K20 旋转电机综合 标准查询与下载

DIN EN 60034-28:2008 旋转电机.第28部分:低压三相鼠笼型感应电动机用等效电路图数量测定的试验方法

Rotating electrical machines - Part 28: Test methods for determining quantities of equivalent circuit diagrams for three-phase low-voltage cage induction motors (IEC 60034-28:2007); German version EN 60034-28:2007

BS EN 60034-2-1:2007 旋转电机.第2-1部分:(不包括牵引车辆用电机)试验中损失和功效的测定用标准方法

This part of IEC 60034 is intended to establish methods of determining efficiencies from tests, and also to specify methods of obtaining specific losses. This standard applies to d.c. machines and to a.c. synchronous and induction machines of all sizes within the scope of IEC 60034-1. NOTE These methods may be applied to other types of machines such as rotary converters, a.c. commutator motors and single-phase induction motors.

Rotating electrical machines. Part 2-1: Standard methods for determining losses and efficiency from tests (excluding machines for traction vehicles)

DIN EN 60034-9:2008 旋转电机.第9部分:噪声极限值

Rotating electrical machines - Part 9: Noise limits (IEC 60034-9:2003, modified + A1:2007); German version EN 60034-9:2005 + A1:2007

IEC 2/1482/DTS:2008 IEC/TS 60034-18-42:旋转电机.第18-42部分:电压转换器馈电的旋转电机用抗局部放电电气绝缘系统(II型)的鉴定和验收试验

IEC/TS 60034-18-42: Rotating electrical machines - Part 18-42: Qualification and acceptance tests for partial discharge resistant electrical insulation systems (Type II) used in rotating electrical machines fed from voltage converters

ANSI/ISA 96.02.01-2008 阀门电力传动装置的规范指南

This standard provides general requirements for the development of specifications for electric actuators. This standard is not intended to address the range of compact, light duty low torque electric actuators typically rated for less than 5.65 Nm (50 inch-lbs).

Guidelines for the Specification of Electric Valve Actuators

GOST R 53148-2008 旋转电机.噪声限值

Rotating electrical machines. Noise limits

IEC 60034-18-42:2008

ANSI/NEMA 250-2008 电气设备附件(最大为1000 Volts)

This standard covers enclosures for electrical equipment rated not more than 1000 Volts and intended to be installed and used as follows: a. Non-hazardous (non-classified) locations 1. Enclosures for indoor locations, Types 1, 2, 5, 12, 12K, and 13; and 2. Enclosures for indoor or outdoor locations, Types 3, 3X, 3R, 3RX, 3S, 3SX, 4, 4X, 6, and 6P. b. Hazardous (classified) locations 1. Enclosures for indoor locations, Types 7 and 9; 2. Enclosures for indoor or outdoor locations, Type 8; and 3. Enclosures for mining applications, Type 10.

Enclosures for Electrical Equipment (1000 Volts Maximum)

NF C51-312/A1:2007 旋转电机.第12部分:单速三相鼠笼式感应电动机的起动性能

Rotating electrical machines - Part 12 : starting performance of single-speed three-phase cage induction motors.

DIN VDE 0530-17:2007 旋转电机.第17部分:变频供电的笼型感应电动机.应用指南

Rotating electrical machines - Part 17: Cage induction motors when fed from converters - Application guide (IEC/TS 60034-17:2006)

BS EN 61800-5-2:2007 可调速电力驱动系统.安全要求.功能

This part of IEC 61800 specifies requirements and makes recommendations for the design and development, integration and validation of PDS(SR)s in terms of their functional safety considerations. It applies to adjustable speed electric drive systems covered by the other parts of the IEC 61800 series of standards. This International Standard is only applicable where functional safety of a PDS(SR) is claimed and the PDS(SR) is operating in the high demand or continuous mode (see 3.10). For low demand applications, see IEC 61508. This part of IEC 61800, which is a product standard, sets out safety-related considerations of PDS(SR)s in terms of the framework of IEC 61508, and introduces requirements for PDS(SR)s as subsystems of a safety-related system. It is intended to facilitate the realisation of the electrical/electronic/ programmable electronic (E/E/PE) elements of a PDS(SR) in relation to the safety performance of safety function(s) of a PDS. Manufacturers and suppliers of PDS(SR)s by using the normative requirements of this part of IEC 61800 will indicate to users (control system integrators, machinery and plant designers, etc.) the safety performance for their equipment. This will facilitate the incorporation of a PDS(SR) into a safety-related control system using the principles of IEC 61508, and possibly its specific sector implementations (for example IEC 61511, IEC 61513, IEC 62061) or ISO 13849. Conformity with this part of IEC 61800 fulfils all the requirements of IEC 61508 that are necessary for a PDS(SR). This part of IEC 61800 does not specify requirements for: • the hazard and risk analysis of a particular application; • the identification of safety functions for that application; • the initial allocation of SILs to those safety functions; • the driven equipment except for interface arrangements; • secondary hazards (for example from failure in a production or manufacturing process); • the electrical, thermal and energy safety considerations, which are covered in IEC 61800-5-1; • the PDS(SR) manufacturing process; • the validity of signals and commands to the PDS(SR). This part of IEC 61800 only applies to PDS(SR)s implementing safety functions with a SIL not greater than SIL 3.

Adjustable speed electrical power drive systems. Safety requirements. Functional

SANS 1594:2007 人工操作起动机

Specifies requirements for chain blocks that require the use of a hand chain for hoisting and lowering.

Manually operated chain blocks

IEC 60034-3:2007 旋转电机.第3部分:用蒸汽涡轮机或燃气涡轮机驱动的同步发电机用特殊需求

This part of IEC 60034 applies to three-phase synchronous generators, having rated outputs of 10 MVA and above driven by steam turbines or combustion gas turbines. It supplements the basic requirements for rotating machines given in IEC 60034-1. Common requirements are prescribed together with specific requirements for air, for hydrogen or for liquid cooled synchronous generators. This part of IEC 60034 also gives the precautions to be taken when using hydrogen cooled generators including: – rotating exciters driven by synchronous generators; – auxiliary equipment needed for operating the generators; – parts of the building where hydrogen might accumulate. NOTE 1 These requirements also apply to a synchronous generator driven by both a steam turbine and a combustion gas turbine as part of a single shaft combined cycle unit. NOTE 2 These requirements do not apply to synchronous generators driven by water (hydraulic) turbine or wind turbine. NOTE 3 The precautions to be taken when using hydrogen are valid for all cases where hydrogen is used as a coolant.

Rotating electrical machines - Part 3: Specific requirements for synchronous generators driven by steam turbines or combustion gas turbines

IEC 61800-7-1:2007 可调速电力传动系统.第7-1部分:通用接口和电力驱动系统断面的使用.接口定义

IEC 61800-7 specifies profiles for power drive systems (PDS) and their mapping to existing communication systems by use of a generic interface model. The functions specified in this part of IEC 61800-7 are not intended to ensure functional safety. This requires additional measures according to the relevant standards, agreements and laws. This part of IEC 61800-7 specifies a generic interface between power drive system(s) (PDS) and the application control program in a controller. The generic PDS interface is not specific to any particular communication network technology. Annexes of this part of IEC 61800-7 specify the mapping of the different drive profiles types onto the generic PDS interface.

Adjustable speed electrical power drive systems - Part 7-1: Generic interface and use of profiles for power drive systems - Interface definition

IEC 61800-7-204:2007 可调速电力传动系统.第7-204部分:电力传动系统用剖面图的使用和通用接口.4型剖面图的规范

IEC 61800-7 specifies profiles for Power Drive Systems (PDS) and their mapping to existing communication systems by use of a generic interface model. The functions specified in this part of IEC 61800-7 are not intended to ensure functional safety. This requires additional measures according to the relevant standards, agreements and laws. This part of IEC 61800-7 specifies profile type 4 for Power Drive Systems (PDS). Profile type 4 can be mapped onto different communication network technologies.

Adjustable speed electrical power drive systems - Part 7-204: Generic interface and use of profiles for power drive systems - Profile type 4 specification

IEC 61800-7-303:2007 可调速的电驱动系统.第7-303部分:电力传动系统用剖面图的使用和通用接口.3型剖面图映射到网络技术

IEC 61800-7 specifies profiles for Power Drive Systems (PDS) and their mapping to existing communication systems by use of a generic interface model. The functions specified in this part of IEC 61800-7 are not intended to ensure functional safety. This requires additional measures according to the relevant standards, agreements and laws. This part of IEC 61800 7 specifies how the profile type 3 (PROFIdrive) specified in IEC 61800-7-203 onto different network technologies. – PROFIBUS DP, see Clause 4, – PROFINET IO, see Clause 5.

Adjustable speed electrical power drive systems - Part 7-303: Generic interface and use of profiles for power drive systems - Mapping of profiles type 3 to network technologies

IEC 61800-7-203:2007 可调速电力传动系统.第7-203部分:电力传动系统用剖面图的使用和通用接口.3型剖面图的规范

IEC 61800-7 specifies profiles for Power Drive Systems (PDS) and their mapping to existing communication systems by use of a generic interface model. The functions specified in this part of IEC 61800-7 are not intended to ensure functional safety. This requires additional measures according to the relevant standards, agreements and laws. This part of IEC 61800-7 specifies profile type 3 for Power Drive Systems (PDS). Profile type 3 can be mapped onto different communication network technologies.

Adjustable speed electrical power drive systems - Part 7-203: Generic interface and use of profiles for power drive systems - Profile type 3 specification

IEC 61800-7-304:2007 可调速电源驱动系统.第7-304部分:电力传动系统用剖面图的使用和通用接口.4型剖面图映射到网络技术

IEC 61800-7 specifies profiles for Power Drive Systems (PDS) and their mapping to existing communication systems by use of a generic interface model. The functions specified in this part of IEC 61800-7 are not intended to ensure functional safety. This requires additional measures according to the relevant standards, agreements and laws. This part of IEC 61800-7 specifies the mapping of the profile type 4 (SERCOS) specified in IEC 61800-7-204 onto different network technologies. – SERCOS I / II, see Clause 5, – SERCOS III, see Clause 6, – EtherCAT, see Clause 7.

Adjustable speed electrical power drive systems - Part 7-304: Generic interface and use of profiles for power drive systems - Mapping of profiles type 4 to network technologies

IEC 2/1478/CD:2007 IEC/TS 60034-18-33:旋转电机.第18-33部分:绝缘系统的功能评估.用于旋转电机的绝缘系统在热和电应力共同作用下耐久性的散绕绕组多功能评估用试验程序

IEC/TS 60034-18-33: Rotating electrical machines - Part 18-33: Functional evaluation of insulation systems - Test procedures for multifunctional evaluation of form-wound windings by endurance under simultaneous thermal and electrical stresses of insulatio

IEC 61800-7-301:2007 可调速电源驱动系统 第7-301部分 电力传动系统用剖面图的使用和通用接口 1型剖面图映射到网络技术

IEC 61800-7 specifies profiles for Power Drive Systems (PDS) and their mapping to existing communication systems by use of a generic interface model. The functions specified in this part of IEC 61800-7 are not intended to ensure functional safety. This requires additional measures according to the relevant standards, agreements and laws. This part of IEC 61800-7 specifies the mapping of the profile type 1 (CiA 402) specified in IEC 61800-7-201 onto different network technologies. – CANopen, see Clause 5; – EtherCAT, see Clause 6; – ETHERNET Powerlink, see Clause 7.

Adjustable speed electrical power drive systems - Part 7-301: Generic interface and use of profiles for power drive systems - Mapping of profiles type 1 to network technologies