K20 旋转电机综合 标准查询与下载

ANSI/IEEE 1068:2009 石油、化学和加工行业用交流电动机的维修和冲绕标准

This standard is intended to be a basic or primary document that can be utilized and referenced by owners of AC motors and generators (machines) that need refurbishment, repair, and/or rewinding, as well as service or repair facilities. It has been developed for the Petroleum, Chemical and Process industries, and may be adapted to other areas of interest.

Standard for the Repair and Rewinding of AC Electric Motors in the Petroleum, Chemical and Process Industries

ANSI/IEEE 433:2009 高压超低频交流电力机械绝缘试验的推荐实施规程

This document describes very low frequency (VLF) testing of ac electric machines. It covers acceptance testing of new machines in the factory or on-site after erection. Also covered is the routine maintenance testing of machines that have been in service. In order to facilitate communication and comparison among investigators, this document recommends that the very low frequency used be 0.1 Hz +/- 10 percent.

Recommended Practice for Insulation Testing of AC Electric Machinery with High Voltage at Very Low Frequency

ANSI/UL 1004-8-2009 变频器专用电动机的安全标准

UL proposes the first edition of UL 1004-8, Inverter Duty Motors.

Standard for Safety for Inverter Duty Motors

IEEE 841-2009 石油和化学工业用标准.最高达370kW(500hp)的全封闭风扇冷却式鼠笼式感应电动机

This standard applies to premium-efficiency totally enclosed fan-cooled (TEFC), horizontal and vertical, single-speed, squirrel cage polyphase induction motors, up to and including 370 kW (500 hp), and 4000 V nominal, in National Electrical Manufacturers Association (NEMA) frame sizes 143T and larger, for petroleum, chemical, and other severe-duty applications (commonly referred to as premium-efficiency severe-duty motors). Excluded from the scope of this standard are motors with sleeve bearings and additional specific features required for explosion-proof motors.

Standard for petroleum and chemical industry - Premium-efficiency, severe-duty, Totally Enclosed Fan-Cooled (TEFC) squirrel cage induction motors - Up to and including 370 kW (500 hp)

JIS C 4421:2008 可调速的电驱动系统(PDS).电磁兼容性(EMC)要求和专用试验方法

Adjustable speed electrical power drive systems (PDS) -- Electromagnetic compatibility (EMC) requirements and specific test methods

IEC 2/1537/DTS:2008 IEC/TS 60034-24:旋转电机.第24部分:旋转电机和轴承电流有源部件的电位故障在线探测和诊断.应用指南

IEC/TS 60034-24: Rotating electrical machines - Part 24: Online detection and diagnosis of potential failures at the active parts of rotating electrical machines and of bearing currents - Application guide

KS C IEC 60034-11:2008 旋转电机.第11部分:内装式热保护

이 표준은 열적 과부하로 인한 심각한 손상을 방지하기 위하여 고정자 권선에 내장되거나, 다

Rotating electrical machines-Part 11:Thermal protection

KS C IEC 60034-1:2008 旋转电机.第1部分:额定值和性能.

이 표준은 다른 KS C IEC 표준, 예를 들어 KS C IEC 60349에 포함된 것을

Rotating electrical machines-Part 1:Rating and performance

KS C IEC 60034-8:2008 旋转电机.第8部分:旋转电机的线端标志和旋转方向

이 표준은 교류 및 직류 기기에 적용되며 다음 사항들을 규정한다.a) 권선 접속점의

Rotating electrical machines－Part 8：Terminal markings and direction of rotation

KS C IEC 60034-12:2008 旋转电机.第12部分:单速三相笼型感应电动机的起动性能

이 표준은 KSC IEC 60034-1에 따라, 4가지 설계 형태에 따른, 다음과 같은 단

Rotating electrical machines－Part 12：Starting performance of single-speed three-phase cage induction motors for voltages up to and including 660 V

KS C IEC 60034-2-1:2008 旋转电机.第2部分:旋转电机损耗和效率的试验测定方法(不包括牵引车辆用电机)

이 표준은 KS C IEC 60034-1의 적용범위 내의 모든 크기의 직류기, 교류 동기기

Rotating electrical machines－Part 2-1：Standard methods for determining losses and efficiency from tests (excluding machines for traction vehicles)

KS C IEC 60034-5:2008 旋转电机.第5部分:旋转电机总体设计的防护等级(IP代码).分级

이 표준은 보호 외함이 따라야 할 요구사항을 정의한다. 이 표준은 다른 모든 점에서 그 목

Rotating electrical machines－Part 5：Degrees of protection provided by the integral design of rotating electrical machines(IP code)－Classification

KS C IEC 60034-14:2008 旋转电机.第14部分:轴中心高56mm及以上电机的可靠机械振动强度的测量、评估和极限值

이 표준은 부하나 원동기를 연결하지 않은 지정된 조건하에서 임의의 전기 기기를 위한 진동

Rotating electrical machines－Part 14：Mechanical vibration of certain machines with shaft heights 56 mm and higher－Measurement, evaluation and limits of vibration severity

KS C IEC 60034-3:2008 旋转电机.第3部分:圆筒形转子同步电机的特殊需求

이 표준은 정격 출력이 10 MVA 이상 출력과 스팀 터빈 혹은 산화 가스 터빈을 가지는

Rotating electrical machines－Part 3：Specific requirements for synchronous generators driven by steam turbines or combustion gas turbines

SANS 61800-7-201:2008 可调速电力驱动系统.第7-201部分:电驱动设备轮廓的通用接口和使用.1型轮廓规范

Specifies profile type 1 for Power Drive Systems, which can be mapped onto different communication network technologies.

Adjustable speed electrical power drive systems Part 7-201: Generic interface and use of profiles for power drive systems - Profile type 1 specification

SANS 61800-7-302:2008 可调速电力驱动系统.第7-302部分:电驱动设备轮廓的通用接口和使用.2型轮廓映射到网络的技术

Specifies the mapping of profile type 2 onto different network technologies by use of a generic interface model.

Adjustable speed electrical power drive systems Part 7-302: Generic interface and use of profiles for power drive systems - Mapping of profile type 2 to network technologies

SANS 61800-7-303:2008 可调速电力驱动系统.第7-303部分:电驱动设备轮廓的通用接口和使用.3型轮廓映射到网络的技术

Specifies the mapping of profile type 3 onto different network technologies by use of a generic interface model.

Adjustable speed electrical power drive systems Part 7-303: Generic interface and use of profiles for power drive systems - Mapping of profile type 3 to network technologies

SANS 61800-7-204:2008 可调速电力驱动系统.第7-204部分:电驱动设备轮廓的通用接口和使用.4型轮廓规范

Specifies profile type 4 for Power Drive Systems, which can be mapped onto different communication network technologies.

Adjustable speed electrical power drive systems Part 7-204: Generic interface and use of profiles for power drive systems - Profile type 4 specification

SANS 61800-7-301:2008 可调速电力驱动系统.第7-301部分:电驱动设备轮廓的通用接口和使用.1型轮廓映射到网络的技术

Specifies the mapping of profile type 1 onto different network technologies by use of a generic interface model.

Adjustable speed electrical power drive systems Part 7-301: Generic interface and use of profiles for power drive systems - Mapping of profile type 1 to network technologies

SANS 61800-7-1:2008 可调速电力驱动系统.第7-1部分:电驱动设备轮廓的通用接口和使用.接口定义

Specifies a generic interface between Power Drive System(s) (PDS) and the application control program in a controller. The generic PDS interface is not specific to any particular communication network technology.

Adjustable speed electrical power drive systems Part 7-1: Generic interface and use of profiles for power drive systems - Interface definition