K12 带绝缘层电线 标准查询与下载

NF C31-679/A1*NF EN 60317-29/A1:2010 特定型号绕组线的规范.第29部分:涂覆聚酰胺-酰亚胺的聚酯或聚酰胺酯漆包圆扁铜绕组线,200级.

Specifications for particular types of winding wires - Part 29 : polyester or polyesterimide overcoated with polyamide-imide enamelled rectangular copper wire, class 200.

IEC 60317-29:1990/AMD2:2010 特种绕组线规范.第29部分:200级聚酯或聚酰亚胺涂覆的聚酰胺-酰亚胺漆包扁圆线;修改件2

Specifications for particular types of winding wires - Part 29: Polyester or polyesterimide overcoated with polyamide-imide enamelled rectangular copper wire, class 200

IEC 60317-44:1997/AMD1:2010 特种绕组线规范.第44部分:240级芳族聚酰亚胺薄膜绕包矩形铜线.修改件1

Specifications for particular types of winding wires - Part 44: Aromatic polyimide tape wrapped rectangular copper wire, class 240; Amendment 1

IEC 60317-1:2010 特种绕组线规范.第1部分:105级聚乙烯醇缩醛漆包圆铜线

This Part of IEC 60317 specifies the general requirements of enamelled round copper winding wires of class 105 with a sole coating based on polyvinyl acetal resin, which may be modified providing it retains the chemical identity of the original resin and meets all specified wire requirements. NOTE A modified resin is a resin that has undergone a chemical change, or contains one or more additives to enhance certain performance or application characteristics. Class 105 is a thermal class that requires a minimum temperature index of 105 and a heat shock temperature of at least 155 °C

Specifications for particular types of winding wires - Part 1: Polyvinyl acetal enamelled round copper wire, class 105

IEC 60317-13:2010 特种绕组线规范.第13部分:200级聚酰胺-酰亚胺包敷聚酯或聚酯酰亚胺漆包圆铜线

This Part of IEC 60317 specifies the requirements of enamelled round copper winding wire of class 200 with a dual coating. The underlying coating is based on polyester or polyesterimide resin, which may be modified providing it retains the chemical identity of the original resin and meets all specified wire requirements. The superimposed coating is based on polyamideimide resin.

Specifications for particular types of winding wires - Part 13: Polyester or polyesterimide overcoated with polyamide-imide enamelled round copper wire, class 200

IEC 60317-8:2010 特种绕组线规范.第8部分:180级聚酯酰亚胺漆包圆铜线

This Part of IEC 60317 specifies the requirements of enamelled round copper winding wires of class 180 with a sole coating based on polyesterimide resin, which may be modified provided it retains the chemical identity of the original resin and meets all specified wire requirements.

Specifications for particular types of winding wires - Part 8: Polyesterimide enamelled round copper wire, class 180

IEC 60317-17:2010 特种绕组线规范.第17部分:105级聚乙烯醇缩醛漆包扁铜线

This part of IEC 60317 specifies the requirements of enamelled rectangular copper winding wire of class 105 with a sole coating based on polyvinyl acetal resin, which may be modified providing it retains the chemical identity of the original resin and meets all specified wire requirements.

Specifications for particular types of winding wires - Part 17: Polyvinyl acetal enamelled rectangular copper wire, class 105

IEC 60317-25:2010 特种绕组线规范 第25部分:200级聚酰胺-酰亚胺包敷聚酯或聚酯酰亚胺漆包圆铝线

This Part of IEC 60317 specifies the requirements of enamelled round aluminium winding wires of class 200 with a dual coating. The underlying coating is based on polyester or polyesterimide resin, which may be modified providing it retains the chemical identity of the original resin and meets all specified wire requirements. The superimposed coating is based on polyamide-imide resin.

Specifications for particular types of winding wires - Part 25: Polyester or polyesterimide overcoated with polyamide-imide, enamelled round aluminium wire, class 200

IEC 60317-12:2010 特种绕组线规范.第12部分:120级聚乙烯醇缩醛漆包圆铜线

This Part of IEC 60317 specifies the requirements of enamelled round copper winding wire of class 120 with a sole coating based on polyvinyl acetal resin, which may be modified providing it retains the chemical identity of the original resin and meets all specified wire requirements.

Specifications for particular types of winding wires - Part 12: Polyvinyl acetal enamelled round copper wire, class 120

DIN EN 60264-1:2010 绕组线的封装.第1部分:漆包圆绕组线(IEC 60264-1-1968+A1-2009).德文版本EN 60264-1-1994+A1-2009

This standard specifies the general requirements to the packaging of winding wires.

Packaging of winding wires - Part 1: Containers for round winding wires (IEC 60264-1:1968 + A1:2009); German version EN 60264-1:1994 + A1:2009

IEC 60317-18:2010 特种绕组线规范.第18部分:120级聚乙烯醇缩醛漆包矩形铜线

Specifications for particular types of winding wires - Part 18: Polyvinyl acetal enamelled rectangular copper wire, class 120

IEC 60317-22:2010 特种绕组线规范.第22部分:180级聚酰胺涂层的聚酯或聚酰亚胺漆包圆铜线

Specifications for particular types of winding wires - Part 22: Polyester or polyesterimide enamelled round copper wire overcoated with polyamide, class 180

IEC 60172:1987/AMD2:2010 漆包绕组线的温度指数测定用试验规程.修改件2

Test procedure for the determination of the temperature index of enamelled winding wires; Amendment 2

ASTM B802/B802M-10 钢心铝绞线(ACSR)用锌-5%铝稀土合金镀层钢芯线标准规范

1.1 This specification covers round, zinc–5 % aluminum-mischmetal (Zn–5Al–MM) alloy-coated, steel core wire with three classes of Zn–5Al–MM coating used for mechanical reinforcement in the manufacture of aluminum conductors, steel reinforced (ACSR). 1.2 This specification covers wire of diameter from 0.0500 to 0.1900 in. or 1.27 to 4.82 mm, inclusive. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

Standard Specification for Zinc-5% Aluminum-Mischmetal Alloy-Coated Steel Core Wire for Aluminum Conductors, Steel Reinforced (ACSR)

ANSI/ICEA S-85-625-2010 空芯聚烯烃绝缘铜导体通信电缆技术要求的ICEA标准

Thsi standard covers mechanical and electrical requirements for filled, polyolefin, copper conductor telecommunications cable. It provides alternative choices for type of insulation, core lay-ups, color code, sheath design (shielding materials, single or double jackets, and jacket thicknesses), and screened or non-screened core.

ICEA Standard for Telecommunications Cable Aircore, Polyolefin Insulation, Copper Conductor Technical Requirements

ASTM B971-10 预用作电子设施的镀银织带和缎带扁铜线的标准规范

1.1 This specification covers silver-coated copper braid and ribbon flat wire intended for electronic application (Explanatory Note 1). 1.2 Two classes of silver-coated braid and ribbon flat copper wire are covered as follows: 1.2.1 Class A8212;Annealed temper. 1.2.2 Class H8212;Hard-drawn. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3.1 Exceptions8212;The SI values for density, resistivity, and volume are to be regarded as standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Silver-Coated Braid and Ribbon Flat Copper Wire intended for use in Electronic Application

ASTM B972-10 预用作电子设备的镀镍织带和缎带扁平铜线标准规范

1.1 This specification covers nickel-coated copper braid and ribbon flat wire intended for electronic application (Explanatory Note 1). 1.2 Two classes of nickel-coated braid and ribbon flat copper wire are covered as follows: 1.2.1 Class A– Annealed temper. 1.2.2 Class H– Hard-drawn. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3.1 Exceptions8212;The SI values for density, resistivity, and volume are to be regarded as standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Nickel-Coated Braid and Ribbon Flat Copper Wire Intended for use in Electronic Application

ASTM B973-10 预用作电子设备的镀锡织带和缎带扁平铜线标准规范

1.1 This specification covers tin-coated hard-drawn copper braid and ribbon flat wire intended for electronic application (Explanatory Note 1). 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.2.1 Exceptions8212;The SI values for density, resistivity, and volume are to be regarded as standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Tin-Coated Braid and Ribbon Flat Copper Wire intended for use in Electronic Application

ASTM B802/B802M-10(2016) 钢心铝绞线(ACSR)用Zn-5%铝稀土合金镀层钢芯线标准规格

1.1 This specification covers round, zinc–58201;% aluminum-mischmetal (Zn–5Al–MM) alloy-coated, steel core wire with three classes of Zn–5Al–MM coating used for mechanical reinforcement in the manufacture of aluminum conductors, steel reinforced (ACSR). 1.2 This specification covers wire of diameter from 0.0500 to 0.1900 in. or 1.27 to 4.82 mm, inclusive. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

Standard Specification for Zinc&x2013;5&x2009;% Aluminum-Mischmetal Alloy-Coated Steel Core Wire for Aluminum Conductors, Steel Reinforced (ACSR)

IEC 60317-18:2004/AMD1:2009 特定类型绕组线规范.第18部分:200级聚乙烯醇缩醛漆包矩形铜线.修改件1

Specifications for particular types of winding wires - Part 18: Polyvinyl acetal enamelled rectangular copper wire, class 120; Amentment 1