J64 焊接与切割设备 标准查询与下载

DIN EN ISO 15616-2:2003 高质量焊接和切割用CO2激光机验收试验.第2部分:静态和动态精度测定

This part of this standard is applicable to the measurement of the manipulation system precision, the positioning accuracy, the repeatability of positioning and the contour exactness for the acceptance tests for CO-laser machines for welding and cutting in two operation directions (2D) according to EN ISO 15616-1. This standard includes specifications of the testing procedure, the testing bench, and the testing itself.

Acceptance tests for CO₂-laser beam machines for high quality welding and cutting - Part 2: Measurement of static and dynamic accuracy (ISO 15616-2:2003); German version EN ISO 15616-2:2003

DIN EN ISO 15616-1:2003 高质量焊接和切割用CO2激光机验收试验.第1部分:通则和验收条件

This part of the standard is applicable to CO-laser beam machines for welding and cutting in two operating directions (2D). The main purpose of this standard is to provide requirements for acceptance testing of CO-laser beam machines prior to or during installation at the user's premises. The acceptance tests are used to document the ability of CO-laser beam machines to produce welded joints and cuts of consistent quality.

Acceptance tests for CO₂-laser beam machines for high quality welding and cutting - Part 1: General principles, acceptance conditions (ISO 15616-1:2003); German version EN ISO 15616-1:2003

KS C 2508-2003 流脂助焊接材料

이 규격은 주로 전기 기기, 전자 기기, 통신 기기 등의 배선 접속 및 부품의 제조 등에

Resin flux cored solders

BS EN 559:2003 气焊设备.焊接、切割和相关工艺用橡胶软管

This European Standard specifies requirements for rubber hoses, including twin hoses and fluxed fuel gas hoses for welding, cutting and allied processes. The term "allied processes" means, in particular, heating, brazing and metallization. This standard specifies requirements for rubber hoses for normal duty up to 2 MPa (20 bar) and light duty [limited to hoses for maximum operating pressure up to 1 MPa (10 bar) and with nominal bore less than or equal to 6,3 mm]. This standard pertains to hoses operated at temperatures - 20 ℃ to + 60 ℃. Thermoplastic hoses specified in EN 1327 are excluded from this standard. Different colours and markings are specified for identification of the gas. NOTE If hoses for liquefied petrol gases are used without regulators the use of light duty rubber hoses is not allowed. This standard applies to hoses used in: — gas welding and cutting; — arc welding under the protection of an inert or active gas; — processes allied to welding and cutting; and assembled according to EN 1256. Hose connections for the manufacture of hose lines see EN 560. This standard does not apply to hoses used for high pressure acetylene [more than 0,15 MPa (1,5 bar)].

Gas welding equipment - Rubber hoses for welding, cutting and allied processes

BS EN 60974-6:2003 电弧焊设备.有限任务手动金属电弧焊电源

This part of IEC 60974 is applicable to power sources with a thermal cut-out device for manual metal arc welding with limited duty. These welding power sources are mainly used by laymen. This part of IEC 60974 specifies safety requirements for construction and performance requirements of welding power sources, limited to a rated maximum welding current of 160 A. This part of IEC 60974 is not applicable to: — rotating welding power sources; — welding power sources with remote control; — welding power sources incorporating frequency conversion.

Arc welding equipment - Limited duty manual metal arc welding power sources

IEC 60974-1/AMD2:2003 电弧焊设备.第1部分:焊接电源.修改2

Arc welding equipment - Part 1: Welding power sources; Amendment 2

SANS 60974-1:2003 电弧焊设备．第1部分：焊接电源

Applicable to power sources for arc welding and allied processes designed for industrial and professional use, and supplied by a voltage as specified, or driven by mechanical means. Specifies safety requirements for construction and performance requireme

Arc welding equipment Part 1: Welding power sources

KS C IEC PAS 62170:2003 焊线模拟标准

이 규격은 집적 회로(IC) 다이로부터 구형(ball) 또는 쐐기(wedge)형 와이어

Bond wire modeling standard

KS C IEC PAS 62174:2003 通孔固定装置的焊接温度抗性

이 규격은 스루홀 장착의 캡슐 봉합 고체 상태 소자가 웨이브 납땜이나 납땜 인두를 이용

Resistance to soldering temperature for through-hole mounted devices

BS EN ISO 15616-1:2003 高质量焊接和切割用CO2激光束机的验收试验.通用原则和验收条件

ISO 15616-1:2003 is applicable to CO2-laser beam machines for welding and cutting in two operating directions. The main purpose of this International Standard is to provide requirements for acceptance testing of CO2-laser beam machines prior to or during installation at the user's premises. The acceptance tests are used to document the ability of CO2-laser beam machines to produce welded joints and cuts of consistent quality. ISO 15616-1:2003 is intended to be used for preparation of the technical specification for CO2-laser beam machines for high quality welding and cutting in two operating directions. It specifies basic requirements. However, this International Standard may also be used for testing as part of maintenance, as appropriate.

Acceptance tests for CO2- laser beam machines for high quality welding and cutting - General principles, acceptance conditions

BS EN ISO 15616-3:2003 高质量焊接和切割用CO2激光束机的验收试验.气体流量和压力测量仪的校正

ISO 15616-3:2003 is applicable to the measurement of the process-oriented gas parameters for the acceptance tests for CO2-laser beam machines for high quality welding and cutting in two operation directions in accordance with ISO 15616-1:2003. This international Standard specifies examination procedures for instruments used for control of process-oriented gas parameters.

Acceptance tests for CO2- laser beam machines for high quality welding and cutting - Calibration of instruments for measurement of gas flow and pressure

BS EN ISO 15616-2:2003 高质量焊接和切割用CO2激光束机的验收试验.静态和动态精确度的测定

ISO 15616-2:2003 is applicable to the measurement of the precision of the manipulation system, the positioning accuracy, the repeatability of positioning and the trajectory exactness for the acceptance testing of CO2-laser beam machines for high quality welding and cutting in two operation directions in accordance with ISO 15616-1:2003. This International Standard specifies testing procedure and equipment and establishes a classification system for the motion system related to the required precision for the application being used.

Acceptance tests for CO2- laser beam machines for high quality welding and cutting - Measurement of static and dynamic accuracy

NF A84-340-1:2003 气焊设备.安全装置.第1部分:安装回火(逆燃)制止器

Gas welding equipment - Safety devices - Part 1 : incorporating a flame (flashback) arrestor.

NF A84-340-2:2003 气焊设备.安全装置.第2部分:不安装回火(逆燃)制止器

Gas welding equipment - Safety devices - Part 2 : not incorporating a flame (flashback) arrestor.

ISO 15616-2:2003 高质量焊接和切割用CO2激光射线机的验收试验.第2部分:静态和动态准确度的测定

This Part of this European Standard is applicable to the measurement of: — the precision of the manipulation system; — the positioning accuracy; — the repeatability of positioning; — the trajectory exactness, for the acceptance testing of CO2-laser beam machines for high quality welding and cutting in two operation directions (2D) in accordance with EN ISO 15616-1. This standard specifies the testing procedure and equipment. The scope of the examination and the grades of precision shall be stated in the technical specification for the CO2- laser beam machine and be in accordance with the application requirements due to the diversity of the requirements to the laser system. The work piece and/or the optics are moved during laser beam processing. The movement of the work piece and/or the optics require a certain precision in the motion system, e.g. moving working table, rotary fixture, moving laser optics, etc. to achieve producible results. This standard establishes a classification system for the motion system related to the required precision for the application being used.

Acceptance tests for CO₂-laser beam machines for high quality welding and cutting - Part 2: Measurement of static and dynamic accuracy

ISO 15616-3:2003 高质量焊接和切割用CO2激光射线机的验收试验.第3部分:气体流量和压力测量仪的校正

This Part of this European Standard is applicable to the measurement of the process oriented gas parameters for the acceptance tests for CO2-laser beam machines for high quality welding and cutting in two operation directions (2D) in accordance with EN ISO 15616-1. This standard specifies examination procedures for instruments used for control of process oriented gas parameters.

Acceptance tests for CO₂-laser beam machines for high quality welding and cutting - Part 3: Calibration of instruments for measurement of gas flow and pressure

IEC 60793-1-49:2003 光学纤维.第1-49部分:测量方法和试验程序.差分模延迟

Describes a method for characterizing the modal structure of a graded-index multimode fibre. The information is useful for assessing the bandwidth performance of a fibre when used with laser sources. Applies only to multimode, graded-index glass-core (ca

Optical fibres - Part 1-49: Measurement methods and test procedures; Differential mode delay

ISO 15616-1:2003 高质量焊接和切割用CO2激光射线机的验收试验.第1部分:通用原理和验收条件

This Part of this European Standard is applicable to CO2-laser beam machines for welding and cutting in two operating directions (2D). The main purpose of this standard is to provide requirements for acceptance testing of CO2-laser beam machines prior to or during installation at the user's premises. The acceptance tests are used to document the ability of CO2-laser beam machines to produce welded joints and cuts of consistent quality. This standard is intended to be used for preparation of the technical specification for CO2-laser beam ma-chines for high quality welding and cutting in two operating directions (2D). This standard specifies basic requirements. Additional tests and requirements may be specified in the technical specification for the CO2- laser beam machine. NOTE 1 The technical specification for the CO2-laser beam machine usually forms a part of the contract and it is agreed by the parties concerned (the manufacturer of the CO2-laser beam machine and the customer/user). NOTE 2 The requirements may be too stringent for non-high quality cutting. However, the standard may also be used for testing as part of maintenance, as appropriate. If modifications are made to a CO2-laser beam machine (rebuilding, repairs, modifications to the oper-ating conditions etc.) that may have an effect on the acceptance testing, repeat test may be neces-sary covering the machine parameters affected by such modifications. If a CO2-laser beam machine that has already been accepted is dismantled (e.g. in order to change its location) such tests may involve verification according to the requirements in 6.4 as a minimum.

Acceptance tests for CO₂-laser beam machines for high quality welding and cutting - Part 1: General principles, acceptance conditions

BS EN 60974-2:2003 弧焊设备.液体冷却系统

This part of IEC 60974 specifies safety and construction requirements for liquid cooling systems intended to cool torches. These liquid cooling systems can be internal or external to power sources for arc welding and allied processes (see annex A). This standard is not applicable to refrigerated cooling systems.

Arc welding equipment - Liquid cooling systems

DIN EN 730-2:2003 气焊设备.安全装置.第2部分:无火焰(逆燃)制动器; 德文版本 EN 730-2:2002

Gas welding equipment - Safety devices - Part 2: Not incorporating a flame (flashback) arrestor; German version EN 730-2:2002