K20 旋转电机综合 标准查询与下载

JB/T 8982-2011 三相交流稳频稳压电源机组及系统技术条件

本标准规定了三相交流稳频稳压电源机组及系统的基本参数、技术要求、试验方法、检验规则以及标志、包装等。 本标准适用于电动机拖动的同步发电机组及其稳频稳压装置的整套系统（以下简称系统）。电源系统作为小型三相交流电机及其他电器试验用的低波动率、宽调节范围的电源设备，也可作为符合本标准技术指标的其他用电器的电源设备，或作为变频电源设备。

Specification for a.c.three-phase stable frequency and voltage power source set and system

KS B ISO 14695:2011 工业风机.风机振动的测量方法

이 표준은 천장 환풍기나 선풍기와 같이 단지 공기 순환용으로만 설계된 송풍기를 제외한 모든

Industrial fans-Method of measurement of fan vibration

IEC 2/1651/CD:2011 IEC/TS 60034-27-3,版本1:旋转电机.第27-3部分:在旋转电机定子绕组绝缘上的电介质损耗因数测量

IEC/TS 60034-27-3, Ed. 1: Rotating electrical machines - Part 27-3: Dielectric dissipation factor measurement on stator winding insulation of rotating electrical machines

NF C51-316-1*NF EN 60034-16-1:2011 旋转电机.第16-1部分:同步机用激励系统.定义

Rotating electrical machines - Part 16-1 : excitation systems for synchronous machines - Definitions.

IEC 61800-3:2004/AMD1:2011 可调速电力驱动系统.第3部分:EMC要求和特殊试验法

Adjustable speed electrical power drive systems - Part 3: EMC requirements and specific test methods

UL 1004-4-2011 发电机

Electric generators

NF C51-318-32*NF EN 60034-18-32:2011 旋转电机.第18-32部分:绝缘系统的功能评估.模绕式绕组测试规程.通过电气耐久性进行评估.

Rotating electrical machines - Part 18-32 : functional evaluation of insulation systems - Test procedures for form-wound windings - Evaluation by electrical endurance.

DIN EN 60034-16-1:2011 旋转电机.第16-1部分:同步电机的励磁系统.定义(IEC 60034-16-1-2011);德文版本EN 60034-16-1-2011

Rotating electrical machines - Part 16-1: Excitation systems for synchronous machines - Definitions (IEC 60034-16-1:2011); German version EN 60034-16-1:2011

DIN CLC/TS 60034-27:2011 旋转电机.第27部分:在旋转电机绝缘子绕组上的局部离线放电测量(IEC/TS 60034-27-2006);德文版本CLC/TS 60034-27-2011

Rotating electrical machines - Part 27: Off-line partial discharge measurements on the stator winding insulation of rotating electrical machines (IEC/TS 60034-27:2006); German version CLC/TS 60034-27:2011

BS DD CLC/TS 60034-27:2011 旋转电机.旋转电机定子绕组绝缘体的脱线局部放电测量

Rotating electrical machines. Off-line partial discharge measurements on the stator winding insulation of rotating electrical machines

DIN CLC/TS 60034-31:2011 旋转电机.第31部分:包含变速马达设备的节能电机的选择.应用指南(IEC/TS 60034-31-2010).德文版本CLC/TS 60034-31-2011

Rotating electrical machines - Part 31: Selection of energy-efficient motors including variable speed applications - Application guide (IEC/TS 60034-31:2010); German version CLC/TS 60034-31:2011

BS DD CLC/TS 60034-24:2011 旋转电机.在线检测诊断旋转电机和承载电流的有源部件的潜在缺陷.应用指南

This part of IEC 60034 is applicable to the on-line detection and diagnosis of failures at the active parts of multi-phase rotating electrical machines (induction and synchronous machines) and of bearing currents. The failure analysis includes: – interturn faults; – phase-to-phase short-circuits; – double earth faults and single earth faults of motors with earth connection of the star-point; – static and dynamic eccentricities; – cage imperfection or defects (e.g. broken bars or end-rings); – bearing currents. This can be achieved by tools like search coils or other magnetic sensors or partly by the analysis of the terminal voltages and currents. The detection of the following effects is excluded from the scope: – vibration (covered by ISO standards, e.g. ISO 10816 and ISO 7919); – partial discharge (covered by IEC 60034-27); – single earth-faults of motors without earth connection of the star-point; – core imperfection. Also excluded are special methods applicable for specific applications only (e.g. turbo generators).

Rotating electrical machines. Online detection and diagnosis of potential failures at the active parts of rotating electrical machines and of bearing currents. Application guide

BS DD CLC/TS 60034-18-33:2011 旋转电机.绝缘系统的功能评价.模绕组用试验规程.耐同步热应力和电应力的多因素评价

This part of IEC 60034-18 describes procedures for evaluation of insulation systems by endurance testing where thermal and electrical stresses are applied simultaneously. The procedures are intended for insulation systems used, or proposed to be used, in a.c. electrical machines using form-wound windings. The test procedures provide a comparison of performance between reference and candidate systems at combinations of voltage and temperature which have been used separately to assess quality in the past and which are chosen to produce failures within a suitable timescale and at stresses within practical limits. The outcome of the test on the candidate insulation system will indicate whether it is better or worse than the reference system with proven service experience but will not enable a lifetime in service to be calculated. The evaluation described in this technical specification does not include stress grading. The test procedures in this technical specification are not intended to establish the interaction between thermal and electrical stress in the ageing process nor endurance lines. If additional information is required on this interaction or in order to achieve endurance lines, it is necessary to undertake further tests in which electrical ageing is carried out at constant temperature and different voltages (IEC 60034-18-32) and thermal ageing is performed at different temperatures and constant voltage.

Rotating electrical machines. Functional evaluation of insulation systems. Test procedures for form-wound windings. Multifactor evaluation by endurance under simultaneous thermal and electrical stresses

BS DD CLC/TS 60034-31:2011 旋转电机.包含变速马达设备的节能电机的选择.应用指南

This part of IEC 60034 provides a guideline of technical aspects for the application of energyefficient, three-phase, electric motors. It not only applies to motor manufacturers, OEMs (original equipment manufacturers), end users, regulators and legislators but to all other interested parties. This technical specification is applicable to all electrical machines covered by IEC 60034-30. Most of the information however is also relevant for cage-induction machines with output powers exceeding 375 kW.

Rotating electrical machines. Selection of energy-efficient motors including variable speed applications. Application guide

DL/T 294.1-2011 发电机灭磁及转子过电压保护装置技术条件 第1部分：磁场断路器

本标准规定了大中型同步发电机灭磁及转子过电压保护装置中的磁场断路器使用的术语和定义、基本技术要求、试验方法、检验规则、技术文件、包装、运输和贮存等规定。 本标准适用于单机容量为10MW及以上发电机灭磁及转子过电压保护装置的磁场断路器使用与订货要求。

Specification for equipment of de-excitation and over voltage protection for generators. Part 1:Field circuit breaker

DL/T 298-2011 发电机定子绕组端部电晕检测与评定导则

本标准规定了使用日盲型紫外成像装置和暗室目测法对发电机定子绕组端部进行电晕检测的方法和评定的标准。 本标准适用于定子额定电压在10.5KV及以上的发电机。 其他旋转电机也可参照执行。

Guide for detection and evaluation of corona defects on stator winding overhangs of generator

DL/T 294.2-2011 发电机灭磁及转子过电压保护装置技术条件 第2部分：非线性电阻

本标准规定了同步发电机灭磁及转子过电压保护装置用非线性电阻的基本技术要求、使用的术语、定义、计算方法、试验、技术文件等。 本标准适用于单片标称容量为10kJ及以上的非线性电阻阀片及组件，应用于发电机灭磁及转子过电压保护装置非线性电阻的使用与订货要求。

Specification for equipment of de-excitation and over voltage protection for generators. Part 2:Non-linear resistor

DIN CLC/TS 60034-18-42:2011 旋转电机.第18-42部分:电压转换器馈电的旋转电机用抗局部放电电气绝缘系统(II型)的鉴定和验收试验(IEC/TS 60034-18-42-2008).德文版本CLC/TS 60034-18-42-2011

Rotating electrical machines - Part 18-42: Qualification and acceptance tests for partial discharge resistant electrical insulation systems (Type II) used in rotating electrical machines fed from voltage converters (IEC/TS 60034-18-42:2008); German versio

DIN CLC/TS 60034-18-33:2011 旋转电机.第18-33部分:绝缘系统的功能评价.模绕组用试验规程.耐同步热应力和电应力的多因素评价(IEC/TS 60034-18-33-2010).德文版本CLC/TS 60034-18-33-2011

Rotating electrical machines - Part 18-33: Functional evaluation of insulation systems - Test procedures for form-wound windings - Multifactor evaluation by endurance under simultaneous thermal and electrical stresses (IEC/TS 60034-18-33:2010); German ver

DIN CLC/TS 60034-24:2011 旋转电机.第24部分:在线探测和诊断旋转电机和轴承电流的有源部件的潜在缺陷.应用指南(IEC/TS 60034-24-2009).德文版本CLC/TS 60034-24-2011

Rotating electrical machines - Part 24: Online detection and diagnosis of potential failures at the active parts of rotating electrical machines and of bearing currents - Application guide (IEC/TS 60034-24:2009); German version CLC/TS 60034-24:2011