J91 内燃机与附属装置 标准查询与下载

NF E37-211-6:2010 往复式内燃机.废气排放测量.第6部分:测量结果和试验报告.

Reciprocating internal combustion engines - Exhaust emission measurement - Part 6 : report of measuring results and test.

ISO 7967-5:2010 往复式内燃机.部件和系统词汇表.第5部分:冷却系统

This part of ISO 7967 establishes a vocabulary for the cooling systems of reciprocating internal combustion engines. ISO 2710 gives a classification of reciprocating internal combustion engines and defines basic terms of such engines and their characteristics.

Reciprocating internal combustion engines - Vocabulary of components and systems - Part 5: Cooling systems

ISO 7967-9:2010 往复式内燃机.组件和系统词汇表.第9部分:控制和监测系统

This part of ISO 7967 establishes a vocabulary for the control and monitoring systems of reciprocating internal combustion engines. ISO 2710 gives a classification of reciprocating internal combustion engines and defines basic terms of such engines and their characteristics.

Reciprocating internal combustion engines - Vocabulary of components and systems - Part 9: Control and monitoring systems

JB/T 10957-2010 内燃机用快速接头

本标准主要适用于内燃机制造与检测用快速接头。适用流体包括汽油、柴油、水和空气等。 本标准适用于不锈钢、黄铜材料制管接头，其他材料制管接头也可参照使用本标准。 本标准规定了内燃机用快速接头的型号、种类、技术要求、试验方法、检查、标志、包装、运输及贮存等。

Quick-action couplings used for internal combustion engines

JB/T 11014-2010 通用小型汽油机密封性能.技术要求与试验方法

本标准规定了通用小型汽油机密封性能的技术要求、试验方法和检验规则。 本标准适用于功率不大于30kW的往复活塞式汽油机。 本标准不适用于摩托车汽油机、舷外机等特殊用途的汽油机。

Technical requirements and test methods on seal performance of general utility small gasoline engines

JB/T 9744-2010 内燃机.零、部件磁粉检测

本标准规定了内燃机零、部件磁粉检测方法的术语和定义、人员要求、检测设备、检测介质、观察条件、零件表面的要求、磁化条件、磁化方法、磁化规范、磁化时的注意事项、检测方法、退磁和清洗。 本标准适用于钢铁磁性材料制造的成品、半成品和原材料表面及近表面缺陷的检测，并作为制定磁粉检测操作规程的依据。

Internal combustion engines-Magnetic particle inspection for parts and components

JB/T 11036-2010 单缸燃气机.技术条件和试验方法

本标准规定了燃用天然气或液化石油气的单缸燃气机的技术要求、试验方法、检验规则及标志、包装、运输和贮存等。对燃用其他气体燃料的单缸燃气机可参照本标准执行。 本标准适用于燃用气体燃料的火花点燃式单缸往复式燃气机(以下简称单缸燃气机)。

Single cylinder gas engines-General requirements and test methods

BS ISO 3046-4:2009 往复式内燃机.性能.速度调节

Reciprocating internal combustion engines - Performance - Speed governing

DIN EN ISO 14314:2010 往复式内燃机.反冲起动设备.一般安全要求(ISO 14314-2004).德文版本EN ISO 14314-2009

The document specifies requirements for re-coil starting equipment used on reciprocating internal combustion engines for land, rail and marine use, excluding engines used to propel road vehicles and air craft. The document may be applied to engines used to propel construction, earth moving machines and for other applications where no suitable international standards exist. In addition to the technical safety requirements, it contains the method of checking the adherence to these requirements.

Reciprocal internal combustion engines - Recoil starting equipment - General safety requirements (ISO 14314:2004); German version EN ISO 14314:2009

ANSI/ASTM F2876:2010 危险地点内燃机的安装操作规程

Practice for the Installation of Internal Combustion Engines in Hazardous Locations

ASTM D7468-10b 康明斯ISM测试的标准试验方法

This test method was developed to assess the performance of an engine oil to control engine wear and deposits under heavy-duty operating conditions selected to accelerate soot generation, valve train wear, and deposit formation in a turbocharged, aftercooled four-stroke-cycle diesel engine equipped with exhaust gas recirculation hardware. This test method may be used for engine oil specification acceptance when all details of this test method are in compliance. Applicable engine oil service categories are included in Specification D4485. The design of the engine used in this test method is representative of many, but not all, modern diesel engines. This factor, along with the accelerated operating conditions needs to be considered when extrapolating test results.1.1 The test method covers a heavy-duty diesel engine test procedure conducted under high soot conditions to evaluate oil performance with regard to valve train wear, top ring wear, sludge deposits, and oil filter plugging in an EGR environment. This test method is commonly referred to as the Cummins ISM Test. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.2.1 Exception8212;The only exception is where there is no direct SI equivalent such as screw threads, national pipe threads/diameters, tubing sizes, or where there is a sole source of supply equipment specification. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. See Annex A1 for general safety precautions.

Standard Test Method for Cummins ISM Test

ANSI/ABYC H-25-2010 便携式汽油燃油系统

This standard is a guide for the design, construction, and stowage of portable tanks with related fuel lines and accessories comprising a portable gasoline fuel system for boats.

Portable Gasoline Fuel Systems

ISO 3046-4:2009 往复式内燃机.性能.第4部分:调速

Reciprocating internal combustion engines - Performance - Part 4: Speed governing

BS EN ISO 11102-1:2009 往复式内燃机.手柄起动装置.安全要求和试验

Reciprocating internal combustion engines - Handle starting equipment - Safety requirements and tests

KS B 7372-2009 小型陆地用水冷却柴油机

이 표준은 연속 정격 출력 22kW 이하의 농용 및 육용 일반 동력용의 수랭 4사이클 디젤

Small size water cooled diesel engines for land use

JIS B 8002-3:2009 往复式内燃机.性能.第3部分:试验测量

Reciprocating internal combustion engines -- Performance -- Part 3: Test measurements

JIS B 8008-2:2009 往复式内燃机.废气排放测量.第2部分:现场条件下气体和颗粒物质排放的测量

Reciprocating internal combustion engines -- Exhaust emission measurement -- Part 2: Measurement of gaseous and particulate exhaust emissions under field conditions

BS ISO 8178-4:2007 往复式内燃机.废气排放量测量.不同用途发动机的稳态试验循环

Reciprocating internal combustion engines - Exhaust emission measurement - Steady-state test cycles for different engine applications

BS ISO 8178-5:2008 往复式内燃机.废气排放测量.试验燃料

Reciprocating internal combustion engines - Exhaust emission measurement - Test fuels

BS ISO 8178-2:2008 往复式内燃机.废气排放度量.现场条件下气体和颗粒尾气污染物排放的测量

Reciprocating internal combustion engines - Exhaust emission measurement - Measurement of gaseous and particulate exhaust emissions under field conditions