J64 焊接与切割设备 标准查询与下载

KS B ISO 18279:2006 钎焊.钎焊接头的缺陷

규격은 브레이징 접합부에서 발생할 수 있는 결함들의 등급을 규정하고 있다. 품질 등급에 대

Brazing-Imperfections in brazed joints

SANS 60974-7:2006 电弧焊设备．第7部分：吹管

Specifies safety and construction requirements for torches for arc welding and allied processes.

Arc welding equipment Part 7: Torches

IEC 60974-4:2006 电弧焊设备.第4部分:使用中的检验和测试

This part of IEC 60974 specifies test procedures for in-service inspection and, after repair, to ensure electrical safety. These test procedures are also applicable for maintenance. This standard is applicable to power sources together with ancillary equipment for arc welding, cutting and allied processes built in conformity with IEC 60974-1. This standard is not applicable to testing of new power sources or engine-driven power sources. NOTE For a power source not built in accordance with IEC 60974-1, see Annex

Arc welding equipment - Part 4: In-service inspection and testing

IEC 60947-4:2006 电弧焊接设备.第4部分:运行中检查和试验

Arc welding equipment - Part 4: In-service inspection and testing

ISO 12176-1:2006 塑料管材和管件.聚乙烯系统的熔接设备.第1部分:对熔接法

This part of ISO 12176 specifies the general characteristics of, and performance requirements for, equipment for butt fusion jointing of polyethylene (PE) piping systems using electrically powered heater plates. It is applicable to mechanical and pressure-activated equipment for butt fusion jointing PE pipes and fittings either intended to be used for the supply of gaseous fuels, conforming to ISO 4437 and ISO 8085-2, or intended for the conveyance of water for human consumption (including raw water prior to treatment) and for the conveyance of water for general purposes, conforming to ISO 4427-2 and ISO 4427-3. The normal ambient-temperature range in which the butt fusion machine is intended to operate is -10 M to +40 M ■ Use outside this temperature range will need to be agreed between the user and the supplier of the machine. Butt fusion machines with an automatic controller are subject to additional requirements as given in Annex A.

Plastics pipes and fittings - Equipment for fusion jointing polyethylene systems - Part 1: Butt fusion

JIS C 9300-6:2006 电弧焊接设备.第6部分:有限工作时间手动金属弧焊电源

この規格は，最大定格溶接電流160A以下の温度遮断装置を具備した限定使用率の被覆アーク溶接電源を構成すろための安全事項及び性能の必要事項について規定する。

Arc welding equipment -- Part 6: Limited duty manual metal arc welding power sources

JIS C 9300-1:2006 弧焊设备.第1部分:弧焊电源

この規格は。工業用及び専門家用に設計され，交流電源を入力とし，又はエンジンで駆動する方式のアーク溶接電源並ぴにプラズマ切断電源の安全にかかわる構造及び性能について規定する。

Arc welding equipment -- Part 1: Arc welding power sources

BS EN ISO 5172:2006+A1:2012 气焊设备. 气体焊接, 加热和切割用吹管. 规范和试验

Gas welding equipment. Blowpipes for gas welding, heatingand cutting. Specifications and tests

DLA A-A-59459 VALID NOTICE 1-2006 电脑数字控制(CNC)工具和切割机磨床

A-A-59459, dated 15 December 1999, has been reviewed and determined to be valid for use in acquisition.

GRINDING MACHINE, TOOL AND CUTTER, COMPUTER NUMERICAL CONTROL(CNC)

DIN EN 1256:2006 气焊设备.焊接、切割和相关工艺设备用软管组件规范

This document specifies performance and test requirements of hose assemblies, if supplied in assembled condition for equipment for gas welding, cutting and allied processes using rubber hose in complaince with EN 559.

Gas welding equipment - Specification for hose assemblies for equipment for welding, cutting and allied processes; English version of DIN EN 1256:2006-04

ARINC 671-2006 转变到焊接维护和修理指南

GUIDANCE FOR THE TRANSITION TO LEAD-FREE SOLDERING, MAINTENANCE, AND REPAIR

GUIDANCE FOR THE TRANSITION TO LEAD-FREE SOLDERING, MAINTENANCE, AND REPAIR

BS EN 1256:2006 气焊设备.焊接、切割和相关工艺用软管组件规范

This European Standard specifies performance and test requirements of hose assemblies, if supplied in assembled condition for equipment for gas welding, cutting and allied processes using rubber hoses in compliance with EN 559. This European Standard is not applicable to hose assemblies where the hoses are not in compliance with EN 559 (e.g. high pressure hoses).

Gas welding equipment - Specification for hose assemblies for equipment for welding, cutting and allied processes

KS C IEC 60974-10:2006 弧焊设备.第10部分:电磁兼容性(EMC)要求

이 규격은 아크용접 및 관련 과정에 대한 설비에 적용된다. 여기에는 전력전원을 비롯하여 급

Arc welding equipment-Part 10:Electromagnetic compatibility(EMC) requirements

KS C IEC 60974-6:2006 弧焊设备.第6部分:限制负载设备

이 규격은 제한된 효율을 지닌 수동 금속 아크 용접을 위한 열 컷아웃장치에 대한 전원에 적

Arc welding equipment-Part 6:Limited duty manual metal arc welding power sources

BS EN ISO 22827-1:2006 Nd:YAG激光束焊接机器的验收试验.带光纤送的机器.激光装配

This part of ISO 22827 specifies basic requirements and test methods for acceptance testing of high-power (average power more than 100 W), lamp-pumped or laser-diode-pumped Nd:YAG laser beam welding machines for seam welding with optical fibre delivery systems. The requirements can also be applied as a part of verification testing as part of maintenance, as appropriate. If modifications are made to a laser beam machine (rebuilding, repairs, modifications to the operating conditions, etc.) that have an effect on the acceptance testing, a repeat test may be necessary to cover the machine parameters affected by such modifications. This part of ISO 22827 applies to the beam generating system, the optical delivery system and the devices for shielding and assist gases. NOTE The moving mechanism is covered by ISO 22827-2. This part of ISO 22827 can be applied as a part of the acceptance conditions for the delivery of the optic laser beam welding cell.

Acceptance tests for Nd:YAG laser beam welding machines - Machines with optical fibre delivery - Laser assembly

NF A85-009-1:2006 弧焊设备.第1部分:焊接电源

Arc welding equipment - Part 1 : welding power sources.

NF A85-009-7:2006 弧焊设备.第7部分:焊枪

Arc welding equipment - Part 7 : torches.

DIN EN ISO 22827-1:2006 Nd:YAG激光射线焊接机器的加速试验.带光纤传送的机器.第1部分:激光装配(ISO 22827-1-2005).德文版本 EN ISO 22827-1-2005

This International Standard specifies basic requirements and test methods for acceptance testing of high-power (average power more than 100W), lamp-pumped or laser-diode-pumped Nd:YAG laser beam welding machines for seam welding with optical fiber delivery systems.

Acceptance tests for Nd:YAG laser beam welding machines - Machines with optical fibre delivery - Part 1: Laser assembly (ISO 22827-1:2005); English version of DIN EN ISO 22827-1:2006-02

DIN ISO 12166:2006 电阻焊设备.汽车工业中多点焊接用带一个副线圈的变压器的特殊规范 (ISO 12166-1997)

The purpose of this International Standard is to give specific details or to complement ISO 5826, which deals with general specifications applicable to all transformers, relating to particular transformers within its field of application. Unless otherwise specified, those requirements of ISO 5826 not modified by this International Standard are applicable. This International Standard applies to transformers with one secondary winding for multi-spot welding machines as used in the automobile industry. These transformers can substitute transformers covered by ISO 7284 for applications with current control. They can also replace transformers covered by ISO 7284 if only one secondary winding is used. Transformers covered by this International Standard shall be designed as to a) allow separate control and regulation of one single secondary welding circuit; b) allow substitution of one transformer covered by ISO 7284 by two transformers covered by this International Standard. NOTE -- By agreement between the manufacturer and the user, this International Standard may also be applied also for other industries or for other welding machines or applications where possible. ISO 5826 is applicable in all cases.

Resistance welding equipment - Particular specifications applicable to transformers with one secondary winding for multispot welding, as used in the automobile industry (ISO 12166:1997)

DIN ISO 10656:2006 电阻焊接.焊枪用集成变压器(ISO 10656-1996, 包括技术勘误表 1-2000)

This International Standard specifies transformers for electric resistance welding used in welding guns with intergrated transformers (robot guns). For these transformers it supplements the requirements given in ISO 5826 which remain applicable when not amended in this International Standard.

Electric resistance welding - Integrated transformers for welding guns (ISO 10656:1996, including Technical Corrigendum 1:2000);English version of DIN ISO 10656:2006-02