K20 旋转电机综合 标准查询与下载

UL 1004-3 BULLETIN-2008 过热防护型电动机UL安全性标准.评议提交截止日期:2008年5月19日

Covers safety requirements for motors, motor parts, and combinations of such parts intended for use in appliances and equipment that comply with the requirments for such appliances and equipment. This standard applies to both open and totally enclosed motors. It covers commutator motors of the series, shunt, compund, and permanent magnet-field types rated 5 horsepower or less, 250 volts or less, alternating current or direct current. It also covers motors other than the aforementioned, rated 600 volts or less, 100 horsepower or less, with 19-inch diameters or less, and commutator motors of the repulsion type only. This standard does not cover motors for use in hazardous locations as defined in ANSI/NFPA 70-1981, National Electrical Code, nor does it include performance requirements that depend upon application in the end use equipment.

UL Standard for Safety Thermally Protected Motors COMMENTS DUE: MAY 19, 2008

EN 61800-7-303:2008 可调速的电力传动系统.第7-303部分:通用接口和电力传动系统用剖面图的使用.3型剖面图映射到网络技术

IEC 61800-7 specifies profiles for Power Drive Systems (PDS) and their mapping to existing communication systems by use of a generic interface model. The functions specified in this part of IEC 61800-7 are not intended to ensure functional safety. This requires additional measures according to the relevant standards, agreements and laws. This part of IEC 61800 7 specifies how the profile type 3 (PROFIdrive) specified in IEC 61800-7-203 onto different network technologies. – PROFIBUS DP, see Clause 4, – PROFINET IO, see Clause 5.

Adjustable speed electrical power drive systems - Part 7-303: Generic interface and use of profiles for power drive systems - Mapping of profile type 3 to network technologies (Remains Current)

IEC TS 62257-7-3:2008 农村电气化用小型可再生能源和混合系统的建议.第7-3部分:发电装置.农村电气化系统用发电装置的选择

The purpose of this part of IEC 62257 is to specify the general requirements for the selection, sizing, erection and operation of generator sets in decentralized rural electrification systems. It applies to all low voltage combustion engine electricity generator sets with a rated power up to 100 kVA, and designed for supplying electrical power to isolated sites used in systems as described in IEC/TS 62257-2. This technical specification is not an exhaustive resource for the design, installation, operation or maintenance of generator sets but is more focused on recommendations to provide strategies on selection and criteria which may affect the use of such generation systems in a rural electrification project. Two cases will be considered as illustrated by Figure 1 to power a collective electrification system (microgrid) or an individual electrification system. • the micropowersystem is composed of one generator set • the micropowersystem is a hybrid one and the generator set is only part of it. This case is addressed in the document dedicated to micropower system (IEC/TS 62257-9-1). The aim of this technical specification is to provide users with the appropriate levels of reliability and safety of the equipment during its estimated service lifespan. It describes the minimum safety requirements and does not claim to be an exhaustive instruction manual or design specification. Compliance with this technical specification does not exempt any person, organization or corporation from the responsibility to comply with all other relevant regulations. This technical specification gives recommendations for the following types of generator sets: a) single phase; b) three phase; c) LV range up to 500 V - 50/60 Hz (see IEC/TS 62257-9-2).

Recommendations for small renewable energy and hybrid systems for rural electrification - Part 7-3: Generating set - Selection of generating sets for rural electrification systems

IEC TS 62257-7:2008 农村电气化用小型可再生能源和混合系统的建议.第7部分:发电机

The purpose of this part of IEC 62257 is to specify the general requirements for generators (maximum power = 100 kVA) in decentralized rural electrification systems. The aim is to point out the main items that must be considered when selecting, sizing, installing, operating and maintaining this equipment. This technical specification is a general introduction followed by more specific documents dedicated to the generation technologies which are the most currently used in rural electrification projects.

Recommendations for small renewable energy and hybrid systems for rural electrification - Part 7: Generators

DIN EN 60034-9 Berichtigung 1:2008 旋转电机.第9部分:噪声极限(IEC 60034-9-2003、修改件 + A1-2007).勘误表DIN EN 60034-9(VDE 0530-9)-2008-01

Rotating electrical machines - Part 9: Noise limits (IEC 60034-9:2003, modified + A1:2007); German version EN 60034-9:2005 + A1:2007, Corrigenda to DIN EN 60034-9 (VDE 0530-9):2008-01

DIN EN 61800-5-1:2008 可调速电力传动系统.第5-1部分:安全要求.电、热和能量

Adjustable speed electrical power drive systems - Part 5-1: Safety requirements - Electrical, thermal and energy (IEC 61800-5-1:2007); German version EN 61800-5-1:2007

DIN EN 60034-8:2008 旋转电机.第8部分:终端标志和旋转方向

Rotating electrical machines - Part 8: Terminal markings and direction of rotation (IEC 60034-8:2007); German version EN 60034-8:2007

DIN EN 61800-5-2:2008 可调速的电动系统.第5-2部分:安全要求.功能

Adjustable speed electrical power drive systems - Part 5-2: Safety requirements - Functional (IEC 61800-5-2:2007); German version EN 61800-5-2:2007

DIN EN 60034-12:2008 旋转电机.第12部分:单速三相鼠笼式感应电动机的启动性能

Rotating electrical machines - Part 12: Starting performance of single-speed three-phase cage induction motors (IEC 60034-12:2002 + A1:2007); German version EN 60034-12:2002 + A1:2007

IEC 2/1498/CD:2008 IEC 60034-24:旋转电机.第24部分:旋转电机和轴承杂散电流有源部件潜在故障的探测和诊断

IEC 60034-24: Rotating electrical machines - Part 24: Detection and diagnosis of potential failures at the active parts of rotating electrical machines and of bearing currents - Application guide

KS C IEC TR 61800-6:2008 可调速电力驱动系统.第6部分:负载类型和相应电流额定值的测定指南

이 기술보고서는 가변속 전력 구동시스템(PDS)과 특히 기본 구동모듈(BDM)에 대한 정격

Adjustable speed electrical power drive systems-Part 6:Guide for determination of types of load duty and corresponding current ratings

KS C IEC 61800-3:2008 可调速电力传动系统.第3部分:包括特定试验方法的电磁兼容(EMC)产品标准

이 규격에서는 전력구동시스템(PDS)에 대한 전자기 적합성(EMC) 요건을 규정한다. PD

Adjustable speed electrical power drive systems－Part 3：EMC requirements and specific test methods

UL 2201 BULLETIN-2008 便携式发动机驱动式发电机调查大纲

This standard specifies the outline of investigation for portable engine-generator assemblies

OUTLINE OF INVESTIGATION FOR PORTABLE ENGINE-GENERATOR ASSEMBLIES

SANS 60034-2-1:2008 旋转电机.第2-1部分:采用试验来确定损失及效率的标准方法(不包括牵引车辆的旋转电机)

Establishes methods of determining efficiencies from tests, and also specifies methods of obtaining losses.

Rotating electrical machines Part 2-1: Standard methods for determining losses and efficiency from tests (excluding machines for traction vehicles)

SANS 61800-5-1:2008 可调速电力驱动系统.第5-1部分:安全要求.电、热及能量

Applies to adjustable speed electric drive systems, including power conversion, drive control and motors, and covers electrical, thermal and energy safety. Applies to d.c. drive systems connected to 1 kV a.c., 50 Hz or 60 Hz and a.c. drive systems with c

Adjustable speed electrical power drive systems Part 5-1: Safety requirements - Electrical, thermal and energy

UL 2111 CRD-2008 电动机过热保护的UL安全标准. 节/段落参考: 7, 8, 9, 14, 15, 16主题: 在对阻抗保护电动机和含有自动复位热电动机保护器 (TMP) 的电动机进行锁定转子试验过程中的电源中断 (第一版: 1997年3月28日)

UL Standard for Safety Overheating Protection for Motors - Section / Paragraph Reference: 7, 8, 9, 14, 15, 16 Subject: Power Interruption During Locked Rotor Tests on Impedance Protected Motors and Motors Containing Automatic Reset Thermal Motor Protector

IEC 60034-29:2008 旋转电机.第29部分:等效加载和迭加技术.测定温升的间接试验

This international Standard applies to machines covered by IEC 60034-1 when they connot be lodaded to a specific condition (tated or otherwise). It is applicable to both motors and generators.

Rotating electrical machines - Part 29: Equivalent loading and superposition techniques - Indirect testing to determine temperature rise

DIN EN 60034-14:2008 旋转电机.第14部分:轴中心高56mm及以上电机的机械振动.振动强度的测量、评价和限值

Rotating electrical machines - Part 14: Mechanical vibration of certain machines with shaft heights 56 mm and higher - Measurement, evaluation and limits of vibration severity (IEC 60034-14:2003 + A1:2007); German version EN 60034-14:2004 + A1:2007

SANS 1470-2:2008 声功率标识.第2部分:焊接用发电机

Covers the requirements for the labelling of welding generators with a noise emission value and specifies the test method to be used for the verification of the labelled value.

Sound power labelling Part 2: Welding generators

NF C01-411/A1:2008 国际电工词汇.第411章:旋转电机

Electrotechnical Vocabulary - Chapter 411 : rotating machines.