K20 旋转电机综合 标准查询与下载

SANS 61800-7-204:2008 可调速电力驱动系统.第7-204部分:电驱动设备轮廓的通用接口和使用.4型轮廓规范

Specifies profile type 4 for Power Drive Systems, which can be mapped onto different communication network technologies.

Adjustable speed electrical power drive systems Part 7-204: Generic interface and use of profiles for power drive systems - Profile type 4 specification

SANS 61800-7-202:2008 可调速电力驱动系统.第7-202部分:电驱动设备轮廓的通用接口和使用.2型轮廓规范

Specifies profile type 2 for Power Drive Systems, which can be mapped onto different communication network technologies.

Adjustable speed electrical power drive systems Part 7-202: Generic interface and use of profiles for power drive systems - Profile type 2 specification

SANS 61800-7-301:2008 可调速电力驱动系统.第7-301部分:电驱动设备轮廓的通用接口和使用.1型轮廓映射到网络的技术

Specifies the mapping of profile type 1 onto different network technologies by use of a generic interface model.

Adjustable speed electrical power drive systems Part 7-301: Generic interface and use of profiles for power drive systems - Mapping of profile type 1 to network technologies

NF C51-114:2008 旋转电机.第4部分:根据试验测定同步机数值的方法

Rotating electrical machines - Part 4 : methods for determining synchronous machine quantities from tests.

IEC 2/1530/CD:2008 IEC/TS 60034-18-33，编 2：旋转电机 第 18-33 部分：绝缘系统的功能评估 通过在同时热应力和电应力下耐久性对成型绕组进行多功能评估的测试程序

IEC/TS 60034-18-33, Ed. 2: Rotating electrical machines - Part 18-33: Functional evaluation of insulation systems - Test procedures for multifunctional evaluation of form-wound windings by endurance under simultaneous thermal and electrical stresses of in

IEC 60034-30:2008 旋转电机.第30部分:单速三相鼠笼式感应电动机的有效等级(IE编码)

This part of IEC 60034 specifies efficiency classes for single-speed, three-phase, 50 Hz and 60 Hz, cage-induction motors that: ~ have a rated voltage UN up to 1 000 V; NOTE The standard also applies to motors rated for two or more voltages and/or frequencies. ~ have a rated output PN between 0,75 kW and 375 kW; ~ have either 2, 4 or 6 poles; ~ are rated on the basis of either duty type $1 (continuous duty) or $3 (intermittent periodic duty) with a rated cyclic duration factor of 80 % or higher; ~ are capable of operating direct on-line; ~ are rated for operating conditions in accordance with IEC 60034-1, Clause 6. Motors with flanges, feet and/or shafts with mechanical dimensions different from IEC 60072-1 are covered by this standard. Geared motors and brake motors are covered by this standard although special shafts and flanges may be used in such motors. Excluded are: ~ Motors made solely for converter operation in accordance with IEC 60034-25. ~ Motors completely integrated into a machine (for example pump, fan and compressor) that cannot be tested separately from the machine.

Rotating electrical machines - Part 30: Efficiency classes of single-speed, three-phase, cage induction motors (IE code)

BS EN 61800-7-1:2008 可调速电力传动系统.通用接口和电力驱动系统断面的使用.接口定义

IEC 61800-7 specifies profiles for power drive systems (PDS) and their mapping to existing communication systems by use of a generic interface model. The functions specified in this part of IEC 61800-7 are not intended to ensure functional safety. This requires additional measures according to the relevant standards, agreements and laws. This part of IEC 61800-7 specifies a generic interface between power drive system(s) (PDS) and the application control program in a controller. The generic PDS interface is not specific to any particular communication network technology. Annexes of this part of IEC 61800-7 specify the mapping of the different drive profiles types onto the generic PDS interface.

Adjustable speed electrical power drive systems - Generic interface and use of profiles for power drive systems - Interface definition

BS EN 61800-7-304:2008 可调速电驱动系统.电力传动系统用剖面图的使用和通用接口.4型剖面图映射到网络技术

IEC 61800-7 specifies profiles for Power Drive Systems (PDS) and their mapping to existing communication systems by use of a generic interface model. The functions specified in this part of IEC 61800-7 are not intended to ensure functional safety. This requires additional measures according to the relevant standards, agreements and laws. This part of IEC 61800-7 specifies the mapping of the profile type 4 (SERCOS) specified in IEC 61800-7-204 onto different network technologies. – SERCOS I / II, see Clause 5, – SERCOS III, see Clause 6, – EtherCAT, see Clause 7.

Adjustable speed electrical power drive systems - Generic interface and use of profiles for power drive systems - Mapping of profile type 4 to network technologies

BS EN 60034-29:2008 旋转电机.等效加载和迭加技术.测定温升的间接试验

This International Standard applies to machines covered by IEC 60034-1 when they cannot be loaded to a specific condition (rated or otherwise). It is applicable to both motors and generators.

Rotating electrical machines. Equivalent loading and superposition techniques. Indirect testing to determine temperature rise

UL 1004-3-2008 热防护型电动机

Thermally protected motors

UL 1004-2-2008 阻抗防护型电动机

Impedance protected motors

IEC TS 60034-18-42:2008 旋转电机.第18-42部分:电压转换器馈电的旋转电机用抗局部放电电气绝缘系统(II型)的鉴定和验收试验

This Technical Specification defines criteria for assessing the insulation system of stator/rotor windings of single or polyphase AC machines which are subjected to repetitive impulse voltages, such as pulse width modulation (PWM) converters, and expected to withstand partial discharge activity during service. It specifies electrical qualification and acceptance tests on representative samples which verify fitness for operation with voltage-source converters. This document does not apply to: - Rotating machines which are fed by converters only for starting. - Electrical equipment and systems for traction. NOTE Although this Technical Specification deals with voltage-source converters, it is recognised that there are other types of converters that can create repetitive impulse voltages. For these converters, a similar approach to testing can be used if needed.

Rotating electrical machines - Part 18-42: Qualification and acceptance tests for partial discharge resistant electrical insulation systems (Type II) used in rotating electrical machines fed from voltage converters

DIN EN 60034-2-1:2008 旋转电机.第2-1部分:通过试验测定旋转电机损耗和效率的标准方法(不包括牵引车辆用电机)

Rotating electrical machines - Part 2-1: Standard methods for determining losses and efficiency from tests (excluding machines for traction vehicles) (IEC 60034-2-1:2007); German version EN 60034-2-1:2007

JEM 1420-2008 额定输出电压大于3kVA和小于10kVA的便携式发动机驱动的交流发电装置

Portable type engine driven a.c.generating sets for rated output above 3 kVA and less than 10 kVA

SANS 61800-5-2:2008 可调速电力驱动系统.第5-2部分:安全要求.功能

Specifies requirements and makes recommendations for the design and development, integration and validation of safety-related power-drive-systems [PDS(SR)s] in terms of their functional safety considerations. Applies to adjustable speed electric drive sy

Adjustable speed electrical power drive systems Part 5-2: Safety requirements - Functional

BS EN 61800-7-203:2008 可调速电驱动设备.电驱动设备轮廓的通用接口和使用.3型轮廓规范

IEC 61800-7 specifies profiles for Power Drive Systems (PDS) and their mapping to existing communication systems by use of a generic interface model. The functions specified in this part of IEC 61800-7 are not intended to ensure functional safety. This requires additional measures according to the relevant standards, agreements and laws. This part of IEC 61800-7 specifies profile type 3 for Power Drive Systems (PDS). Profile type 3 can be mapped onto different communication network technologies.

Adjustable speed electrical power drive systems - Part 7-203: Generic interface and use of profiles for power drive systems — Profile type 3 specification

BS EN 61800-7-201:2008 可调速电驱动设备.电驱动设备轮廓的一般接口和使用.1型轮廓规范

IEC 61800-7 specifies profiles for Power Drive Systems (PDS) and their mapping to existing communication systems by use of a generic interface model. The functions specified in this part of IEC 61800-7 are not intended to ensure functional safety. This requires additional measures according to the relevant standards, agreements and laws. This part of IEC 61800-7 specifies profile type 1 for Power Drive Systems (PDS). Profile type 1 can be mapped onto different communication network technologies.

Adjustable speed electrical power drive systems - Part 7-201: Generic interface and use of profiles for power drive systems — Profile type 1 specification

BS EN 61800-7-202:2008 可调速电驱动设备.电驱动设备轮廓的一般接口和使用.2型轮廓规范

IEC 61800-7 specifies profiles for Power Drive Systems (PDS) and their mapping to existing communication systems by use of a generic interface model. The functions specified in this part of IEC 61800-7 are not intended to ensure functional safety. This requires additional measures according to the relevant standards, agreements and laws. This part of IEC 61800-7 specifies profile type 2 (CIP Motion™) for Power Drive Systems (PDS). Profile type 2 can be mapped onto different communication network technologies.

Adjustable speed electrical power drive systems - Part 7-202: Generic interface and use of profiles for power drive systems — Profile type 2 specification

SANS 60034-29:2008 旋转电机.第29部分:等效负载及叠加技术-间接检测以确定温升

Applies to machines covered by IEC 60034-1 (published in South Africa as an identical adoption under the designation SANS 60034-1) when they cannot be loaded to a specific condition (rated or otherwise). Is applicable to both motors and generators.

Rotating electrical machines Part 29: Equivalent loading and superposition techniques - Indirect testing to determine temperature rise

JIS C 2820:2008 电机用电刷材料的物理性能测定用试验程序

This Standard specifies test procedures for determining the physical prop- erties of brush materials for electrical machines, i.e. bulk density, hardness, resistiv- ity, transverse strength and for determining the ash content. NOTES 1 The properties determined by these tests are inherent in the brush materials themselves as distinct from performance characteristics in operation on electrical equipment. It should be kept in mind that since brush materials are generally brittle, porous materials, it is reasonable that their properties vary much more than the same properties in metals. Samples used for these tests shall be representative of the batch of material involved using a recognized and/or agreed sampling procedure or technique. 2 The International Standard corresponding to this Standard is as follows. The symbols which denote the degree of correspondence between JIS and the corresponding International Standard are IDT (identical), MOD (modified), and NEQ (not equivalent) according to ISO/IEC Guide 21. IEC 60413 : 1972 Test procedures for determining physical properties of brush materials for electrical machines (MOD)

Test procedures for determining physical properties of brush materials for electrical machines