J91 内燃机与附属装置 标准查询与下载

SANS 10219-1:2006 工业内燃机的性能（净动力）的测定．第1部分：标准参比条件和动力，燃料消耗和滑油消耗量的宣称

Specifies the standard reference conditions and the methods of declaring the power, fuel consumption and lubricating oil consumption of reciprocating internal conbustion engines using liquid or gaseous fuels.

The determination of performance (at net power) of industrial internal combustion engines Part 1: Standard reference conditions and declarations of power, fuel consumption and lubricating oil consumption

SANS 10219-6:2006 工业内燃机的性能（净动力）的测定．第6部分：超速保护

Covers a procedure for the protection of reciprocating internal combustion engines against damage caused by high engine speeds. Where necessary, individual requirements can be given for particular engine applications.

The determination of performance (at net power) of industrial internal combustion engines Part 6: Overspeed protection

SANS 10219-5:2006 工业内燃机的性能（净动力）的测定．第5部分：扭转振动

Covers a procedure for ensuring that torsional vibrations in shaft systems of sets driven by reciprocating internal combustion engines are kept within specified limits.

The determination of performance (at net power) of industrial internal combustion engines Part 5: Torsional vibrations

WJ 1768-2006 柴油机组件名称及其代号编制原则和方法

Principles and methods for compiling names of diesel engine components and their codes

KS B 6008-2005 陆地用小型柴油机性能试验方法

이 규격은 주로 농공용 및 육용 일반 동력용 소형 디젤 엔진(이하 엔진이라 한다.)의 성능

Test method of performance of small size diesel engines for land use

NAVY QPL-J1899-2-2005 活塞式飞机发动机的润滑油(无灰分散剂)

This list has been prepared for use by or for the Government in the acquisition of products covered by the subject non-Government standard and such listing of a product is not intended to and does not connote endorsement of the product by the Department of Defense. All products listed herein have been qualified under the requirements for the product as specified in the latest adopted issue of the applicable non-Government standard. This list is subject to change without notice; revision or amendment of this list will be issued as necessary. The listing of a product does not release the manufacturer from compliance with the non-Government standard requirements.

LUBRICATING OIL, AIRCRAFT PISTON ENGINE, (ASHLESS DISPERSANT)

NAVY QPL-J1966-2-2005 活塞式飞机发动机的润滑油(无分散剂矿物油)

The Military Grade designations are being phased-out in favor of the NATO Code Numbers. Commercial Grade designations are being replaced by the SAE Grade classifications. The SAE Grade of each approved product is included in its Qualification Reference Number (QNR) listed above, i.e. the number which follows the dash correspondes directly to the SAE Grade.

LUBRICATING OIL, AIRCRAFT PISTON ENGINE (NON-DISPERSANT MINERAL OIL)

DLA MIL-I-25026 B VALID NOTICE 2-2005 MJ-4型发动机排气用热电偶温度计

The activities above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http://assist.daps.dla.mil.

INDICATOR, TEMPERATURE, THERMOCOUPLE, ENGINE EXHAUST, TYPE MJ-4

NF E37-506*NF ISO 19860:2005 燃气轮机.燃气轮机装置的数据获取和趋势监控系统要求

Gas turbines - Data acquisition and trend monitoring system requirements for gas turbine installations.

DLA A-A-59334 VALID NOTICE 1-2005 横轴工具室(精密度)和发动机(规格)机床 [代替:DLA MIL-L-13896 E CANC 通告 1,DLA MIL-L-13896 E,DLA MIL-L-13896 D REINST 通告 2,DLA MIL-L-13896 D CANC 通告 1,DLA MIL-L-13896 D(2),DLA MIL-L-13896 D(1)]

The activities above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http://assist.daps.dla.mil

LATHE, ENGINE (STANDARD) AND TOOLROOM (PRECISION), HORIZONTAL SPINDLE [Superseded: DLA MIL-L-13896 E CANC NOTICE 1, DLA MIL-L-13896 E, DLA MIL-L-13896 D REINST NOTICE 2, DLA MIL-L-13896 D CANC NOTICE 1, DLA MIL-L-13896 D (2), DLA MIL-L-13896 D (1)

DLA MS51067 REV D VALID NOTICE 2-2005 11／16英寸普通宽度V型零件发动机带

The activities above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http://assist.daps.dla.mil

BELTS, V: ENGINE ACCESSORY DRIVE (11/16 INCH NOMINAL WIDTH)

DLA MS51066 REV D VALID NOTICE 2-2005 0．500英寸普通宽度V型零件发动机带

The activities above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http://assist.daps.dla.mil

BELTS, V: ENGINE ACCESSORY DRIVE (0.500 INCH NOMINAL WIDTH)

DLA MS51065 REV D VALID NOTICE 2-2005 0．380英寸普通宽度V型零件发动机带

The activities above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http://assist.daps.dla.mil

BELT, V: ENGINE ACCESSORY DRIVE (0.380 INCH NOMINAL WIDTH)

DLA MS51069 REV D VALID NOTICE 2-2005 7／8英寸普通宽度V型零件发动机带

The activities above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http://assist.daps.dla.mil

BELTS, V: ENGINE ACCESSORY DRIVE (7/8 INCH NOMINAL WIDTH)

DLA MS51070 REV D VALID NOTICE 2-2005 1英寸普通宽度V型零件发动机带

The activities above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http://assist.daps.dla.mil

BELTS, V: ENGINE ACCESSORY DRIVE (1 INCH NOMINAL WIDTH)

DLA MS51068 REV D VALID NOTICE 2-2005 3／4英寸普通宽度V型零件发动机带

The activities above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http://assist.daps.dla.mil

BELTS, V: ENGINE ACCESSORY DRIVE (3/4 INCH NOMINAL WIDTH)

ISO 7967-1:2005 往复式内燃机.零部件和系统词汇.第1部分:固定件和外部罩盖

This part of ISO 7967 defines terms relating to engine structural components and external covers of reciprocating internal combustion engines. ISO 2710 gives a classification of reciprocating internal combustion engines and defines basic terms of such engines and their characteristics.

Reciprocating internal combustion engines - Vocabulary of components and systems - Part 1: Structure and external covers

ISO 7967-6:2005 往复式内燃机.零部件和系统词汇.第6部分:润滑系统

This part of ISO 7967 defines terms relating to lubricating systems. ISO 2710 gives a classification of reciprocating internal combustion engines and defines basic terms of such engines and their characteristics.

Reciprocating internal combustion engines - Vocabulary of components and systems - Part 6: Lubricating systems

ISO 7967-7:2005 往复式内燃机.零部件和系统词汇.第7部分:调节系统

This part of ISO 7967 defines terms relating to governing systems for reciprocating internal combustion (RIC) engines. This part of ISO 7967 mainly deals with speed governing systems for RIC engines. For governing systems based on other parameters (e.g. torque, temperature and load), the definitions given may be considered as a basis. ISO 2710-1 gives a classification of RIC engines and defines basic terms of such engines and their characteristics. NOTE The term Speed Governor may apply to an individual unit conventionally mounted on an engine or to a combination of units comprising a speed control system.

Reciprocating internal combustion engines - Vocabulary of components and systems - Part 7: Governing systems

ISO 7967-8:2005 往复式内燃机.零部件和系统词汇.第8部分:起动系统

This part of ISO 7967 defines terms relating to starting systems for reciprocating internal combustion engines. A diagram showing the relationship between the various types of starting system is given in Figure 1. ISO 2710 gives a classification of reciprocating internal combustion engines and defines basic terms of such engines and their characteristics.

Reciprocating internal combustion engines - Vocabulary of components and systems - Part 8: Starting systems