J64 焊接与切割设备 标准查询与下载

BS EN 60974-2:2008 弧焊设备.液体冷却系统

This part of IEC 60974 specifies safety and construction requirements for industrial and professional liquid cooling systems used in arc welding and allied processes to cool torches. This part of IEC 60974 is applicable to stand-alone liquid cooling systems that are either connected to a separate welding power source or built into the welding power source enclosure. This part of IEC 60974 is not applicable to refrigerated cooling systems.

Arc welding equipment — Part 2: Liquid cooling systems

JIS C 9321 AMD 1:2009 电容器放电式点焊接机(修改件1)

This translation has been made based on the Amendment to the origi- nal Japanese Industrial Standard revised by the Minister of Economy, Trade and Industry through deliberations at the Japanese Industrial Standards Committee as the result of proposal for revision of Japanese Industrial Standard with the draft being attached, based on the provi- sion of Article 12 Clause 1 of the Industrial Standardization Law ap- plicable to the case of revision by the provision of Article 14. Consequently, JIS C 9321:1991 is partially replaced with this Amend- ment.

Capacitor discharge type spot welding machines (Amendment 1)

NF A89-701-4:2009 高质量焊接和切削用CO2激光束机器的验收试验.第4部分:2-D移动光学机

Acceptance tests for CO2-laser beam machines for high quality welding and cutting - Part 4 : machines with 2-D moving optics.

BS EN 50504:2008 弧焊设备的有效性

This European Standard specifies validation methods for arc welding equipment constructed and used to the accuracy specified in EN 60974-1 or other equivalent standards. The accuracy of this equipment is designated as standard grade. This European Standard is applicable to a) arc welding power sources, b) wire feeders, c) welding instrumentation. This European Standard is not applicable to arc striking and stabilizing device. Calibration, verification and validation of equipment for other welding processes and ancillary equipment which may affect the quality of the weld, e.g. flow gauges, thermocouples, robots and manipulators are given in EN ISO 17662.

Validation of arc welding equipment

NF A85-611-1:2009 电阻焊接设备.第1部分:设计、制造和安装的安全要求

Resistance welding equipment - Part 1 : safety requirements for the design, manufacture and the installation.

DIN EN ISO 14113:2009 气焊设备.450巴(45MPa)以下工业气体传输用橡胶和塑料软管及其组件

This International Standard specifies requirements for rubber and plastics hose and hose assemblies for use with compressed, liquefied and dissolved gases up to a maximum working pressure of 45 MPa (450 bar), within the ambient temperature range of -20 ~C to +60 ~C. This International Standard applies to hose assemblies used to connect industrial gas cylinders to manifolds or bundles prior to any pressure reduction stage. This International Standard does not cover rubber or thermoplastic hoses for welding, cutting and allied processes (see ISO 3821 and ISO 12170). This International Standard does not apply to refrigerated liquefied gases or to liquefied petroleum gases (LPG).

Gas welding equipment - Rubber and plastics hose and hose assemblies for use with industrial gases up to 450 bar (45 MPa) (ISO 14113:2007); German version EN ISO 14113:2008

ANSI/IEC 60974-12:2009 弧焊设备.第12部分:联结装置

Safety and performance requirements for coupling devices applicable for welding, cutting and allied processes, and designed for industrial and professional use

Arc Weilding Equipment - Part 12 : coupling devices

ANSI/IEC 60974-7:2009 弧焊设备.第7部分:焊炬

Safety and performance requirements for torches applicable for welding, cutting and allied processes, and designed for industrial and professional use

Arc Weilding Equipment - Part 7 : torches

ANSI/AWS C4.2/C4.2M:2009 安全氧气切割炬操作的推荐实施规范

These recommended practices for oxyfuel gas cutting include the latest procedures to be used in conjunction with oxyfuel gas cutting equipment and the latest safety recommendations. Complete lists of equipment are available from individual manufacturers.

Recommended Practices for Safe Oxyfuel Gas Cutting Torch Operation

ANSI/IEC 60974-8:2009 弧焊设备.第8部分:气体控制台

Safety and performance requirements for gas consoles intended to be used with combustible gases or oxygen. These gas consoles are designed to supply gases for use in arc welding, plasma cutting, gouging and allied processes in non-explosive atmospheres. The gas console can be external or internal to the power source enclosure. In the latter case, this standard also applies to the power source.

Arc Welding Equipment - Part 8: Gas Consoles

ANSI/UL 551-2009 变压器型弧焊机安全性标准

Proposing a change in the scope of the standard to limit coverage to hobby welders only.

Standard for Safety for Transformer-Type Arc-Welding Machines

ANSI/IEC 60974-11:2009 弧焊设备.第11部分:焊条夹

Safety and performance requirements for electrode holders applicable for welding, cutting and allied processes, and designed for industrial and professional use

Arc Weilding Equipment - Part 11 : electrode holders

KS B ISO 15794:2008 双向和多向升降叉车.稳定性试验

이 표준은 틸트식 또는 고정식 마스트나 포크가 장착된 사이드 지게차의 안정성을 검증하기 위

Bi-directional and multi-directional fork-lift trucks-Stability tests

JIS C 9300-1 AMD 1:2008 弧焊设备.第1部分:弧焊电源(修改件1)

Arc welding equipment -- Part 1: Arc welding power sources(Amendment 1)

KS B ISO 18595:2008 电阻焊接.铝和铝合金的点焊.可焊接性、焊接和测试

이 표준은 알루미늄 판재, 압출재(가공, 시효경화 합금) 그리고 판두께가 0.6∼6 mm

Resistance welding－Spot welding of aluminium and aluminium alloys－Weldability, welding and testing

KS C 9323-2008 电动马桶

이 표준은 항문 또는 국부를 물로 닦아주는 수도 직결식 급수방식(사용 최고수압 735 kP

Electric bidet

KS C 9322-2008 炕式电动床

이 표준은 석재, 황토, 숯 등 무기재료를 온돌판의 주원료로 사용하고 보료 내부에 전열장치

Electric beds of Ondol type

ISO 15616-4:2008 高质量焊接和切割用CO2激光光束机的验收试验.第4部分:带二维移动光学的机械

This part of ISO 15616 provides minimum requirements for acceptance testing, using practical test methods, for CO-laser beam machines for high quality welding and cutting in two dimensions (2-D), having a fixed workpiece on the platen and moving optics. This part of ISO 15616 is not applicable to CO-laser beam machines which use an articulated robot, nor does it apply to work stations, such as a welding positioner, fixed board cutter, etc. This part of ISO 15616 does not cover hazard protection devices, such as those for discharging chips and particles generated during welding and cutting.

Acceptance tests for CO-laser beam machines for high quality welding and cutting — Part 4: Machines with 2-D moving optics

KS C 9324-2008 电动洗菜机

이 표준은 과일 또는 야채, 곡물 등에 묻은 오염 물질을 깨끗하게 세척하기 위하여 진동자와

Vegetable washing machines

JIS C 9300-7 ERRATUM 1:2008 勘误表

ERRATUM