J92 机体与运动件 标准查询与下载

JB/T 6729-2007 内燃机.曲轴、凸轮轴磁粉检测

本标准规定了内燃机曲轴、凸轮轴磁粉检测和评定方法。 本标准适用于气缸直径小于或等于200mm的往复式内燃机曲轴、凸轮轴表面及近表面缺陷的检验和评定。

Internal combustion engines.Magnetic particle inspection for crankshafts and camshafts

JB/T 7292.2-2007 内燃机衬套 凸轮轴衬套 技术条件

本标准规定了内燃机双金属卷制凸轮轴衬套的结构型式、技术要求、检验规则及标志、包装、运输和贮存。 本标准适用于气缸直径为20mm以内的往复式内燃机卷制凸轮轴衬套。 用整体单层材料制成的内燃机凸轮轴衬套，可参照JB/T 7292.3执行。

Internal combustion engine bushes-Camshaft bushes-Speciflcation

JB/T 7292.1-2007 内燃机衬套 连杆衬套 技术条件

本标准规定了内燃机整体单层连杆衬套的结构型式、技术要求、检验规则及标志、包装、运输和贮存。 本标准适用于气缸直径为20mm以内的往复式内燃机整体单层连杆衬套。 本标准不适用于内燃机卷制连杆衬套。

Internal combustion engine bushes Connecting-rod small-end bushes Specification

JB/T 7292.3-2007 内燃机衬套 摇臂衬套 技术条件

本标准规定了内燃机整体单层摇臂衬套的结构型式、技术要求、检验规则及标志、包装、运输和贮存。 本标准适用于气缸直径为200mm以内的往复式内燃机整体单层摇臂衬套。 用双金属材料卷制的内燃机摇臂衬套，可参照JB/T 7292.2执行。

Internal combustion engine bushes-Rocker bushes-Speciflcation

JB/T 7293-2007 内燃机 主轴承盖螺栓与螺母 技术条件

本标准规定了内燃机主轴承盖螺栓与螺母的技术要求、检验规则、标志与包装。 本标准适用于气缸直径20mm以下的往复活塞式内燃机主轴承盖螺栓与螺母（以下简称螺栓螺母）。

Internal combustion engines-Main bearing lid bolts and nuts-Speciflcation

JB/T 5084-2007 内燃机.曲轴止推垫圈技术条件

本标准规定了内燃机曲轴止推垫圈的术语、代号与结构型式、技术要求、检验方法、检验规则和标志、包装、运输和贮存。 本标准适用于气缸直径200mm以下的往复活塞式内燃机曲轴止推垫圈（以下简称止推垫圈）。

Internal combustion engines.Crankshaft thrust washers.Specification

ANSI Z21.81-2004, Z 21.81a-2006 汽缸连接装置用标准(同CSA 6.25 (R201x))

Standard for Cylinder Connection Devices (same as CSA 6.25 (R201x))

ASTM A983/A983M-06(2016) 用于中速柴油机的连续颗粒流锻碳和合金钢曲轴的标准规格

1.1 This specification covers continuous grain flow forged carbon and alloy steel crankshafts for medium speed diesel and natural gas engines. 1.2 The steel used in the manufacture of the forgings is required to be vacuum degassed. 1.3 The choice of steel composition grade for a given strength class is normally made by the forging supplier, unless otherwise specified by the purchaser. 1.4 Provision is made for treatment of designated surfaces of the crankshaft to provide enhanced fatigue strength, or wear resistance, or both. 1.5 Except as specifically required in this specification, all provisions of Specification A788/A788M apply. 1.6 Unless the order specifies the applicable “M” specification designation, the material shall be furnished to the inch-pound units. 1.7 The values stated in either inch-pound units or SI (metric) units are to be regarded separately as standard. Within the text and tables the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the specification.

Standard Specification for Continuous Grain Flow Forged Carbon and Alloy Steel Crankshafts for Medium Speed Diesel Engines

KS R ISO 18669-1:2005 内燃发动机.活塞销.第1部分:通用规范

이 규격은 왕복 운동형 내연 기관용의 바깥지름 8 mm로부터 100 mm까지의 피스톤 핀

Internal combustion engines-Piston pins-Part 1:General specifications

KS R ISO 18669-2:2005 内燃发动机.活塞销.第2部分:检验测量原理

이 규격은 피스톤 핀을 측정하기 위하여 사용되는 측정 원리를 정의한 것이다. 이것은 왕복

Internal combustion engines-Piston pins-Part 2:Inspection measuring principles

GJB 931A-2005 装甲车辆柴油发动机曲轴用方钢规范

本规范规定了装甲车辆柴油发动机曲轴用方钢的要求、质量保证规定、交货准备及说明事项等。 本规范适用于制造装甲车辆柴油发动机曲轴用边长为150mm～185mm的热轧、锻制方钢。

Specification for square steels for diesel engine crankshafts of armour vehide

ISO 6621-5:2005 内燃机.活塞环.第5部分:质量要求

This part of ISO 6621 specifies those quality aspects that are capable of definition but not normally found on a drawing specification. It covers the following: — single-piece piston rings of grey cast iron or steel; — multi-piece piston rings (oil control rings) consisting of cast iron parts and spring components; — single-piece and multi-piece oil control rings of steel, i.e. oil control rings in the form of strip steel components or steel segments (rails) with spring expander components. In addition to specifying certain of the limits of acceptance relating to inspection measuring principles (covered by ISO 6621-2), this part of ISO 6621 also covers those features for which no recognized quantitative measurement procedures exist and which are only checked visually with normal eyesight (spectacles if worn normally) and without magnification. Such features (superficial defects) are additional to the standard tolerances of ring width, radial wall thickness and closed gap. This part of ISO 6621 does not establish acceptable quality levels (AQL), it being left to manufacturer and client to decide the appropriate levels jointly. In this case, the recommendations of ISO 2859 are followed. This part of ISO 6621 specifies the quality requirements of piston rings for both reciprocating internal combustion engines and compressors working under analogous conditions. It is applicable to all such rings of a diameter ≤ 200 mm.

Internal combustion engines - Piston rings - Part 5: Quality requirements

SAE AIR1828B-2005 发动机润滑系统监控指南

The purpose of this SAE Aerospace Information Report (AIR) is to provide information and guidance for the selection and use of oil system monitoring devices and methods. This AIR is intended to be used as a technical guide. It is not intended to be used as a legal document or standard. The scope of this document is limited to those inspection and analysis methods and devices that can be considered appropriate for routine maintenance.

(R) Guide to Engine Lubrication System Monitoring

JB/T 6289-2005 内燃机.铸造铝活塞.金相检验

本标准规定了内燃机铸造共晶铝-硅合金和铝-硅-铜-镁合金活塞的金相组织级别、检验及评定方法。 本标准适用于气缸直径小于或等于200mm的内燃机铸造共晶铝-硅合金和铝-硅-铜-镁合金活塞经热处理后的金相组织检验。

Internal combustion engines - Casting aluminium pistons - Metallographic inspection

JB/T 5083-2005 内燃机.干式铸铁气缸套.技术条件

本标准规定了内燃机干式铸铁气缸套的术语、技术要求、检验规则与检验方法，标志、包装、运输和贮存。 本标准适用于气缸直径小于或等于150mm的往复活塞式内燃机干式铸铁气缸套(以下简称气缸套)。

Internal combustion engines - Dry cast-iron cylinder liners - Specifications

ASTM A472/A472M-05 蒸汽涡轮机轴及转子锻件的热稳定性用标准试验方法

1.1 This test method covers the determination of heat stability of steam turbine shafts and rotor forgings to ensure stability at operating temperature. This test method is not ordinarily applicable to generator rotor forgings.1.2 This test method is expressed in both inch-pound unit and in SI units; however, unless the purchase order or contract specifies the applicable M specification designation (SI units), the inch-pound units shall apply. The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the test method, the SI units as shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.1.3 Supplementary requirements of an optional nature are provided for use at the option of the purchaser. The supplementary requirements shall apply only when specified individually by the purchaser in the purchase order or contract.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Heat Stability of Steam Turbine Shafts and Rotor Forgings

ISO 18669-1:2004 内燃发动机.活塞销.第1部分:一般规范

This part of ISO 18669 specifies the essential dimensional characteristics of piston pins of outer diameter from 8 mm up to 100 mm, for reciprocating internal combustion engines. In addition, it establishes a vocabulary, a pin-type classification, material description based on mechanical properties, common features and quality requirements. It may also be used for piston pins of compressors working under analogous conditions. In certain applications, except road vehicles, and provided that mutual agreement is made between the purchaser and the manufacturer, this part of ISO 18669 may be used with suitable modifications.

Internal combustion engines - Piston pins - Part 1: General specifications

ISO 18669-2:2004 内燃发动机.活塞销.第2部分:检验测量原理

This part of ISO 18669 defines the measuring principles to be used for measuring piston pins; it applies to piston pins from 8 mm up to and including 100 mm outside diameter for reciprocating internal combustion engines and compressors. In certain applications, except road vehicles, and provided that mutual agreement is made between the purchaser and the manufacturer, this part of ISO 18669 may be used with suitable modifications.

Internal combustion engines - Piston pins - Part 2: Inspection measuring principles

JB/T 10406-2004 内燃机 激光淬火气缸套 技术条件

本标准规定了内燃机激光淬火铸铁气缸套的技术要求、检验规则与检验方法、标志、包装、运输和贮存。 　　本标准适用于气缸直径小于或等于200mm的往复式内燃机激光淬火铸铁气缸套。

Internal combustion engines - Laser surface hardened cylinder liners - Specifications

JB/T 10407-2004 内燃机 铝活塞奥氏体铸铁镶圈 金相检验

本标准规定了内燃机铝活塞奥氏体铸铁镶圈的金相组织级别、检验及评定方法。 　　本标准适用于气缸直径小于或等于20mm的往复活塞式内燃机铝活塞奥氏铸铁镶圈的金相组织检验。

Metallographic test for piston with austenitic carrier insert of internal combustion engine