J05 结构要素 标准查询与下载

AIA/NAS NA 0155-1989 Rev. 1(Rev. 1)公制660兆帕剪力套环螺栓

"L" designates the length of the rod in inches and decinnrle of an inch.

Bolt, Clevis, 660 MPa Shear, Metric (Rev. 1) Rev 1

DIN 71803:1988 用螺桩、铆钉螺桩连接的角形连接件

Angle joints with screw studs, with rivet studs

AIA/NAS NAS 1684-1988 平折边型电子金属小孔

Eyelet, Metallic, Electrical, Flat Flanged Type

Eyelet, Metallic, Electrical, Flat Flanged Type

ANSI/ASME B1.8-1988 短梯形螺纹

When formulated prior to 1895, regular Acme screw threads were intended to replace square threads and a variety of threads of other forms used chiefly for the purpose of producing traversing motions on machines, tools, etc. For current information on Acme threads, see the latest edition of ASME/ANSI B1.5. The Stub Acme thread came into being early in the 1900s. Its use has been generally confined to those unusual applications where a coarse-pitch thread of shallow depth is required due to mechanical or metallurgical considerations. Federal Government Use. When this Standard is approved by the Department of Defense and Federal Agencies and is incorporated into FED-STD H28/13,Screw Thread Standards for Federal Services, Section 13, the use of this Standard by the Federal Government is subject to all the requirements and limitations of FED-STD H28/13.

Stub Acme Screw Threads

JIS B 1011:1987 中心孔

この規格は，機械加工，測定及び検査に用いるセソタ穴について規定する。

Centre holes

JIS B 0953:1987 T型槽的间距

Spacing of parallel T slots

JIS B 0952:1987 T型槽

T slots

AIA/NAS NA 0232-1987 公制型铁型阶梯式间隔套

Sheave web and hub dimensions optional providing pulley meets strength, weight, and oleirsnoe requirements of ipeoifiostion and drawing.

Spacer, Stepped, Swage Type, Metric

AIA/NAS NA 0231-1987 公制型铁型阶梯式间隔套

KINIHUM BORE TO BE SPECIFIED ON PART DRAWINO.

Spacer, Stepped, Swage Type, Metric

AIA/NAS NA 0231-0233-1987 公制型铁型阶梯式间隔套

Sheave web and hub dimensions optional providing pulley meets strength, weight, and oleirsnoe requirements of ipeoifiostion and drawing.

Spacer, Stepped, Swage Type, Metric

AIA/NAS NA 0233-1987 公制型铁型阶梯式间隔套

DIAMETERS TO BE CONCENTRIC WITHIN O05 TOTAL INDICATO READING.

Spacer, Stepped, Swage Type, Metric

AIA/NAS NAS 72-1987 (Rev. 5)镀铬钢向上夹套管

THIS STANDARD IS ESTABLISHED AS A MEANS TO EFFECT THE STANOARDIZATION OF THE IOENTIFICATION OF WIRE TERMINATIONS AS USED ON ELECTRICAL ANO ELECTRONIC COMPONENTS.

Bushing-Clamp-Up, Steel, Chrome Plated (Rev. 5)

DIN 649:1987 T形头螺钉用的T形槽

This standard specifies the dimensions of T-grooves for T-head bolts according to DIN 186, DIN 188, and DIN 261, as well as their designation.#,,#

T-slots for T-head bolts

ANSI/ASME B1.12-1987 螺纹.五级干涉配合.配合螺纹

Provides dimensional tables for external and internal plastic flow interference-fit (Class 5) threads of modified National thread form in the coarse thread series (NC) in sizes 0.250 in. through 1.500 in. This is not the ANSI B1.1 UN thread form. It is intended that designs conforming with this Standard will provide adequate torque conditions which fall within the limits shown in Table 8. The minimum torques are intended to be sufficient to insure that externally threaded members will not loosen in service; the maximum torques establish a ceiling below which seizing, galling, or torsional failure of the externally threaded components is reduced. This Standard provides for the maximum allowable interference.

Class 5 Interference - Fit Thread

UNI 149-1986 轮齿状花边．形状，尺寸和标记

Stabilisce le forme di zigrinature, le dimensioni e le regole per la rappresentazione convenzionale delle superfici zigrinate ottenute per deformazione plastica di compressione mediante rulli zigrinatori UNI 5599.

Knurls. Forms, dimensions and representations.

DIN 332-1:1986 60°中心孔.R、A、B 和C型

The standard specifies the dimensions of centre holes 60?without thread, used in the general engineering industry.#,,#

60° centre holes; types R, A, B, and C

AIA/NAS NA 0190-0193-1986 公制柳钉间隔套

THESE CONNECTIONS SHALL BE CAPABLE OF WITHSTANDING YO0 PSI INTERNAL AIR PRESSURE.

Spacer, Sleeve-Rivet, Metric

AIA/NAS NA 0190-1986 公制柳钉间隔套

This standard provides a method for the packaging of optical components or assemblies having critical surfaces (e.g., mirrors, lenses, optical filters,etc.).

Spacer, Sleeve-Rivet, Metric

AIA/NAS NA 0180-1986 公制螺栓及螺杆间隔套

This standard provides a method f o r the packaging of an item in a box-bag-box, with desiccant,

Spacer, Sleeve-Screw and Bolt, Metric

AIA/NAS NA 0193-1986 公制柳钉间隔套

GENERAL ELECTRIC WANY, LAMP DEFT. SIMILAR ITEM3 OF COFIPARAEbE FUNCTION MUST BE EQUIVALENT PFUOR TO USE ON AIRGRBPT IN LIER OF ITEMS SHOWN BERMN.

Spacer, Sleeve-Rivet, Metric