J18 链传动、皮带传动与键联结 标准查询与下载
共找到 837 条与 链传动、皮带传动与键联结 相关的标准，共 56 页
This International Standard specifies a dynamic test method for the quality control of V-ribbed belts (PK profile) which are used predominantly for accessory drive applications in the automotive industry. The dimensional characteristics of the belts and of corresponding pulleys are the subject of ISO 9981.
Belt drive - V-ribbed belts for the automotive industry - Fatigue test
- ICS
- 21.220.10;43.060.10
- CCS
- J18
- 发布
- 2014-02
- 实施
This Standard specifies the characteristics and the following matters of ball splines. —Shapes and dimensions —Test methods —Inspections —Designations of products —Marking
Ball splines -- Part 1: General characteristics and requirements
- ICS
- 21.100;21.120.30
- CCS
- J18
- 发布
- 2013-10-21
- 实施
This Standard specifies the calculation method of the basic dynamic load rating, basic static load rating and basic rating life for the design and use of ball splines of Type AI, Type AII and Type R. It also establishes the basic dynamic torque rating and the basic static torque rating for these ball splines.
Ball splines -- Part 2: Dynamic and static load ratings and rating life
- ICS
- 25.060.99
- CCS
- J18
- 发布
- 2013-10-21
- 实施
本标准规定了输送用钢制开式套筒销合链的术语和定义、结构型式、基本参数和尺寸、抗拉强度和链长精度,以及与这些链条相配的附件和链轮的技术要求。本标准适用于农业机械和环保机械等不洁净的场合使用的开式销合链、附件和链轮。
Open barrel steel pintle-type conveyor chains, attachments and sprockets
- ICS
- 21.220.30
- CCS
- J18
- 发布
- 2013-04-25
- 实施
- 2013-09-01
本标准规定了摩托车用外啮合和内-外复合啮合齿形链条的基本参数、技术要求和检验方法。本标准适用于摩托车发动机正时及机油泵等机构使用的齿形链条。
Inverted tooth chains for motorcycles
- ICS
- 21.220.30
- CCS
- J18
- 发布
- 2013-04-25
- 实施
- 2013-09-01
本标准规定了滚子链和套筒链(以下简称链条)的术语和定义、结构型式、基本参数和尺寸、链长精度、预拉、最小抗拉强度和动载试验载荷,以及测量用链轮尺寸及极限偏差。本标准适用于汽车发动机的凸轮轴以及驱动机构的精密滚子链和套筒链。
Roller chains and bush chains for automobiles
- ICS
- 21.220.30
- CCS
- J18
- 发布
- 2013-04-25
- 实施
- 2013-09-01
本标准规定了摩托车传动链条磨损性能试验的技术要求、试验条件、试验方法和试验设备。本标准适用于摩托车(含其他行走机械)上的驱动用传动链条。
Motorcycle transmission chains.Testing rules of wear performance
- ICS
- 21.220.30
- CCS
- J18
- 发布
- 2013-04-25
- 实施
- 2013-09-01
本标准规定了农业机械用夹持输送链的结构型式、主要尺寸、技术要求和产品的标记等。本标准适用于行走式小麦、水稻收割机和定置式机动稻麦脱粒机,以及半喂入式联合收割机上使用的茎杆夹持输送链条。
Feed chains for agricultural machinery
- ICS
- 21.220.30
- CCS
- J18
- 发布
- 2013-04-25
- 实施
- 2013-09-01
Synchronous belt drives - Pulleys
- ICS
- 21.220.10
- CCS
- J18
- 发布
- 2013-02-23
- 实施
- 2013-02-23
This Standard defines terms relating to generalise seamless V-belts, V-ribbed belts, V-grooved pulleys and V-ribbed pulleys that are intended for power transmission.
Belt drives -- V-belts and V-ribbed belts, and corresponding grooved pulleys -- Vocabulary
- ICS
- 01.040.21;21.220.10
- CCS
- J18
- 发布
- 2013-02-20
- 实施
Synchronous belt drives. Pulleys
- ICS
- 21.220.10
- CCS
- J18
- 发布
- 2013-01-31
- 实施
- 2013-01-31
700 Class Chains, Attachments and Sprocket Teeth for Water and Sewage Treatment Plants
- ICS
- 21.220.30
- CCS
- J18
- 发布
- 2013-01-01
- 实施
Fatigue Testing Power Transmission Roller Chain
- ICS
- 21.220.30
- CCS
- J18
- 发布
- 2013-01-01
- 实施
This Standard covers fatigue testing, in axial tension, of power transmission roller chains in ASME B29.1M and ASME B29.3M, and nonstandard variants of those chains. The purpose of this Standard is to provide a uniform, reliable method of determining the fatigue strength of power transmission roller chains so that equivalent and comparable results can be obtained from axial fatigue testing at different laboratories.
Fatigue Testing Power Transmission Roller Chain
- ICS
- 21.220.30
- CCS
- J18
- 发布
- 2013
- 实施
- 2013-11-20
This International Standard specifies the principal characteristics of synchronous pulleys for use in synchronous endless belt drives for mechanical power transmission and where positive indexing or synchronization is required. NOTE These drives have been known under various names in the past, for example: timing belt drives, positive belt drives, gear belt drives. The principal characteristics include: a) tooth dimensions and tolerances; c) quality specification. b) pulley dimensions and tolerances; As far as dimensions are concerned, the pulleys specified in this International Standard are used interchangeably with the belts specified in ISO 5296.
Synchronous belt drives - Pulleys
- ICS
- 21.220.10
- CCS
- J18
- 发布
- 2012-12
- 实施
Conveyor belts with heat-resistant rubber covers. Heat resistance of covers. Requirements and test methods
- ICS
- 53.040.20
- CCS
- J18
- 发布
- 2012-11-30
- 实施
- 2012-11-30
Belt drives. Grooved pulleys for V-belts (system based on effective width). Geometrical inspection of grooves
- ICS
- 21.220.10
- CCS
- J18
- 发布
- 2012-11-30
- 实施
- 2012-11-30
Conveyor belts. Test atmospheres and conditioning period
- ICS
- 53.040.20
- CCS
- J18
- 发布
- 2012-11-30
- 实施
- 2012-11-30
Belt drives - Grooved pulleys for V-belts (system based on effective width) - Geometrical inspection of grooves
- ICS
- 21.220.10
- CCS
- J18
- 发布
- 2012-11
- 实施
本标准规定了出口工业链条的抽样、检验方法，以及检验结果的判定规则。 本标准适用于精密滚子链和套筒链的出口检验，其他工业链条的出口检验亦可参照使用。
Rules for the inspection of industrial chains for export.General requirement
- ICS
- CCS
- J18
- 发布
- 2012-10-23
- 实施
- 2013-05-01
