J32 锻压 标准查询与下载
共找到 789 条与 锻压 相关的标准，共 53 页
本标准规定了50 MW以下汽轮发电机无中心孔转子锻件的订货要求、制造工艺、技术要求、检验规则和试验方法、验收和质量证明书及标志和包装等。本标准适用于50 MW以下汽轮发电机无中心孔转子锻件的订货、制造与检验。
The non-central hole rotor forgings for below 50 MW turbine generator.Technical specification
- ICS
- 77.140.85
- CCS
- J32
- 发布
- 2014-07-09
- 实施
- 2014-11-01
本标准规定了工业汽轮机转子体用经真空处理的合金钢锻件的订货要求、制造工艺、技术要求、检验规则和试验方法、验收与质量证明书及标志和包装。本标准适用于工业汽轮机转子体锻件的订货、制造和验收。
The rotor forgings for industrial steam turbines.Technical specification
- ICS
- 77.140.85
- CCS
- J32
- 发布
- 2014-05-06
- 实施
- 2014-10-01
本标准规定了300 MW以上汽轮机有中心孔转子体用经真空处理的合金钢锻件的订货要求、制造工艺、技术要求、检验规则和试验方法、验收和质量证明书及标志和包装。本标准适用于300 MW以上汽轮机在高温和(或)高应力下工作的有中心孔转子体锻件的订货、制造与检验。
Rotor forgings for 300 MW steam turbines and above.Technical specification
- ICS
- 77.140.85
- CCS
- J32
- 发布
- 2014-05-06
- 实施
- 2014-10-01
本标准规定了300 MW以上汽轮机无中心孔转子体用经真空处理的合金钢锻件的订货要求、制造工艺、技术要求、检验规则和试验方法、验收和质量证明书及标志和包装。本标准适用于300 MW以上汽轮机在高温和(或)高应力下工作的无中心孔转子体锻件的订货、制造与检验。
The non-central hole rotor forgings for 300 MW steam turbines and above.Technical specification
- ICS
- 77.140.85
- CCS
- J32
- 发布
- 2014-05-06
- 实施
- 2014-10-01
本标准规定了连轧管机组用限动芯棒(以下简称芯棒)的订货要求、制造工艺、技术要求、检验规则和试验方法、验收和质量证明书及标志和包装。本标准适用于直径小于或等于500 mm的连轧管机组用限动芯棒的订货、制造和检验。
The retained mandrel for multi-stand pipe mill
- ICS
- 77.140.85
- CCS
- J32
- 发布
- 2014-05-06
- 实施
- 2014-10-01
本标准规定了25 MW~200 MW汽轮机转子体和主轴锻件用经真空处理的合金钢锻件的订货要求、制造工艺、技术要求、检验规则和试验方法、验收和质量证明书及标志和包装。本标准适用于蒸汽温度不超过565℃汽轮机转子体和主轴用经真空处理的合金钢锻件的订货、制造与检验。
Rotor and shaft forgings for 25 MW to 200 MW steam turbines.Technical specification
- ICS
- 77.140.85
- CCS
- J32
- 发布
- 2014-05-06
- 实施
- 2014-10-01
本标准规定了50 MW~200 MW汽轮发电机转子用真空处理合金钢锻件的订货要求、制造工艺、技术要求、检验规则和试验方法、验收和质量证明书及标志和包装。本标准适用于50 MW~200 MW汽轮发电机转子用真空处理的合金钢锻件的订货、制造和检验。
Rotor forgings for 50 MW to 200 MW turbine generators.Technical specification
- ICS
- 77.140.85
- CCS
- J32
- 发布
- 2014-05-06
- 实施
- 2014-10-01
本标准规定了汽轮发电机用磁性环碳钢及合金钢锻件的订货要求、制造工艺、技术要求、检验规则和试验方法、验收和质量证明书及标志和包装。本标准适用于电站汽轮发电机的中心环、风扇环、小护环、水箱压环等锻件的订货、制造和检验。本标准不适用于无磁性环锻件。
The magnetic ring forgings for turbine generators.Technical specification
- ICS
- 77.140.85
- CCS
- J32
- 发布
- 2014-05-06
- 实施
- 2014-10-01
La présente Norme internationale spécifie les dimensions principales et les tolérances des plaques d'entraînements de came et de coulissement utilisées dans les outillages de presse.Elle spécifie également la désignation des plaques d'entraînement de came.
Tools for pressing - Cam driver plates
- ICS
- 25.120.10
- CCS
- J32
- 发布
- 2014-03-26
- 实施
- 2014-03-26
Tools for pressing - Sliding plates (ISO 23480:2013)
- ICS
- 25.120.10
- CCS
- J32
- 发布
- 2014-03
- 实施
This part of ISO 11901 specifies the dimensions (in millimetres), nominal initial forces and types of gas springs. It also specifies marking, technical delivery conditions and designation. NOTE Specifications of mounting accessories for gas springs are given in ISO 11901-2.
Tools for pressing - Gas springs - Part 3: Gas spring with increased spring force and compact built height
- ICS
- 21.160;25.120.10
- CCS
- J32
- 发布
- 2014-03
- 实施
This part of ISO 11901 specifies the dimensions (in millimetres), nominal initial forces and types of gas springs. It also specifies marking, technical delivery conditions and designation. NOTE Specifications of mounting accessories for gas springs are given in ISO 11901-2.
Tools for pressing - Gas springs - Part 4: Gas springs with increased spring force and same built height
- ICS
- 21.160;25.120.10
- CCS
- J32
- 发布
- 2014-03
- 实施
Tools for pressing. Gas springs. Gas springs with increased spring force and same built height
- ICS
- 21.160;25.120.10
- CCS
- J32
- 发布
- 2014-02-28
- 实施
- 2014-02-28
1.1 This specification2 covers forged carbon steel piping components for ambient- and higher-temperature service in pressure systems. Included are flanges, fittings, valves, and similar parts ordered either to dimensions specified by the purchaser or to dimensional standards such as the MSS, ASME, and API specifications referenced in Section 2. Forgings made to this specification are limited to a maximum weight of 10 000 lb [4540 kg]. Larger forgings may be ordered to Specification A266/A266M. Tubesheets and hollow cylindrical forgings for pressure vessel shells are not included within the scope of this specification. Although this specification covers some piping components machined from rolled bar and seamless tubular products (see 5.2), it does not cover raw material produced in these product forms. 1.2 Supplementary requirements are provided for use when additional testing or inspection is desired. These shall apply only when specified individually by the purchaser in the order. 1.3 Specification A266/A266M covers other steel forgings and Specifications A675/A675M and A696 cover other steel bars. 1.4 This specification is expressed in both inch-pound units and SI units. However, unless the order specifies the applicable “M” specification designation (SI units), the material shall be furnished to inch-pound units. The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. Note 1: The dimensionless designator NPS (nominal pipe size) has been substituted in this standard for such traditional terms as “nominal diameter,” “size,” and “nominal size.”
Standard Specification for Carbon Steel Forgings for Piping Applications
- ICS
- 77.140.85
- CCS
- J32
- 发布
- 2014
- 实施
JB/T 9179的本部分规定了液压机上钢质自由锻件机械加工余量与公差的一般要求。本部分适用于在液压机上用自由锻方式锻造的钢质自由锻件。本部分规定的机械加工余量与公差适用于单件或小批量规模生产的钢质自由锻件。
Machining allowances and tolerances of open die forgings on hydraulic press.Part 1: General requirements
- ICS
- 77.140.85
- CCS
- J32
- 发布
- 2013-12-31
- 实施
- 2014-07-01
JB/T 9179的本部分规定了液压机上自由锻台阶轴类钢质自由锻件的余量与公差。本部分适用于截面为圆形、方形和矩形的各类台阶轴类钢质自由锻件。
Machining allowances and tolerances of open die forgings on hydraulic press.Part 3: Stepped shaft
- ICS
- 77.140.85
- CCS
- J32
- 发布
- 2013-12-31
- 实施
- 2014-07-01
JB/T 9179的本部分规定了在液压机上自由锻圆轴、方轴和矩形截面类钢质自由锻件的机械加工余量与公差。本部分适用于长度大于等于直径、方截面边长和矩形截面长边的圆轴、方轴和矩形截面类钢质自由锻件。对于对称多边形轴类钢质自由锻件的机械加工余量与公差可按本部分规定参照执行。
Machining allowances and tolerances of open die forgings on hydraulic press.Part 2: Round shaft, square shaft and rectangular cross-section
- ICS
- 77.140.85
- CCS
- J32
- 发布
- 2013-12-31
- 实施
- 2014-07-01
JB/T 9179的本部分规定了在液压机上自由锻筒体类(含有台阶筒体)钢质自由锻件的余量与公差。本部分适用于最终经芯棒拔长工序完工的筒体类(含台阶筒体)钢质自由锻件。
Machining allowances and tolerances of open die forgings on hydraulic press.Part 7: Cylinder
- ICS
- 77.140.85
- CCS
- J32
- 发布
- 2013-12-31
- 实施
- 2014-07-01
JB/T 9179的本部分规定了在液压机上自由锻圆环、筒节、法兰类钢质自由锻件的余量与公差。本部分适用于最终经芯棒(马杠)扩孔工序完工的圆环、筒节、法兰类钢质自由锻件。
Machining allowances and tolerances of open die forgings on hydraulic press.Part 8: Ring, cylinder segment and flange
- ICS
- 77.140.85
- CCS
- J32
- 发布
- 2013-12-31
- 实施
- 2014-07-01
