J94 燃油供给系统 标准查询与下载
共找到 494 条与 燃油供给系统 相关的标准，共 33 页
This International Standard specifies the dimensions, necessary for interchangeability, of tapers for the shaft ends and hubs of fuel injection pumps on diesel (compression-ignition) engines. The shaft ends and hubs specified can be used either with or without woodruff keys, and for other applications for which no specific standards exist.
Diesel engines - Fuel injection pumps - Tapers for shaft ends and hubs
- ICS
- 43.060.40
- CCS
- J94
- 发布
- 2004-12-01
- 实施
- 2004-12-01
This part of ISO 13555 specifies a test rig and reference method for the validation of timing measurement devices which, by application of the pressure-sensing principle on the high-pressure fuel injection pipe, are used for checking the dynamic setting of fuel injection equipment fitted to diesel engines. (In order to produce a realistic measurement situation, the test rig allows the addition of vibrational excitation of the high-pressure fuel injection pipe —deemed a primary source of signal corruption when used on running diesel engines.) The validation procedure can be used either in the initial approval of a timing measurement device or the verification of its proper functioning when already in use. The aim is to ensure that the devices supplied by different manufacturers provide comparable measurement results.
Diesel engines - Procedure for checking the dynamic timing of diesel fuel injection equipment - Validation of timing devices
- ICS
- 43.060.40
- CCS
- J94
- 发布
- 2004-12-01
- 实施
- 2004-12-01
本部分规定了中、小功率柴油机活塞式输油泵总成的性能试验方法。 本部分适用于中、小功率柴油机合成式喷油泵总成中的输油泵，对有特殊要求的输油泵，也可参照使用。
Plunger type fuel feed pump Part 2: Performance test method
- ICS
- 43.060.40
- CCS
- J94
- 发布
- 2004-10-20
- 实施
- 2005-04-01
本部分规定了中、小功率柴油机活塞式输油泵总成的技术要求、检验规则、标志、包装、运输和贮存等要求。 本部分适用于中、小功率柴油机合成式喷油泵总成中的输油泵，对有特殊要求的输油泵，也可参照使用本部分或按协议执行。
Plunger type fuel feed pump Part 1: Technical specifications
- ICS
- 43.060.40
- CCS
- J94
- 发布
- 2004-10-20
- 实施
- 2005-04-01
本部分规定了中、小功率柴油机喷油泵出油阀偶件的性能试验方法。 本部分适用于中、小功率柴油机喷油泵出油阀偶件。
Delivery valve of diesel fuel injection pump Part 2: Performance test method
- ICS
- 43.060.40
- CCS
- J94
- 发布
- 2004-10-20
- 实施
- 2005-04-01
本部分规定了中、小功率柴油机喷油泵出油阀偶件的技术要求、检验规则、标志、包装、运输和贮存等要求。 本部分适用于中、小功率柴油机喷油泵出油阀偶件。
Delivery valve of diesel fuel injection pump Part 1: Technical specifications
- ICS
- 43.060.40
- CCS
- J94
- 发布
- 2004-10-20
- 实施
- 2005-04-01
本部分规定了中、小功率柴油机喷油泵柱塞偶件的性能试验方法。 本部分适用于中、小功率柴油机喷油泵柱塞偶件。
Plunger of diesel fuel injection pump Part 2: Performance test method
- ICS
- 43.060.40
- CCS
- J94
- 发布
- 2004-10-20
- 实施
- 2005-04-01
本部分规定了中、小功率柴油机喷油泵柱塞偶件的技术要求、检验规则、标志、包装、运输和贮存等要求。 本部分适用于中、小功率柴油机喷油泵柱塞偶件。
Plunger of diesel fuel injection pump Part 1: Technical specifications
- ICS
- 43.060.40
- CCS
- J94
- 发布
- 2004-10-20
- 实施
- 2005-04-01
Oil-fired warm air furnaces Third Edition; Update No. 1
Oil-fired warm air furnaces Third Edition; Update No. 1
- ICS
- CCS
- J94
- 发布
- 2004-09-01
- 实施
This part of ISO 13555 specifies a test rig and reference method for the validation of timing measurement devices which, by application of the pressure-sensing principle on the high-pressure fuel injection pipe, are used for checking the dynamic setting of fuel injection equipment fitted to diesel engines. (In order to produce a realistic measurement situation, the test rig allows the addition of vibrational excitation of the high-pressure fuel injection pipe —deemed a primary source of signal corruption when used on running diesel engines.) The validation procedure can be used either in the initial approval of a timing measurement device or the verification of its proper functioning when already in use. The aim is to ensure that the devices supplied by different manufacturers provide comparable measurement results.
Diesel engines - Procedure for checking the dynamic timing of diesel fuel injection equipment - Part 3: Validation of timing measurement devices
- ICS
- 43.060.40
- CCS
- J94
- 发布
- 2004-07
- 实施
本标准规定了中、小功率柴油机用柱塞式喷油泵总成、分配式喷油泵、喷油器总成、活塞式输油泵、供油角度自动提前器产品清洁度限值及测定方法。 本标准适用于中、小功率柴油机用喷油泵、分配式喷油泵、喷油器总成、输油泵及提前器。
Limits and determination of cleanliness for diesel fuel injection equipment
- ICS
- 27.020
- CCS
- J94
- 发布
- 2004-06-17
- 实施
- 2004-11-01
本部分规定了与柴油机喷油泵直接连接的机械离心式供油角度自动提前器的性能试验方法。 本部分适用于柴油机喷油泵用提前器性能试验。
Automatic timing-advance of diesel fuel injection pump - Part 2: Performance test method
- ICS
- 27.020
- CCS
- J94
- 发布
- 2004-06-17
- 实施
- 2004-11-01
本部分规定了与柴油机喷油泵直接连接的机械离心式供油角度自动提前器的技术要求、检验规则、标志、包装、运输和贮存等要求。 本部分适用于柴油机喷油泵用提前器。
Automatic timing-advance of diesel fuel injection pump - Part 1: Technical specifications
- ICS
- 27.020
- CCS
- J94
- 发布
- 2004-06-17
- 实施
- 2004-11-01
Les normes de l’Association canadienne de normalisation (CSA) sont élaborées selon un processus consensuel et approuvées par le Conseil canadien des normes. Ce processus rassemble des volontaires représentant différents intérêts et points de vue dans le
Oil-Firing Appliances: General Requirements Third Edition
- ICS
- CCS
- J94
- 发布
- 2004-04-01
- 实施
This part of ISO 7876 establishes a vocabulary for high-pressure pipes and end-connections in fuel injection systems for diesel (compression-ignition) engines. These high-pressure pipes and end-connections are used in fuel injection systems worldwide and require precise terminology. NOTE When the word “fuel” is used in the terms listed it can be omitted providing there can be no misunderstanding.
Fuel injection equipment - Vocabulary - Part 4: High-pressure pipes and end-connections
- ICS
- 01.040.43;43.060.40
- CCS
- J94
- 发布
- 2004-04
- 实施
This International Standard specifies the dimensions, necessary for interchangeability, of tapers for the shaft ends and hubs of fuel injection pumps on diesel (compression-ignition) engines. The shaft ends and hubs specified can be used either with or without woodruff keys, and for other applications for which no specific standards exist.
Diesel engines - Fuel injection pumps - Tapers for shaft ends and hubs
- ICS
- 43.060.40
- CCS
- J94
- 发布
- 2004-03
- 实施
This part of ISO 8535 specifies the dimensions of, and gives requirements for, composite steel tubes for high-pressure fuel injection pipes used on diesel (compression-ignition) engines (Class 2) and for fuel injection pump testing (Class 1).
Compression ignition engines - Steel tubes for high pressure fuel injection pipes - Requirements for composite tubes
- ICS
- 43.060.40
- CCS
- J94
- 发布
- 2004-02-10
- 实施
- 2004-02-10
ISO 19438:2003 specifies a multi-pass filtration test, with continuous contaminant injection and using the on-line particle counting method, for evaluating the performance of fuel filters for internal combustion engines submitted to a constant flow rate of test liquid. The test procedure determines the contaminant capacity of a filter, its particulate removal characteristics and differential pressure. ISO 19438:2003 is applicable to filter elements having a rated flow of between 50 l/h and 800 l/h; however, by agreement between filter manufacturer and customer, and with some modification, the procedure is permitted for application to fuel filters with higher flow rates.
Diesel fuel and petrol filters for internal combustion engines - Filtration efficiency using particle counting and contaminant retention capacity
- ICS
- 43.060.40
- CCS
- J94
- 发布
- 2004-01-07
- 实施
- 2004-01-07
This European Standard specifies general performance requirements for ergonomics, innocuousness, size designation, ageing, compatibility and marking of protective clothing and the information to be supplied by the manufacturer with the protective clothing.
Protective clothing - General requirements
- ICS
- 13.340.10
- CCS
- J94
- 发布
- 2004-01-02
- 实施
- 2004-01-02
Les normes de l’Association canadienne de normalisation (CSA) sont élaborées selon un processus consensuel et approuvées par le Conseil canadien des normes. Ce processus rassemble des volontaires représentant différents intérêts et points de vue dans le
Oil-fired hot air generators Update No. 1
- ICS
- CCS
- J94
- 发布
- 2004-01-01
- 实施
