J64 焊接与切割设备 标准查询与下载

IEC 60974-2:2007 电弧焊接设备.第2部分:液体冷却系统

This part of IEC 60974 specifies safety and construction requirements for industrial and professional liquid cooling systems used in arc welding and allied processes to cool torches. This part of IEC 60974 is applicable to stand-alone liquid cooling systems that are either connected to a separate welding power source or built into the welding power source enclosure. This part of IEC 60974 is not applicable to refrigerated cooling systems. NOTE 1 Typical allied processes are, for example, plasma arc cutting and arc spraying. NOTE 2 This part of IEC 60974 does not include electromagnetic compatibility (EMC) requirements.

Arc welding equipment - Part 2: Liquid cooling systems

IEC 60974-5:2007 电弧焊设备.第5部分:焊丝进料装置

This part of IEC 60974 specifies safety and performance requirements for industrial and professional equipment used in arc welding and allied processes to feed filler wire. The wire feeder may be a stand-alone unit which may be connected to a separate welding power source or one where the welding power source and the wire feeder are housed in a single enclosure. The wire feeder may be suitable for manually or mechanically guided torches. This part of IEC 60974 is not applicable to spool-on torches that are covered by IEC 60974-7. This part of IEC 60974 is not applicable to wire feeders which are designed for use by laymen and are covered by IEC 60974-6. NOTE 1 Typical allied processes are, for example, plasma arc cutting and arc spraying. NOTE 2 This standard does not include electromagnetic compatibility (EMC) requirements.

Arc welding equipment - Part 5: Wire feeders

ISO 14113:2007 气焊设备.450巴(45MPa)以下工业气体传输用橡胶和塑料软管及其组件

This International Standard specifies requirements for rubber and plastics hose and hose assemblies for use with compressed, liquefied and dissolved gases up to a maximum working pressure of 45 MPa (450 bar), within the ambient temperature range of ?20 °C to +60 °C. This International Standard applies to hose assemblies used to connect industrial gas cylinders to manifolds or bundles prior to any pressure reduction stage. This International Standard does not cover rubber or thermoplastic hoses for welding, cutting and allied processes (see ISO 3821 and ISO 12170). This International Standard does not apply to refrigerated liquefied gases or to liquefied petroleum gases (LPG).

Gas welding equipment - Rubber and plastics hose and hose assemblies for use with industrial gases up to 450 bar (45 MPa)

JIS C 9300-7:2007 弧焊设备.第7部分:焊炬(枪)

この規格は，アーク溶接及び関連プロセスのために用いるトーチの，性能要件及び安全要件について規定する。この規格において，トーチはトーチボディ，ケーブルホースアセンブリ及びその他の部品で構成する。

Arc welding equipment -- Part 7: Torches

JIS C 9300-3:2007 弧焊设备.第3部分:电弧放电和稳定设备

この規格は，アーク溶接並びに類似のプロセスに用いられるアーク起動及びアーク安定化装置(以下，この装置という。)の安全にかかわる構造及び性能について規定する。

Arc welding equipment -- Part 3: Arc striking and stabilizing devices

DIN EN 60974-4:2007 电弧焊设备.第4部分:使用中的检验和测试(IEC 60974-4:2006)

Arc welding equipment - Part 4: In-service inspection and testing (IEC 60974-4:2006); German version EN 60974-4:2007

SANS 1671-1:2007 热塑性塑料的焊接．机械和设备．第1部分：热工具焊接

Specifies requirements for machines and equipment used for heated-tool butt welding and socket welding of thermoplastics, in particular for the welding of polyethylene (PE), polypropylene (PP), polybutylene (PB) and polyvinylidene fluoride (PVDF). Is int

Welding of thermoplastics - Machines and equipment Part 1: Heated-tool welding

KS C 9602-2007 交流弧焊机

이 규격은 주파수 60 Hz의 단상 변압기를 주체로 하는 교류 아크 용접기(이하 용접기라

AC arc welding machines

KS B ISO 15607:2007 金属材料焊接程序规范和合格鉴定.总则

이 규격은 금속 재료 용접절차시방서 및 승인에 관한 일반 규칙을 정의한다. 이 규격은 또한

Specification and qualification of welding procedures for metallic materials－General rules

IEC 62135-2:2007 电阻焊接设备.第2部分:电磁兼容性(EMC)要求

This part of IEC 62135 is applicable to equipment for resistance welding and allied processes which are connected to mains supplies with rated voltages up to 1 000 V a.c. r.m.s. This standard does not define safety requirements. Resistance welding equipment type tested in accordance with, and which has met the requirements of, this standard, shall be deemed to be in compliance for all applications. The frequency range covered is from 0 Hz to 400 GHz. This product EMC standard for resistance welding equipment takes precedence over all aspects of the generic standards and no additional EMC tests are required or necessary. NOTE 1 Typical allied processes are resistance hard and soft soldering or resistance heating achieved by means comparable to resistance welding equipment. NOTE 2 Limit values are specified for only part of the frequency range. Resistance welding equipment are classified as Class A and Class B equipment. This part of IEC 62135 specifies a) test methods to be used in conjunction with CISPR 11 to determine radiofrequency (r.f.) emission; b) relevant standards and test methods for harmonic current emission, voltage fluctuation and flicker. NOTE 3 The limits in this standard may not, however, provide full protection against interference to radio and television reception when the resistance welding equipment is used closer than 30 m to the receiving antenna(e). NOTE 4 In special cases, when highly susceptible apparatus is being used in close proximity, additional mitigation measures may have to be employed to further reduce the electromagnetic emissions. This part of IEC 62135 also defines immunity requirements and test methods for continuous and transient, conducted and radiated disturbances including electrostatic discharges. NOTE 5 These requirements do not, however, cover extreme cases which are extremely rare.

Resistance welding equipment - Part 2: Electromagnetic compatibility (EMC) requirements

IEC 60974-10:2007 弧焊设备.第10部分:电磁兼容性(EMC)要求

This part of IEC 60974 specifies a) applicable standards and test methods for radio-frequency (r.f.) emissions; b) applicable standards and test methods for harmonic current emission, voltage fluctuations and flicker; c) immunity requirements and test methods for continuous and transient, conducted and radiated disturbances including electrostatic discharges. This standard is applicable to equipment for arc welding and allied processes, including power sources and ancillary equipment, for example wire feeders, liquid cooling systems and arc striking and stabilizing devices. NOTE 1 Allied processes are, for example, plasma cutting and arc stud welding. NOTE 2 This standard does not specify basic safety requirements for arc welding equipment such as protection against electric shock, unsafe operation, insulation coordination and related dielectric tests. Arc welding equipment type tested in accordance with, and which has met the requirements of, this standard is considered to be in compliance for all applications.

Arc welding equipment - Part 10: Electromagnetic compatibility (EMC) requirements

UL 123-2007 氧燃气焊枪

These requirements cover oxy-fuel gas torches used in operations such as welding, cutting, heating, scarfing, powder cutting, or other allied processes. These requirements do not apply to torches in which the fuel gas aspirates atmospheric air or to metal-spraying torches. A product that contains features, characteristics, components, materials, or systems new or different from those covered by the requirements in this standard, and that involves a risk of fire or of electric shock or injury to persons shall be evaluated using appropriate additional component and end-product requirements to maintain the level of safety as originally anticipated by the intent of this standard. A product whose features, characteristics, components, materials, or systems conflict with specific requirements or provisions of this standard does not comply with this standard. Revision of requirements shall be proposed and adopted in conformance with the methods employed for development, revision, and implementation of this standard.

UL Standard for Safety for Oxy-Fuel Gas Torches Eleventh Edition; Reprint with revisions through and including December 20, 2007

KS B ISO 7286:2007 电阻焊接设备的图形符号.

이 규격은 장비를 사용하는 사람에게 지시하기 위한 표시와 작업자의 조정 등 저항 용접 장비

Graphical symbols for resistance welding equipment

SANS 2503:2007 气体焊接设备.压力为300巴以下的焊接、切割和相关工艺用气瓶压力调节器

Specifies requirements for single or two-stage pressure regulators for connections to gas cylinders normally used for compressed gases up to 300 bar, for dissolved acetylene, for liquefied petroleum gases (LPG), methylacetylene-propadiene-mixtures (MPS) and carbon dioxide (CO2) used in welding, cutting and allied processes.

Gas welding equipment - Pressure regulators for gas cylinders used in welding, cutting and allied processes up to 300 bar

NF A85-009-4:2007 电弧焊接设备.第4部分:在役检查和试验

Arc welding equipment - Part 4 : in-service inspection and testing.

BS EN 60974-4:2007 弧焊设备.运行期间的检验和测试

This part of IEC 60974 specifies test procedures for in-service inspection and, after repair, to ensure electrical safety. These test procedures are also applicable for maintenance. This standard is applicable to power sources together with ancillary equipment for arc welding, cutting and allied processes built in conformity with IEC 60974-1. This standard is not applicable to testing of new power sources or engine-driven power sources.

Arc welding equipment - In-service inspection and testing

AWS D16.2M/D16.2-2007 机器人和自动弧焊组件安装指南

During the process of welding, metal vapors are produced in the electric arc. As these vapors cool and solidi@, a fume is formed that may be a potential health hazard to the welder and to others working in the same area. Such fine aerosols are all irritating to the respiratory system. Yet some fumes may potentially be more dangerous than others because of the specific substances present.

Guide for Components of Robotic and Automatic Arc Welding Installations

ANSI/AWS D16.2M/D16.2:2007 机器人和自动焊接的元部件

AWS/NEMA D16.2M/D16.2:200X, Guide for Components of Robotic and Automatic Arc Welding Installations, provides performance recommendations for evaluating components of a typical robotic or automatic welding installation. Emphasis is placed on the role of the welding interface. A pin arrangement and specific pin function for each location in a standardized 37-pin connector are proposed.

Components of Robotic and Automatic Welding

KS B ISO 18276:2006 焊接材料.高强度钢的气体保护和非气体保护金属极电弧焊用药芯电极.分类

이 규격은 고강도 강을 금속 아크 용접함에 있어 사용되는 가스 보호용 및 비가스 보호용 튜

Welding consumables-Tubular cored electrodes for gas-shielded and non-gas-shielded metal arc welding of high-strength steels-Classification

KS B ISO 18279:2006 钎焊.钎焊接头的缺陷

규격은 브레이징 접합부에서 발생할 수 있는 결함들의 등급을 규정하고 있다. 품질 등급에 대

Brazing-Imperfections in brazed joints