K20 旋转电机综合 标准查询与下载

JB/T 2728.5-2008 电机用气体冷却器.第5部分:绕簧式气体冷却器技术要求

JB/T 2728的本部分规定了电机用绕簧式气体冷却器的技术要求。 本部分适用于各类电机用的绕簧式气体冷却器。

Gas cooler for electrical machinery.Part5:Specification for winded-spiral-wire type gas cooler

JB/T 2728.4-2008 电机用气体冷却器.第4部分:绕片式气体冷却器技术要求

JB/T 2728的本部分规定了电机用绕片式气体冷却器的技术要求。 本部分适用于各类电机用的绕片式气体冷却器。

Gas cooler for electrical machinery.Part4:Specification for winded-fin type gas cooler

JB/T 8439-2008 使用于高海拔地区的高压交流电机防电晕技术要求

本标准规定了使用于高海拔地区的高压交流电机防电晕技术、试验方法及检验规则。 本标准适用于工作海拔1000m以上至5000m、额定电压6kV及以上的绕组和铁心与环境大气相接处的交流电机。 有防电晕要求的其他交流电机亦可参照使用。

Corona-proof specification of high voltage rotating a.c machines used in high altitude area

JB/T 2728.2-2008 电机用气体冷却器.第2部分:穿片式气体冷却器技术要求

JB/T 2728的本部分规定了电机用穿片式气体冷却器的技术要求。 本部分适用于各类电机用的穿片式气体冷却器。

Gas cooler for electrical machinery.Part2:Specification for bunched-fin type gas cooler

JB/T 2728.1-2008 电机用气体冷却器.第1部分:一般规定

JB/T 2728的本部分规定了电机用气体冷却器的通用技术条件。 本部分适用于各类电机用常规型式的气体冷却器。

Gas cooler for electrical machinery.Part1:General rules

JB/T 2728.3-2008 电机用气体冷却器.第3部分:挤片式气体冷却器技术要求

JB/T 2728的本部分规定了电机用挤片式气体冷却器的技术要求。 本部分适用于分类电机用的挤片式气体冷却器。

Gas cooler for electrical machinery.Part3:Specification for extruded-fin type gas cooler

JB/T 10922-2008 高原铁路机车用旋转电机技术要求

本标准规定了高原铁路机车用旋转电机的要求、试验、标志、包装、运输与贮存。 本标准适用于海拔为1000m以上5100以下环境条件下的铁路机车用旋转电机，其他在高海拔地区使用的旋转电机也可参照使用。 本标准不适用于电力电子变流器供电的交流电动机和测速发电机。

Technical specification of rotating electrical machines used on plateau locamative

NF C51-112:2008 旋转电机.第2-1部分:试验(不包括牵引车辆用电机)中损失和功效的测定用标准方法

Rotating electrical machines - Part 2-1 : standard methods for determining losses and efficiency from tests (excluding machines for traction vehicles).

IEC 2/1513/CD:2008 IEC/TS 60034-18-33:旋转电机.第18-33部分:绝缘系统的功能评估.通过旋转电机用绝缘系统的电应力模绕组线和热同时作用下的耐久性评估多功能性用试验程序

IEC/TS 60034-18-33: Rotating electrical machines - Part 18-33: Functional evaluation of insulation systems - Test procedures for multifunctional evaluation of form-wound windings by endurance under simultaneous thermal and electrical stresses of insulatio

IEC 2/1507/CD:2008 IEC/TS 60034-18-32:旋转电机.第18-32部分:绝缘系统的功能评估.成型绕组的试验程序.旋转电机用绝缘系统的电气评估

IEC/TS 60034-18-32: Rotating electrical machines - Part 18-32: Functional evaluation of insulation systems - Test procedures for form-wound windings - Electrical evaluation of insulation systems used in rotatig electrical machines

BS EN 61800-7-303:2008 可调速电驱动设备.电驱动设备的一般接口和使用.3型轮廓映射到网络技术

IEC 61800-7 specifies profiles for Power Drive Systems (PDS) and their mapping to existing communication systems by use of a generic interface model. The functions specified in this part of IEC 61800-7 are not intended to ensure functional safety. This requires additional measures according to the relevant standards, agreements and laws. This part of IEC 61800 7 specifies how the profile type 3 (PROFIdrive) specified in IEC 61800-7-203 onto different network technologies. – PROFIBUS DP, see Clause 4, – PROFINET IO, see Clause 5.

Part 7-303: Generic interface and use of profiles for power drive systems — Mapping of profile type 3 to network technologies

BS EN 61800-7-301:2008 可调速电驱动设备.电驱动设备的一般接口和使用.1型轮廓映射到网络技术

IEC 61800-7 specifies profiles for Power Drive Systems (PDS) and their mapping to existing communication systems by use of a generic interface model. The functions specified in this part of IEC 61800-7 are not intended to ensure functional safety. This requires additional measures according to the relevant standards, agreements and laws. This part of IEC 61800-7 specifies the mapping of the profile type 1 (CiA 402) specified in IEC 61800-7-201 onto different network technologies. – CANopen, see Clause 5; – EtherCAT, see Clause 6; – ETHERNET Powerlink, see Clause 7.

Adjustable speed electrical power drive systems - Generic interface and use of profiles for power drive systems - Part 7-301: Generic interface and use of profiles for power drive systems — Mapping of profile type 1 to network technologies

BS EN 61800-7-302:2008 可调速电驱动设备.电驱动设备轮廓的一般接口和使用.2型轮廓映射到网络技术

IEC 61800-7 specifies profiles for Power Drive Systems (PDS) and their mapping to existing communication systems by use of a generic interface model. The functions specified in this part of IEC 61800-7 are not intended to ensure functional safety. This requires additional measures according to the relevant standards, agreements and laws. This part of IEC 61800-7 specifies the mapping of the profile type 2 (CIP MotionTM) specified in IEC 61800-7-202 onto different network technologies. – DeviceNet™ (CP 2/3), see Clause 5, – ControlNet™ (CP 2/1), see Clause 6, – EtherNet/IP™ (CP 2/2), see Clause 7.

Adjustable speed electrical power drive systems - Generic interface and use of profiles for power drive systems - Part 7-302: Generic interface and use of profiles for power drive systems — Mapping of profile type 2 to network technologies

IEC 2/1501/CD:2008 IEC/TS 60034-31,Ed.1:旋转电机.第31部分:包括变速设备的能效电动机的选择和应用指南

IEC/TS 60034-31, Ed. 1: Rotating electrical machines - Part 31: Guide for the selection and application of energy-efficient motors including variable-speed applications

IEC 60034-4:2008 旋转电机.第4部分:试验中同步电机参数的测定用方法

This part of IEC 60034 applies to three-phase synchronous machines of 1 kVA rating and larger with rated frequency of not greater than 500 Hz and not less than 10 Hz. Most of the methods are intended to be used for machines having an excitation winding with slip-rings and brushes for their supply. Synchronous machines with brushless excitation require special effort for some of the tests. For machines with permanent magnet excitation, there is a limited applicability of the described tests, and special precautions have to be taken against irreversible demagnetization. Excluded are axial-field machines and special synchronous machines such as inductor type machines and transversal flux machines. It is not intended that this standard be interpreted as requiring any or all of the tests described therein on any given machine. The particular tests to be carried out shall be subject to agreement between manufacturer and customer.

Rotating electrical machines - Part 4: Methods for determining synchronous machine quantities from tests

ANSI/IEEE 1553:2007 水轮发电机用模绕线圈和棒耐电压测试的标准

This standard applies to voltage-endurance testing of form-wound stator winding bars and coils having a mica-based insulation system with thermo-setting polyester and/or epoxy resins used in hydrogenerators and pumped storage generators operating in air with a rated line-to-line voltage between 4 000 to 22 000 V, and a frequency of 50 Hz or 60 Hz.

Standard for Voltage Endurance Testing of Form-Wound Coils and Bars for Hydrogenerators

SANS 1470-3:2008 声功率标识.第3部分:旋转电机

Covers the requirements for the labelling of rotating electrical machinery with a noise emission value and specifies the test method to be used for the verification of the labelled value.

Sound power labelling Part 3: Rotating electrical machinery

UL 2519 BULLETIN-2008 UL 1004-3过热保护型电机UL安全性标准.评议第1版.评议提交截止日期:2008年5月19日

Ul Standard for Safety proposed first edition of UL 1004-3, Thermally Protected motors COMMENTS DUE:MAY 19.20

Ul Standard for Safety proposed first edition of UL 1004-3, Thermally Protected motors COMMENTS DUE:MAY 19.20

UL 2517 BULLETIN-2008 UL 1004-1旋转电机.一般要.评议第1版.评议提交截止日期:2008年5月19日

The proposed first edition of UL 1004-1, Rotating Electrical Machines - General Requirements COMMENTS DUE: MAY 19, 2008

The proposed first edition of UL 1004-1, Rotating Electrical Machines - General Requirements COMMENTS DUE: MAY 19, 2008

UL 1004-4 BULLETIN-2008 UL安全标准.发电机.评议提交截止日期:2008年5月19日

Covers safety requirements for motors, motor parts, and combinations of such parts intended for use in appliances and equipment that comply with the requirments for such appliances and equipment. This standard applies to both open and totally enclosed motors. It covers commutator motors of the series, shunt, compund, and permanent magnet-field types rated 5 horsepower or less, 250 volts or less, alternating current or direct current. It also covers motors other than the aforementioned, rated 600 volts or less, 100 horsepower or less, with 19-inch diameters or less, and commutator motors of the repulsion type only. This standard does not cover motors for use in hazardous locations as defined in ANSI/NFPA 70-1981, National Electrical Code, nor does it include performance requirements that depend upon application in the end use equipment.

UL Standard for Safety Electric Generators COMMENTS DUE: MAY 19, 2008