焊接与切割设备标准-分析测试百科网

DIN EN ISO 5172:2012 气体焊接设备.气焊,预热和切割用喷焊器.检验和规范(ISO 5172-2006 + Amd 1-2012).德文版本EN ISO 5172-2006 + A1-2012

Gas welding equipment - Blowpipes for gas welding, heating and cutting - Specifications and tests (ISO 5172:2006 + Amd 1:2012); German version EN ISO 5172:2006 + A1:2012

ICS: 25.160.30
CCS: J64
发布: 2012-11
实施

BS EN 60974-1:2012 电弧焊设备.焊接电源

Arc welding equipment. Welding power sources

ICS: 25.160.30
CCS: J64
发布: 2012-08-31
实施: 2012-08-31

EN ISO/TS 15011-6:2012 焊接和相关工艺的卫生和安全.烟雾和气体取样的方法.第6部分:电阻点焊的烟尘和气体定量测定程序

Health and safety in welding and allied processes - Laboratory method for sampling fume and gases - Part 6: Procedure for quantitative determination of fume and gases from resistance spot welding

ICS: 25.160.10
CCS: J64
发布: 2012-07-01
实施

ISO 5172:2006/Amd 1:2012 气体焊接设备.气焊,预热和切割用喷焊器.检验和规范.修改件1

Gas welding equipment - Blowpipes for gas welding, heating and cutting - Specifications and tests; Amendment 1

ICS: 25.160.30
CCS: J64
发布: 2012-07
实施

IEC 60974-1:2012 弧焊设备. 第1部分: 焊接电源

This part of IEC 60974 is applicable to power sources for arc welding and allied processes designed for industrial and professional use@ and supplied by a voltage not exceeding 1 000 V@ or driven by mechanical means. This part of IEC 60974 specifies safety and performance requirements of welding power sources and plasma cutting systems. This part of IEC 60974 is not applicable to welding power sources for manual metal arc welding with limited duty operation which are designed mainly for use by laymen and designed in accordance with IEC 60974-6. This part of IEC 60974 is not applicable to testing of power sources during periodic maintenance or after repair. NOTE 1 Typical allied processes are electric arc cutting and arc spraying. NOTE 2 AC systems having a nominal voltage between 100 V and 1 000 V are given in Table 1 of IEC 60038:2009. NOTE 3 This part of IEC 60974 does not include electromagnetic compatibility (EMC) requirements.

Arc welding equipment - Part 1: Welding power sources

ICS: 25.160.30
CCS: J64
发布: 2012-06
实施: 2017-02-10

JB/T 7783-2012 管子坡口机技术条件

本标准规定了管子坡口机的分类、基本参数、技术要求、检验方法和检验规则。本标准适用于管子坡口机（以下简称坡口机）。

The specification for pipe beveling machines

ICS: 25.160.30
CCS: J64
发布: 2012-05-24
实施: 2012-11-01

DIN EN 60974-12:2012 弧焊设备.第12部分:焊接电缆连接设备

Arc welding equipment - Part 12: Coupling devices for welding cables (IEC 60974-12:2011); German version EN 60974-12:2011

ICS: 25.160.30
CCS: J64
发布: 2012-03-01
实施: 2012-03-01

DIN EN 60974-13:2012 电弧焊设备.第13部分:电焊钳(IEC 60974-13-2011).德文版本EN 60974-13-2011

Arc welding equipment - Part 13: Welding clamp (IEC 60974-13:2011); German version EN 60974-13:2011

ICS: 25.160.30
CCS: J64
发布: 2012-03
实施: 2012-03-01

BS EN ISO 11148-2:2011 手持非电动工具.安全性要求.切割和卷边动力工具

Hand-held non-electric power tools. Safety requirements. Cutting-off and crimping power tools

ICS: 25.140.10
CCS: J64
发布: 2012-01-31
实施: 2012-01-31

ANSI/AWS C4.5M:2012 氧化燃料喷嘴的统一命名体系

This document presents recommendations to Oxyfuel welding, cutting, and heating/brazing torch nozzle manufacturers regarding the identification markings to be permanently applied to the torch nozzle to identify its intended application. The identification will provide information to improve the safe operation and application of nozzles by torch operators. This standard makes use of the International System of Units (SI).

Uniform Designation System for Oxyfuel Nozzles (3rd Edition)

ICS: 25.160.30
CCS: J64
发布: 2012
实施

ANSI/NFPA 51-2012 焊接、切削和同系列加工的氧燃料气体系统的设计和安装标准

1.1 Scope. 1.1.1 This standard applies to the following: (1) Design and installation of oxygenûfuel gas welding and cutting systems and allied processes (see 3.3.2), except for systems meeting the criteria in 1.1.5 (2) Utilization of gaseous fuels generated from flammable liquids under pressure where such fuels are used with oxygen(3) Storage on the site of a welding and cutting system installation of the following: (a) Gases to be used with such systems where more than one cylinder each of oxygen and fuel gas are stored in any single storage area [includes storage of more than one cylinder each in any single storage area even though all such stored cylinders may be intended for use in systems of the kind described in 1.1.5(1)] (b) Calcium carbide 1.1.2 Unless specifically indicated otherwise, the term welding and cutting systems shall be considered to include allied processes in this standard. 1.1.3 Where only a portion of a fuel gas system is to be used for welding, cutting, or allied processes, only that portion of the system need comply with this standard. 1.1.4 Where only a portion of an oxygen system is to be used with fuel gas for welding, cutting, or allied processes, only that portion of the system need comply with this standard. 1.1.5 This standard shall not apply to the following: (1)*Systems consisting of a single cylinder not exceeding 3.4 m3(120 ft3) of oxygen and a single cylinder not exceeding 3.4 m3 (120 ft3) of fuel gas used for welding and cutting (2) Systems in which fuel gases are not to be used with oxygen, as described in NFPA 54, National Fuel Gas Code, and NFPA 58, Liquefied Petroleum Gas Code (3) The manufacture of gases and the filling of cylinders (4) Storage of empty cylinders (5) Compressed airûfuel gas systems

Standard for the Design and Installation of Oxygen-Fuel Gas Systems for Welding, Cutting, and Allied Processes