共找到 1061 条与 旋转电机综合 相关的标准,共 71 页
Guide for the Application of Electric Motors in Class I, Division 2 and Class I, Zone 2 Hazardous (Classified) Locations
Assists users in the proper selection and application of motors and generators. Practical information concerning performance, safety, test, construction and manufacture of ac and dc motors and generators.
Motors and Generators
Electric traction. Rotating electrical machines for rail and road vehicles. Machines other than electronic converter-fed alternating current motors
이 표준은 분산된 형태의 지역 전력 공급 시스템에서 각 발전기(최대 출력=100 kVA)의
Recommendations for small renewable energy and hybrid systems for rural electrification-Part 7:Generators
이 표준은 분산 배치된 지역 전력 공급 시스템에서 발전기 세트의 선정, 크기 결정, 시공
Recommendations for small renewable energy and hybrid systems for rural electrification-Part 7-3:Generator set-Selection of generator sets for rural electrification systems
This part of IEC 60034 is applicable to all rotating electrical machines except those covered by other IEC standards, for example, IEC 60349 [10]1). Machines within the scope of this standard may also be subject to superseding, modifying or additional requirements in other publications, for example, IEC 60079 [8] and IEC 60092 [9]. NOTE If particular clauses of this standard are modified to meet special applications, for example machines subject to radioactivity or machines for aerospace, all other clauses apply insofar as they are compatible.
Rotating electrical machines. Rating and performance
本部分规定了对各类进出口机电产品的检验风险进行分析和评定的原则和程序。 本部分适用于对进出口机电产品检验的风险评价,为相关风险管理活动提供信息和依据。
General requirements of inspection on electrical and mechanical products for import and export.Part 2:Risk assessment
IEC/TS 60034-27-2, Ed. 1: Rotating electrical machines - Part 27-2: On-line partial discharge measurements on the stator winding insulation of rotating electrical machines
Rotating electrical machines - Part 2-2: Specific methods for determining separate losses of large machines from tests - Supplement to IEC 60034-2-1 (IEC 60034-2-2:2010); German version EN 60034-2-2:2010
This part of IEC 60034-18 describes test procedures for the evaluation of electrical endurance of insulation systems for use in a.c. or d.c. rotating electrical machines using form-wound windings. The test procedures are comparative in nature, such that the performance of a candidate insulation system is compared to that of a reference insulation system with proven service experience. The test procedures are principally directed at the insulation systems in air-cooled machines but may also be used for evaluating parts of the insulation systems in hydrogen cooled machines. Note that the qualification procedures of inverter duty insulation systems for form-wound windings can be found in IEC 60034-18-42.
Rotating electrical machines - Part 18-32: Functional evaluation of insulation systems - Test procedures for form-wound windings - Evaluation by electrical endurance
Rotating electrical machines - Part 18-1: Functional evaluation of insulation systems - General guidelines (IEC 60034-18-1:2010); German version EN 60034-18-1:2010
Household and similar electrical appliances - Safety - Part 2-34 : particular requirements for motor-compressors.
Adjustable speed electrical power drive systems - Specification of voltage on the power interface
This part of IEC 60034 applies to large rotating electrical machines and establishes additional methods of determining separate losses and to define an efficiency supplementing IEC 60034-2-1. These methods apply when full-load testing is not practical and result in a greater uncertainty. The specific methods described are: – Calibrated-machine method. – Retardation method. – Calorimetric method.
Rotating electrical machines - Specific methods for determining separate losses of large machines from tests - Supplement to IEC 60034-2-1
This part of IEC 60034-18 describes procedures for evaluation of insulation systems by endurance testing where thermal and electrical stresses are applied simultaneously. The procedures are intended for insulation systems used, or proposed to be used, in a.c. electrical machines using form-wound windings. The test procedures provide a comparison of performance between reference and candidate systems at combinations of voltage and temperature which have been used separately to assess quality in the past and which are chosen to produce failures within a suitable timescale and at stresses within practical limits. The outcome of the test on the candidate insulation system will indicate whether it is better or worse than the reference system with proven service experience but will not enable a lifetime in service to be calculated. The evaluation described in this technical specification does not include stress grading. The test procedures in this technical specification are not intended to establish the interaction between thermal and electrical stress in the ageing process nor endurance lines. If additional information is required on this interaction or in order to achieve endurance lines, it is necessary to undertake further tests in which electrical ageing is carried out at constant temperature and different voltages (IEC 60034-18-32) and thermal ageing is performed at different temperatures and constant voltage.
Rotating electrical machines - Part 18-33: Functional evaluation of insulation systems - Test procedures for form-wound windings - Multifactor evaluation by endurance under simultaneous thermal and electrical stresses
This part of IEC 60034 deals with the general guidelines for functional evaluation of electrical insulation systems, used or proposed to be used in rotating electrical machines within the scope of IEC 60034-1, in order to qualify them.
Rotating electrical machines - Functional evaluation of insulation systems - General guidelines
Rotating electrical machines - Part 22 : AC generators for reciprocating internal combustion (RIC) engine driven generating sets.
Arrangement of terminals for rotating electrical machines - Part 2: Rated voltage 11 kV
Arrangement of terminals for rotating electrical machines - Part 1: Rated voltage 6,6 kV
IEC 60034의 이 부분은 IM 코드,구조의 형식 분류와 회전 전기기기의 설치 배열을
Rotating electrical machines-Part 7:Classification of types of construction, mounting arrangements and terminal box position(IM Code)
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号