H60 有色金属及其合金产品综合 标准查询与下载

ASTM A999/A999M-01 合金和不锈钢管用一般要求的标准规范

1.1 This specification covers a group of general requirements that, unless otherwise specified in an individual specification, shall apply to the ASTM product specifications noted below.1.2 In the case of conflict between a requirement of a product specification and a requirement of this specification, the product specification shall prevail. In the case of conflict between a requirement of the product specification or a requirement of this specification and a more stringent requirement of the purchase order, the purchase order shall prevail.Title of SpecificationASTM DesignationSeamless and Welded Austenitic Stainless Steel PipeA 312/A 312MSeamless and Welded Steel Pipe for Low-Temperature ServiceA 333/A 333MSeamless Ferritic Alloy-Steel Pipe for High Temperature ServiceA 335/A 335MElectric-Fusion-Welded Austenitic Chromium-Nickel Alloy Steel Pipe for High-Temperature ServiceA 358/A 358MCarbon and Ferritic Alloy Steel Forged and Bored Pipe for High-Temperature Service A 369/A 369MSeamless Austenitic Steel Pipe for Use With High Temperature Central-Station Service A 376/A 376MWelded Large Diameter Austenitic Steel Pipe for Corrosive or High-Temperature ServiceA 409/A 409MWelded, Unannealed Austenitic Stainless Steel Tubular ProductsA 778Seamless and Welded Ferritic/Austenitic Stainless Steel PipeA 790/A 790MSingle- or Double-Welded Austenitic Stainless Steel PipeA 813/A 813MCold-Worked Welded Austenitic Stainless Steel PipeA 814/A 814MFerritic/Austenitic (Duplex) Stainless Steel Pipe Electric Fusion Welded with Addition of Filler MetalA 928Spray-Formed Seamless Austenitic Stainless Steel PipeA 943Spray-Formed Seamless Ferritic/Austenitic Stainless Steel PipeA 949Austenitic Chromium-Nickel-Silicon Alloy Steel Seamless and Welded Pipe A 9541.3 The values stated in either inch-pound units or SI units are to be regarded separately as standard. With the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification. The inch-pound units shall apply unless the "M" designation (SI) of the product specification is specified in the order.Note 1--The dimensionless designator NPS (nominal pipe size) is used in this standard for such traditional terms as "nominal diameter," "size,"" nominal bore," and "nominal size". 1.4 The following precautionary statement pertains only to the test method portion, Section 21, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for General Requirements for Alloy and Stainless Steel Pipe

ASTM B899-01e1 有色金属及合金的相关标准术语

1.1 To promote precise understanding and interpretation of standard, reports, and other technical writings promulgated by Committee B02. 1.2 To standardize the terminology used in these documents. 1.3 To explain the meanings of technical terms used within these documents for those not conversant with them.

Standard Terminology Relating to Non-ferrous Metals and Alloys

ASTM B899-01 有色金属及合金的相关标准术语

1.1 To promote precise understanding and interpretation of standard, reports, and other technical writings promulgated by Committee B02. 1.2 To standardize the terminology used in these documents. 1.3 To explain the meanings of technical terms used within these documents for those not conversant with them.

Standard Terminology Relating to Non-ferrous Metals and Alloys

ASME 2316-2001 25Cr-7Ni-3Mo-W-Cu-N合金,UNS S39274 锻件、无缝焊接管道和管子件.第VIII节,第1部分

25Cr-7Ni-3Mo-W-Cu-N Alloy, UNS S39274 Forgings, Seamless and Welded Pipe and Tube Section VIII, Division 1

25Cr-7Ni-3Mo-W-Cu-N Alloy, UNS S39274 Forgings, Seamless and Welded Pipe and Tube Section VIII, Division 1

ASME 2304-1-2001 奥氏体Fe-35Ni-27Cr合金(UNS S35045).第VIII节,第1部分.(补充件10)R(2002)

Austenitic Fe-35Ni-27Cr Alloy (UNS S35045) Section VIII, Division 1; (SUPP 10) R(2002)

Austenitic Fe-35Ni-27Cr Alloy (UNS S35045) Section VIII, Division 1; (SUPP 10) R(2002)

ASME 2297-2001 9Cr-1Mo-V FCAW耗材用F-编号分组.第IX节(适用于所有章节,包括第III节,第I部分,和第XI节)

F-Number Grouping for 9Cr-1Mo-V FCAW Consumable Section IX (Applicable to all Sections, Including Section III, Division I, and Section XI

F-Number Grouping for 9Cr-1Mo-V FCAW Consumable Section IX (Applicable to all Sections, Including Section III, Division I, and Section XI

ASME 2281-2001 15Cr-5Ni-3Cu(UNS S15500) SA-705 型XM-12 情况 H1100.第VIII节,第3部分.已作废.补充件8&9

15Cr-5Ni-3Cu (UNS S15500) SA-705 Type XM-12 Condition H1100 Section VIII, Division 3 ANNULLED; SUPP 8&9

15Cr-5Ni-3Cu (UNS S15500) SA-705 Type XM-12 Condition H1100 Section VIII, Division 3 ANNULLED; SUPP 8&9

ASME 2277-2001 17Cr-4Ni-4Cu(UNS S17400)的使用.第VIII节,第2部分

Use of 17Cr-4Ni-4Cu (UNS S17400) Section VIII, Division 2

Use of 17Cr-4Ni-4Cu (UNS S17400) Section VIII, Division 2

ASME 2245-1-2001 25Cr-7.5Ni-3.5Mo-N-Cu-W合金,UNS S32760锻件,板材,薄材,带材,棒材,无缝焊接管道和管,以及配件.第VIII节,第1部分

25Cr-7.5Ni-3.5Mo-N-Cu-W Alloy, UNS S32760 Forgings, Plate, Sheet, Strip, Bar, Seamless and Welded Pipe and Tube, and Fittings Section VIII, Division 1

25Cr-7.5Ni-3.5Mo-N-Cu-W Alloy, UNS S32760 Forgings, Plate, Sheet, Strip, Bar, Seamless and Welded Pipe and Tube, and Fittings Section VIII, Division 1

ASME 2241-2001 制造与SE-747早期版本一致的IQIs线材的使用.第V节

Use of Wire IQIs Manufactured in Accordance with Earlier Editions of SE-747 Section V

Use of Wire IQIs Manufactured in Accordance with Earlier Editions of SE-747 Section V

ASME 2199-1-2001 2.25Cr-1.6W-V-Cb材料.第I节

2.25Cr-1.6W-V-Cb Material Section I

2.25Cr-1.6W-V-Cb Material Section I

ASME 2180-2-2001 无缝12Cr-2W材料.第I和VIII节,第1部分.补充件6 R(2002)

Seamless 12Cr-2W Material Sections I and VIII, Division 1; SUPP 6 R(2002)

Seamless 12Cr-2W Material Sections I and VIII, Division 1; SUPP 6 R(2002)

ASME 2179-3-2001 无缝9Cr-2W材料.第I节和第VIII节,第1部分

Seamless 9Cr-2W Material Section I and Section VIII, Division 1

Seamless 9Cr-2W Material Section I and Section VIII, Division 1

ASME 2151-1-2001 3 铬-1 钼-1/4 钒-钶-钙 合金钢板材和锻件.第VIII节,第1和2部分

3 Chromium-1 Molybdenum-1/4 Vanadium-Columbium-Calcium Alloy Steel Plates and Forgings Section VIII, Divisions 1 and 2

3 Chromium-1 Molybdenum-1/4 Vanadium-Columbium-Calcium Alloy Steel Plates and Forgings Section VIII, Divisions 1 and 2

ASME 2121-1-2001 Co-26Cr-9Ni-5Mo-3Fe-2W合金(UNS R31233).第VIII节,第1部分

Co-26Cr-9Ni-5Mo-3Fe-2W Alloy (UNS R31233) Section VIII, Division 1

Co-26Cr-9Ni-5Mo-3Fe-2W Alloy (UNS R31233) Section VIII, Division 1

ASME 2010-5-2001 规范施工用UNS R30556 Fe-22Cr-21Ni-18.5Co-La合金.第I节.(补充件11)

Fe-22Cr-21Ni-18.5Co-La Alloy, UNS R30556, for Code Construction Section I; (SUPP 11)

Fe-22Cr-21Ni-18.5Co-La Alloy, UNS R30556, for Code Construction Section I; (SUPP 11)

ASME SEC II-B INT VOL 47-2000 说明.第47卷.第II-B节

BPVC SECTION II B Interpretations Volume 47

Interpretations Volume 47 - Section II-B

ASME SEC II-B INT VOL 46-2000 说明.第46卷.第II-B节

BPVC SECTION II B Interpretations Volume 46

Interpretations Volume 46 - Section II-B

ASTM B635-00 镉锡机械沉积镀层标准规范

1.1 This specification covers the requirements for a coating that is a mixture of cadmium and tin mechanically deposited on metal products. The coating is provided in various thicknesses up to and including 12 956;m. 1.2 Mechanical deposition greatly reduces the risk of hydrogen embrittlement and is suitable for coating bores and recesses in many parts that cannot be conveniently plated electrolytically. (See Appendix X1.) 1.3 This standard does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazards statements, see Section 7.

Standard Specification for Coatings of Cadmium-Tin Mechanically Deposited

ASTM B774-00(2010) 低熔点合金的标准规范

1.1 This specification covers low-melting point metal alloys and solders, including bismuth–tin, bismuth–lead, bismuth–tin–lead, bismuth–tin–lead–cadmium, bismuth–tin–lead–indium–cadmium, bismuth–tin–lead–indium, indium–lead, and indium–lead–silver, and indium–tin joining together two or more metals at temperatures below their melting points; blocking for support and removable borders; radiation shielding; fusible plugs; fuses; tube bending; and punch setting. 1.1.1 This specification shall include those alloys having a liquidus temperature not exceeding 361°F (183°C), the melting point of the tin lead eutectic. 1.1.2 This specification includes low-melting point alloys in the form of solid bars, ingots, powder and special forms, and in the form of solid ribbon and wire. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.

Standard Specification for Low Melting Point Alloys