J90 活塞式内燃机与其它动力设备综合 标准查询与下载

KS B 6230-2005 多管圆筒形换热器

이 규격은 KS B 6733에 따라서 만들어진 일반 산업용[클래스 I(1) 상당], 화학

Shell and tube heat exchangers

BS ISO 7967-7:2005 往复式内燃机.零部件和系统词汇.调节系统

This part of ISO 7967 defines terms relating to governing systems for reciprocating internal combustion (RIC) engines. This part of ISO 7967 mainly deals with speed governing systems for RIC engines. For governing systems based on other parameters (e.g. torque, temperature and load), the definitions given may be considered as a basis. ISO 2710-1 gives a classification of RIC engines and defines basic terms of such engines and their characteristics. NOTE The term Speed Governor may apply to an individual unit conventionally mounted on an engine or to a combination of units comprising a speed control system.

Reciprocating internal combustion engines - Vocabulary of components and systems - Governing systems

ISO/PAS 22241-1:2005 柴油机发动机.氮氧化物还原剂AUS 32.第1部分:质量要求

Diesel engines - NOx reduction agent AUS 32 - Part 1: Quality requirements

ISO/PAS 22241-2:2005 柴油机发动机.氮氧化物还原剂AUS 32.第2部分:试验方法

Diesel engines - NOx reduction agent AUS 32 - Part 2: Test methods

JIS B 8004:2005 往复式内燃机.发动机功率测量的方法和测定.依据ISO 8178的废气排放试验的补充要求

この規格は，住復動内燃機関の出力決定方法においてJIS B 8008の規格群に従って排気排出物測定を行うときの追加要求事項について規定する。基本的な共通要求事項は，共通規格(Core standard)であるJIS B 8003で規定する。

Reciprocating internal combustion engines -- Determination and method for the measurement of engine power -- Additional requirements for exhaust emission tests in accordance with ISO 8178

JIS B 8003:2005 内燃机.发动机功率测量的方法和测定.一般要求

1.1この規格は，商取引を目的に生産する液体燃料又はガス燃料を用いる内燃機関の標準大気条件，出力・燃料消費量・潤滑油消費量の表示及び試験方法について規定する。

Internal combustion engines -- Determination and method for the measurement of engine power -- General requirements

JIS K 2247-1:2005 柴油发动机.NOx减速添加剂AUS 32.第1部分:特性

この規格は，ディーゼル機関搭載車両に装着する選択還元式触媒コンバータ(以下，SCRコンバータという。)の作動に必要なNOx還元添加剤AUS 32(以下，AUS 32という。)の性状について規定する。 SCRコンバータは.ディーゼル機関から排出される窒素酸化物(NOx)を選択的に低減するのに特に適している。

Diesel engines -- NOx reduction additive AUS 32 -- Part 1: Properties

JIS B 8002-1:2005 往复式内燃机.性能.第1部分:功率、燃料和润滑油消耗量的说明和试验方法.通用发动机的附加要求

この規格は，共通規格であるJIS B 8003に規定する基本的な機関出力の決定方法及び測定方法の共通要求事項に加えて，一般機関に対する出力・燃料消費量・潤滑油消費量の表示及び試験方法に関する追加要求事項について規定する。

Reciprocating internal combustion engines -- Performance -- Part 1: Declarations of power, fuel and lubricating oil consumptions, and test methods -- Additional requirements for engines for general use

BS ISO 7967-8:2005 往复式内燃机.零部件和系统词汇.起动系统

This part of ISO 7967 defines terms relating to starting systems for reciprocating internal combustion engines. A diagram showing the relationship between the various types of starting system is given in Figure 1. ISO 2710 gives a classification of reciprocating internal combustion engines and defines basic terms of such engines and their characteristics.

Reciprocating internal combustion engines - Vocabulary of components and systems - Starting systems

DIN 70070:2005 柴油发动机.NOx-还原剂AUS 32.质量要求

This standard specifies the quality characteristics of the reduction agent which are necessary for the operation of SCR catalysts in motor vehicles with Diesel engines. SCR catalysts are particularly suitable for the reduction of NOx emission from Diesel engines

Diesel engines - NOx-Reduction agent AUS 32 - Quality requirements

JIS B 8008-1 ERRATUM 1:2005 勘误

ERRATUM

ASTM D1384-05e1 玻璃器皿中发动机冷却剂腐蚀试验的标准试验方法

This test method will generally distinguish between coolants that are definitely deleterious from the corrosion standpoint and those that are suitable for further evaluation. However, the results of this test method cannot stand alone as evidence of satisfactory corrosion inhibition. The actual service value of an engine coolant formulation can be determined only by more comprehensive bench, dynamometer, and field tests.1.1 This test method covers a simple beaker-type procedure for evaluating the effects of engine coolants on metal specimens under controlled laboratory conditions (seeAppendix X1). Note 1For more information on engine coolants, see (Refs 1-8).1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific hazards statements are given in 10.1.7.2, 10.1.7.3, and 10.1.7.4.

Standard Test Method for Corrosion Test for Engine Coolants in Glassware

ASTM D6593-05a 评定低温和轻负荷条件下运行的以汽油为燃料的火花点火式内燃机中使用的抑制沉积物形成的汽车机油的标准试验方法

1.1 This test method is commonly referred to as the Sequence VG test and has been correlated with vehicles used in stop-and-go service prior to 1996, particularly with regard to sludge and varnish formation179. It is one of the test methods required to evaluate oils intended to satisfy the API SL performance category.1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific hazard statements are given in 7.7, 7.10.2.2, 8.3.4.2, 8.4.4.3, 9.2.6, 9.3.4.5, 12.1.1.7,12.2.1.4, and Annex A1.

Standard Test Method for Evaluation of Automotive Engine Oils for Inhibition of Deposit Formation in a Spark-Ignition Internal Combustion Engine Fueled with Gasoline and Operated Under Low-Temperature, Light-Duty Conditions

ASTM D1384-05 玻璃器皿中发动机冷却剂腐蚀试验的标准试验方法

1.1 This test method covers a simple beaker-type procedure for evaluating the effects of engine coolants on metal specimens under controlled laboratory conditions (see Appendix X1). Note 18212;For more information on engine coolants, see (Refs 1-8)178;.1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific hazards statements are given in 10.1.7.2, 10.1.7.3, and 10.1.7.4.

Standard Test Method for Corrosion Test for Engine Coolants in Glassware

ASTM D7156-05 评定T-11废气再循环柴油发动机内柴油的标准试验方法

1.1 This test method covers an engine test procedure for evaluating diesel engine oils for performance characteristics in a diesel engine equipped with exhaust gas recirculation, including viscosity increase and soot concentrations (loading). This test method is commonly referred to as the Mack T-11.1.2 The values stated in either SI or inch-pound units are to be regarded separately as the standard. Within the test method, the inch-pound units are shown in parentheses when combined with SI units. The only exception is where there is no direct SI equivalent such as screw threads, national pipe threads/diameters, and tubing sizes. 1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. See Annex A6 for specific Safety Precautions

Standard Test Method for Evaluation of Diesel Engine Oils in the T-11 Exhaust Gas Recirculation Diesel Engine

ASTM D1177-05 含水发动机冷却剂凝固点的标准试验方法

1.1 This test method covers the determination of the freezing point of an aqueous engine coolant solution in the laboratory.Note 18212;Where solutions of specific concentrations are to be tested, they shall be prepared from representative samples as directed in Test Methods D 1176. Secondary phases separating on dilution need not be separated.Note 28212;These products may also be marketed in a ready-to-use form (prediluted).1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Freezing Point of Aqueous Engine Coolants

ASTM D6593-05 评定低温和轻负荷条件下运行的以汽油为燃料的火花点火式内燃机中使用的抑制沉积物形成的汽车机油的标准试验方法

1.1 This test method is commonly referred to as the Sequence VG test and has been correlated with vehicles used in stop-and-go service prior to 1996, particularly with regard to sludge and varnish formation179. It is one of the test methods required to evaluate oils intended to satisfy the API SL performance category.1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific hazard statements are given in 7.7, 7.10.2.2, 8.3.4.2, 8.4.4.3, 9.2.6, 9.3.4.5, 12.1.1.7,12.2.1.4, and Annex A1.

Standard Test Method for Evaluation of Automotive Engine Oils for Inhibition of Deposit Formation in a Spark-Ignition Internal Combustion Engine Fueled with Gasoline and Operated Under Low-Temperature, Light-Duty Conditions

ASTM D5752-05 重型发动机用预充冷却剂中使用的补充冷却剂添加物(SCAs)的标准规范

1.1 This specification covers the general, physical, chemical, and performance requirements for Supplemental Coolant Additives (SCAs) at a precharged level in the cooling systems of heavy-duty engines. After precharging, SCAs are customarily used periodically to service cooling systems at 1/4 to 1/3 the precharged dosage to compensate for additives lost through dilution and depletion.1.2 The SCA products meeting this specification are intended for use with water, with recommended dilutions of coolant concentrates, with prediluted engine coolants, or to upgrade the performance of light-duty engine coolants to meet the heav-duty requirements of Specification D 6210. Engine coolant products shall be of the low-silicate type and, if ethylene glycol based, shall meet Specification D 4985. Propylene glycol base low-silicate type coolant products may also be used, if these materials meet the chemical and performance requirements of Specification D 4985.1.3 The SCA concentrate, before dissolution, may be in either liquid, solid, or slurry form. The form is as agreed upon between the manufacturer and the user.1.4 The values stated in SI units are to be regarded as standard. The inch-pound units in parentheses are approximate equivalents provided for information only.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Supplemental Coolant Additives (SCAs) for Use in Precharging Coolants for Heavy-Duty Engines

KS B ISO 14269-5:2004 农业和林业用拖拉机和自驱动机械.操作室环境.第5部分:增压系统试验方法

이 규격은 환기 시스템을 가진 농림업용 트랙터와 자주식 기계의 운전실 내부에서 일관된

Tractors and self-propelled machines for agriculture and forestry－Operator enclosure environment－Part 5：Pressurization system test method

KS B ISO 14269-4:2004 农业和林业用拖拉机和自驱动机械.操作室环境.第4部分:空气过滤元件试验方法

이 규격은 운전실의 평판형 공기 필터의 성능 수준을 결정하기 위한 시험 방법을 규정한다

Tractors and self-propelled machines for agriculture and forestry-Operator enclosure environment-Part 4:Air filter element test method