J64 焊接与切割设备 标准查询与下载

BS EN ISO 5183-1:2001 电阻焊接设备.外锥度1:10的电极适配器.锥度1:10的圆锥形固定件

This part of ISO 5183 specifies the dimensions and tolerances of resistance spot welding electrode adaptors where the fixing element for the cap (see ISO 5821) is a male taper of 1:10 and for which the electrode taper fits in conformance with ISO 1089.

Resistance welding equipment - Electrode adaptors, male taper 1: 10 - Conical fixing, taper 1:10

BS EN ISO 14744-2:2001 焊接.电子束焊接机的验收检验.加速电压特性测量

This standard is intended for use when the characteristics of the accelerating voltage of electron beam welding machines complying with EN ISO 14744-1 is to be measured in connection with an aceptance inspection. It provides essential information on the procedure and apparatus to be used for making the measurements. The accelerating voltage is one of the significant parameters in electron beam welding. When accelerating the electrons, the voltage should be stable and reproducible within given short-term and long-term limits. The purpose of the measurement is thus to check whether the variations in accelerating voltage are within specified limits.

Welding. Acceptance inspection of electron beam welding machines. Measurement of accelerating voltage characteristics

BS EN ISO 14744-3:2001 焊接.电子束焊接机的验收检验.电子束电流特性的测量

This standard is intended for use when the beam current of electron beam welding machines complying with EN ISO 14744-1:2000 is to be measured in connection with an acceptance inspection. It provides essential information on the procedure and apparatus to be used for making the measurements. The beam current is one of the significant parameters in electron beam welding. When the beam current impinges on the workpiece, it should be stable and reproducible within given short-term and long-term limits. The purpose of the measurement is thus to check whether the variations in beam current are within these limits.

Welding. Acceptance inspection of electron beam welding machines. Measurement of beam current characteristics

BS EN ISO 14744-4:2001 焊接.电子束焊接机的验收检验.焊接速度的测量

This standard is intended for use when the welding speed for electron beam welding machines complying with EN ISO 14744-1 is to be measured in connection with an acceptance inspection. It provides essential information on the procedure and apparatus to be used for making the measurements. Alternative standardised procedures can be used, provided they have at least the same acceptance inspection as the welds specified in this part 4. The measured parameter is the speed of the translational and rotational movements required to perform the welding operation. The welding speed is one of the significant parameters in electron beam welding. The workpiece or the weld point shall thus be moved at a uniform speed, in a reproducible manner, within given short-term and long-term limits. The purpose of the measurement is to check whether the variations in welding speed are maintained within these limits.

Welding. Acceptance inspection of electron beam welding machines. Measurement of welding speed

BS EN ISO 14744-6:2001 焊接.电子束焊接机的验收检验.现场位置稳定性的测量

This standard is intended for use when the stability of spot stability of welding machines complying with EN ISO 14744-1 is to be measured in connection with an acceptance inspection. It provides essential information to the procedure and apparatus to be used for making the measurements. The stability of the spot position is a particularly significant parameter for prolonged welding applications and for electron beam welding with automatic devices positioning the workpiece. In such applications, the welding machine shall be able to reproduce, over prolonged periods and without additional correction of the position being required, a given beam-to-joint alignment. The purpose of measurement is to check whether and to what extent the electron beam generated by a welding machine keeps within the range of limit deviations specified for the spot position.

Welding. Acceptance inspection of electron beam welding machines. Measurement of stability of spot position

ISO 5828:2001 电阻焊设备 连接水冷接头的二次连接电缆 尺寸及特性

This International Standard specifies dimensions and characteristics of secondary connecting cables which are air-cooled over their length and with terminals connected to water-cooled lugs. The secondary connecting cables are used for connection between the secondary terminals of a welding transformer and the electrode holders.

Resistance welding equipment - Secondary connecting cables with terminals connected to water-cooled lugs - Dimensions and characteristics

ISO 12176-3:2001 塑料管材和管件 聚乙烯系统的熔焊接设备 第3部分：操作者标记

This part of ISO 12176 describes the format and the contents of a fusion operator's badge. The operator's badge is used during the construction of polyethylene (PE) piping systems for gas supply to identify the fusion operator. The operator's badge can be used to activate or deactivate the fusion-jointing equipment or to identify the operator. The objective of this part of ISO 12176 is to achieve international interoperability between the operator's badge and the card-reading equipment of fusion-jointing equipment conforming to ISO 12176-1 or ISO 12176-2. The fusion-jointing equipment is required to read either the bar code or the magnetic-stripe code of the badge and to call up the corresponding data within the equipment in a standard format.

Plastics pipes and fittings - Equipment for fusion jointing polyethylene systems - Part 3: Operator's badge

AWS D16.3M/D16.3-2001 机器人电弧焊风险评估导则

This specification addresses processing and quality control requirements for electron beam welding. Processing includes both high- and low-voltage welding equipment and high and medium vacuum variations.

Risk Assessment Guide for Robotic Arc Welding

AWS D17.1-2001 航天应用熔焊规范 整合勘误-2001年7月

This standard makes use of both the U.S. Customary Units and the International System of Units (SI). The latter is shown within brackets or in appropriate columns in tables and figures. The measurements may not be exact equivalents; therefore, each system shall be used independently.

Specification for Fusion Welding for Aerospace Applications Second Printing- Incorporating Errata [Superseded: SAE AMS-STD-1595A, SAE AMS-STD-1595]

AWS G1.10M-2001 气焊气焊挤压和加热设备热塑对焊评价指南

These guidelines list and describe defects in welded

Guide for The Evaluation of Hot Gas, Hot Gas Extrusion, and Heated Tool Butt Thermoplastic Welds

AWS F2.2-2001 镜头遮光罩选择器

The data to support this Standard Welding Procedure Specification (SWPS) have been derived from the above listed Procedure Qualification Records (PQRs) which were reviewed and validated under the auspices of the Welding Research Council.

Lens Shade Selector

DIN 32508:2000 带自制氢和制氧装置的微型钎焊机和焊机.机械和气体技术要求、试验和标记

The document applies to devices for microsoldering and microwelding (MWS) devices), in which a stoichiometric hydrogen/oxygen mixture is generated by the electrolytic decomposition of water with a gas rate limit by 500 L/h. Also covered are all the gas lines, gas mixer, gas purifier, safety devices and blowpipe required for the operation of the MWS device.

Micro devices for brazing and welding with own hydrogen and oxygen production - Mechanical and gas engineering requirements, test, marking

BS EN 12573-1:2000 焊接非静压热塑罐.一般原理

This standard specifies general principles for welded static non-pressurized thermoplastic tanks. It applies to work shop and site fabrications. The standard covers tanks with a capacity of 0,45 m(450 litres) and above. Tanks which comply with the requirements of this standard are not intended to withstand internal pressure or vacuum other than that which may occur during the transfer of fluids (including gases) in their normal operation. This standard applies to tanks fabricated in the following thermoplastics: Polyethylene (PE) Polypropylene (PP) Poly (vinyl chloride) (PVC) Poly (vinylidene fluoride) (PVDF) NOTE: Design data for these materials is given in EN 1778.

Welded static non-pressurized thermoplastic tanks - General principles

IEC 60974-1:2000 电弧焊设备.第1部分:焊接电源

Arc welding equipment - Part 1: Welding power sources

CSA E60974-1-00-CAN/CSA-2000(R2005) 弧焊设备.第1部分:焊接电源

This Standard applies to the safety of such equipment designed to be installed and used in accordance with the rules of the Canadian E/ectrica/ Code, Part 1. Products covered by the scope of this Standard are also subject to the requirements of CSA Standard C22.2 No. 0.

Arc welding equipment-Part 1:Welding power sources

DIN EN ISO 14744-4:2000 焊接.电子束焊接机的验收检验.第4部分:焊接速度的测量

Welding - Acceptance inspection of electron beam welding machines - Part 4: Measurement of welding speed (ISO 14744-4:2000); German version EN ISO 14744-4:2000

DIN EN ISO 14744-3:2000 焊接.电子束焊接机的验收检验.第3部分:电子束电流特性的测量

For the acceptance test of electron beam welding machines the measurement of the parameter beam current is precribed by requirements for measuring design, of measuring process and measuring evaluation. The beam current is an important physical rating for the electron beam welding.#,,#

Welding - Acceptance inspection of electron beam welding machines - Part 3: Measurement of beam current characteristics (ISO 14744-3:2000); German version EN ISO 14744-3:2000

DIN EN ISO 14744-2:2000 焊接.电子束焊接机的验收检验.第2部分:加速电压特性的测量

Welding - Acceptance inspection of electron beam welding machines - Part 2: Measurement of acceleration voltage characteristics (ISO 14744-2:2000); German version EN ISO 14744-2:2000

DIN EN ISO 14744-6:2000 焊接.电子束焊接机验收检验.第6部分:焊点位置稳定性的测量

For the acceptance test of electron beam welding the test of the welding point position tolerances is specified. The welding point position tolerance is a variable which is, above all, important for long welding times and for electron beam welding with automatic movements to the welding positioning. The measuring design, measuring process and measuring evaluation are specified.#,,#

Welding - Acceptance inspection of electron beam welding machines - Part 6: Measurement of stability of spot position (ISO 14744-6:2000); German version EN ISO 14744-6:2000

DIN EN ISO 14744-5:2000 焊接.电子束焊接机验收检验.第5部分:偏转精度的测量

For acceptance test for electron beam welding machines specifications are given for movement accuracy of peripheral equipments such as work table and positioner. The measuring evaluation and the measuring process (in all relevant moving axes and moving directions) are laid down.

Welding - Acceptance inspection of electron beam welding machines - Part 5: Measurement of run-out accuracy (ISO 14744-5:2000); German version EN ISO 14744-5:2000