodities. 1.3 This guide has been prepared as a supplement to the current edition of the Form and Style Manual, and is appropriate for use by the subcommittees to Committee A01. This guide is to be applied in conjunction with the Form and Style Manual. 1.4 If a conflict exists between this guide and the mandatory sections of the current edition of the Form and Style Manual, the Form and Style Manual requirements have precedence. If a conflict exists between this guide and the nonmandatory sections of the current edition of the Form and Style Manual, the guide has precedence. 1.5 When patents are involved, the specifications writer should refer to section F3 of the Form and Style Manual. Also, refer to part F of the Form and Style Manual for trademark information and the safety hazards caveat.

Standard Guide for Editorial Procedures and Form of Product Specifications for Steel, Stainless Steel, and Related Alloys

ASTM A153/A153M-09 钢铁五金器具镀锌(热浸)的标准规范

1.1 This specification covers zinc coatings applied by the hot-dip process on iron and steel hardware. The hot-dip galvanizing process consists of parts being immersed in molten zinc for a sufficient time to allow a metallurgical reaction between iron from the steel surface and the molten zinc, resulting in the formation of Zn/Fe alloy layers bonding the coating to the steel surface. 1.2 This specification is intended to be applicable to hardware items that are centrifuged or otherwise handled to remove excess galvanizing bath metal (free zinc). Coating thickness grade requirements reflect this. 1.3 This specification is applicable to orders in either inch-pound units (as A 153) or in SI units (as A 153M). Inch-pound units and SI units are not necessarily exact equivalents. Within the text of this specification and where appropriate, SI units are shown in brackets. Each system shall be used independently of the other without combining values in any way. In the case of orders in SI units, all testing and inspection shall be done using the metric equivalent of the test or inspection method as appropriate. In the case of orders in SI units, such shall be stated to the galvanizer when the order is placed. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Zinc Coating (Hot-Dip) on Iron and Steel Hardware

ASTM A295/A295M-09 高碳耐磨轴承钢标准规范

1.1 This specification covers high-carbon bearing-quality steel to be used in the manufacture of anti-friction bearings. 1.2 Supplementary requirements of an optional nature are provided and when desired shall be so stated in the order. 1.3 The values stated in either inch-pound units or SI units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other.

Standard Specification for High-Carbon Anti-Friction Bearing Steel

ASTM A653/A653M-09a 热浸镀锌法生产的锌镀层(镀锌)或锌,铁合金镀层(合金化热镀锌)钢板标准规范

1.1 This specification covers steel sheet, zinc-coated (galvanized) or zinc-iron alloy-coated (galvannealed) by the hot-dip process in coils and cut lengths. 1.2 The product is produced in various zinc or zinc-iron alloy-coating weights [masses] or coating designations as shown in Table 1and in Table S2.1. 1.3 Product furnished under this specification shall conform to the applicable requirements of the latest issue of Specification A924/A924M, unless otherwise provided herein. 1.4 The product is available in a number of designations, grades and classes in four general categories that are designed to be compatible with different application requirements. 1.4.1 Steels with mandatory chemical requirements and typical mechanical properties. 1.4.2 Steels with mandatory chemical requirements and mandatory mechanical properties. 1.4.3 Steels with mandatory chemical requirements and mandatory mechanical properties that are achieved through solid-solution or bake hardening. 1.5 This specification is applicable to orders in either inch-pound units (as A653) or SI units (as A653M). Values in inch-pound and SI units are not necessarily equivalent. Within the text, SI units are shown in brackets. Each system shall be used independently of the other. 1.6 Unless the order specifies the “M” designation (SI units), the product shall be furnished to inch-pound units. 1.7 The text of this specification references notes and footnotes that provide explanatory material. These notes and footnotes, excluding those in tables and figures, shall not be considered as requirements of this specification. 1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Steel Sheet, Zinc-Coated (Galvanized) or Zinc-Iron Alloy-Coated (Galvannealed) by the Hot-Dip Process

ASTM A123/A123M-09 镀锌(热浸镀锌)钢铁产品的标准规范

1.1 This specification covers the requirements for zinc coating (galvanizing) by the hot-dip process on iron and steel products made from rolled pressed and forged shapes, castings, plates, bars, and strips. 1.2 This specification covers both unfabricated products and fabricated products, for example, assembled steel products, structural steel fabrications, large tubes already bent or welded before galvanizing, and wire work fabricated from uncoated steel wire. This specification also covers steel forgings and iron castings incorporated into pieces fabricated before galvanizing or which are too large to be centrifuged (or otherwise handled to remove excess galvanizing bath metal). Note 18212;This specification covers those products previously addressed in Specifications A 123-78 and A 386-78. 1.3 This specification does not apply to wire, pipe, tube, or steel sheet which is galvanized on specialized or continuous lines, or to steel less than 22 gage (0.0299 in.) [0.76 mm] thick. 1.4 The galvanizing of hardware items that are to be centrifuged or otherwise handled to remove excess zinc (such as bolts and similar threaded fasteners, castings and rolled, pressed and forged items) shall be in accordance with Specification A 153/A 153M. 1.5 Fabricated reinforcing steel bar assemblies are covered by the present specification. The galvanizing of separate reinforcing steel bars shall be in accordance with Specification A 767/A 767M. 1.6 This specification is applicable to orders in either inch-pound units (as A 123) or SI units (as A 123M). Inch-pound units and SI units are not necessarily exact equivalents. Within the text of this specification and where appropriate, SI units are shown in parentheses. Each system shall be used independently of the other without combining values in any way. In the case of orders in SI units, all testing and inspection shall be done using the metric equivalent of the test or inspection method as appropriate. In the case of orders in SI units, such shall be stated to the galvanizer when the order is placed.

Standard Specification for Zinc (Hot-Dip Galvanized) Coatings on Iron and Steel Products

BS EN 10253-3:2008 对焊管接头.无特殊检验要求的锻制奥氏体和奥氏体-铁素体(二相)不锈钢

1.1 This part of EN 10253 specifies the technical delivery requirements for seamless and welded buttwelding fittings (elbows, concentric and eccentric reducers, equal and reducing tees, caps) made of austenitic and austenitic–ferritic (duplex) stainless steel without specific inspection requirements. It specifies:  steel grades;  mechanical properties;  dimensions and tolerances;  requirements for inspection and testing;  inspection documents;  marking;  handling and packaging. 1.2 Limitation of use The allowed pressures and temperatures are the responsibility of the customer according to the state of the art and in application of the safety coefficients in the application regulations, codes and standards. In common, joint coefficient is used in the calculation of the thicknesses of components which include one or several butt welds, other than circumferential:  for equipment subject to random non-destructive testing: 0,85;  for equipment not subject to non-destructive testing other than visual inspection: 0,7. 1.3 Unless otherwise specified in this part of EN 10253 the general technical delivery requirements in EN 100021 apply.

Butt-welding pipe fittings - Part 3: Wrought austenitic and austenitic-ferritic (duplex) stainless steels without specific inspection requirements

KS D 3570-2008 高温排管用碳素钢管

이 표준은 주로 350 ℃를 초과하는 온도에서 배관에 사용하는 탄소 강관(이하 관이라 한다

Carbon steel pipes for high temperature service

KS D 3574-2008 机械结构用合金钢管

이 표준은 기계, 자동차, 그 밖의 기계 부품에 사용하는 합금강 강관(이하 관이라 한다.)

Alloy steel tubes for machine purposes

KS D 3569-2008 低温排管用钢管

이 표준은 빙점 이하의 특히 낮은 온도에서 배관에 사용되는 강관(이하 관이라 한다.)에 대

Carbon steel pipes for low temperature service

KS B ISO 1756:2008 工业车辆.托盘尺寸.连接装置

이 표준은 수동 받침대 트럭과 연결을 위해 받침대의 연결치수를 규정한다.비고 받

Industrial trucks－Dimensions of stillages－Connection gauge