K10 电工材料和通用零件综合 标准查询与下载

ASTM B576-94(2005) 电接触材料的电弧侵蚀试验的标准指南

The significance of the variables set forth in this guide was proved by various laboratories using several test systems at test currents ranging from 100 to 35 000 A. These variables will be significant for any case where voltage and current are sufficient to produce arcing.1.1 This guide covers the major variables which affect the rate of arc erosion of electrical contact materials and serves as a guide in developing more detailed specifications for arc-erosion tests.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.1.2 Arc erosion testing involves some vaporization of material. It is the responsibility of the user to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet for the material being tested.

Standard Guide for Arc Erosion Testing of Electrical Contact Materials

SN/T 0232-1993 出口电线电缆检验规程

Rules of the inspection of cable andwire for export

UL 1773-1993 端子箱

Termination boxes

DIN VDE 0289-6:1993 电力设备用电缆、电线和软线的定义.附件

Definitions for cables, wires and flexible cords for power installation; accessories

WJ 2119-1993 透明导电膜规范

Transparent Conductive Film Specifications

KS C 2358-1993 热模压用云母板

이 규격은 가열 형조하여 전기절연에 사용하는 마이카 판에 대하여 규정한다.

Rigid mica materials for heat molding

KS C 3312-1992 丝包铜绕组线

이 규격은 전기기기의 권선 및 배선에 사용하는 횡권선에 대하여 규정한다.

Fiber or paper covered copper winding wires

prEN 61158-2-1992 工业控制系统用现场总线标准.第2部分:物理层规范和服务定义

Field bus standard for use in industrial control systems; part 2: physical layer specification and service definition

HD 46.3.3 S1-1992 绕组线的封装.第3部分:锥形输线轴.第3节:由热塑性材料制成的不能回收使用的输线轴规范

Packaging of winding wires; part 3: taper barrelled delivery spools; section 3: specifications for non-returnable spools made from thermoplastic material (IEC 264-3-3:1990)

KS C 2514-1992 一般电气绝缘线、槽、板

이 규격은 부피 저항률이 1.5μΩm 이하인 전기 저항용 합금 선, 조 및 판에 대하여 규

Electrical Resistance wires, Ribbons and Sheets for General Use

KS C 4523-1992 舌簧继电器

이 규격은 주파수 60Hz의 교류 300V 이하 또는 직류 300 V 이하의 전로에 사용하

Control Reed Relays

HD 405.1 S1 A1-1992 电缆火灾条件下的试验.第1部分:单股垂直绝缘导线或电缆的试验(IEC 332-1-79,修改件)

Tests on electric cables under fire conditions; part 1: test on a single vertical insulated wire or cable (IEC 332-1:1979, modified)

KS C 4531-1991 普通交流螺线管

이 규격은 60Hz 단상 교류 300V 이하의 전로에 각종 기구의 조작을 사용되는 적철

AC Solenoids of General Purpose

HD 490.5 S2-1991 绕组线的试验方法.第5部分:电特性(IEC 851-5-88+A1-90)

Methods of test for winding wires; part 5: electrical properties (IEC 851-5:1988 + A1:1990)

HD 405.2 S1-1991 电缆火灾条件下的试验.第2部分:单股小型垂直绝缘铜导线或电缆的试验(IEC 332-2-89)

Tests on electric cables under fire conditions; part 2: test on a single small vertical insulated copper wire or cable (IEC 332-2:1989)

DIN VDE 0472-814:1991 电缆、绝缘导线和软线的检验.第814部分:火情情况下隔离效应的持续性

Testing of cables, wires and flexible cords; continuance of isolation effect under fire conditions

DIN 4000-65:1991 第65部分:非成型切削工具 现成电线、设备连接线和多股接线用物品特性表格设计

Tabulator layouts of article characteristics make it possible that standardized and non-standardized articles which are similar to each other can be grouped, fined and selected. This standard deals with the following group of articles: standed connecting electric wires.#,,#

Tabular layouts of article characteristics for wires, equipment-wires and stranded connecting wires, ready-made

UL 1666-1991 电缆和纤维光缆垂直安装在竖井中时燃烧蔓延高度的测试

Test for flame propagation height of electrical and optical-fiber cables installed vertically in shafts

KS C 0301-1990 室内布线图形符号

이 규격은 일반 옥내 배선에서 전등.전력.통신.신호.재해방지.피뢰설비등의 배선, 기기 및

Graphical Symbols of Interior Wiring Diagram for Architectual Plans

KS C 6933-1990 多成分多模光纤

이 규격은 코어 및 클래드에 다성분계 유리를 사용한 스텝 인덱스형 다중 모드 광섬유 소선에

Multicomponent glass multimode optical fibers