K30 低压电器综合 标准查询与下载

SN/T 1431.1-2011 进出口低压电器检验规程.第1部分：通用要求

本部分规定了进出口低压电器的抽样、检验及结果判定。 本部分适用于交流50Hz(或60Hz)，额定电压交流不超过1000V或直流不超过1500 V电路中 起通断、保护、控制或调节作用电器的检验。额定交流电压1000 V～1200 V的电器可参照本部分执行。 本部分所涵盖的低压电器产品国家标准见附录A。

Rules for the inspection of low-voltage electrical apparatus for import and export.Part 1: General requirements

SN/T 1431.4-2011 进出口低压电器检验规程.第4部分：机电式接触器和电动机起动器

本部分规定了进出口机电式接触器和电动机起动器的抽样、检验及结果判定。 本部分适用于主触头额定电压交流不超过1 OOO V或直流不超过1 500 V的机电式接触器和电动机起动器的检验。 本部分不适用于以下产品的检验： —直流起动器； 一特殊用途和在起动位置连续运行的星-三角起动器、转子变阻式起动器及两级自耦减压起动器； —不平衡转子变阻式起动器； —不仅用于起动而且用于调速的起动器； —液态起动器和"液态-汽态"起动器； —半导体接触器和在主电路中使用半导体接触器的起动器； —定子变阻式起动器； —特殊用途的接触器和起动器； —接触器的辅助触头和接触器式继电器的触头。

Rules for the inspection of low-voltage electrical apparatus for import and export.Part 4:Low-voltage electromechnical contactors and motor starters installations

UL SUBJECT 3730-2011 光伏接线盒调查大纲

1.1 These requirements cover photovoltaic junction boxes intended to be attached to phovoltaic modules and panels. 1.2 These requirements cover photovoltaic junction boxes intended for factory and field wiring and may include conduit openings, wiring leads, and/or photovoltaic connectors intended for interconnection of PV modules. 1.3 The products covered by these requirements are intended to be installed in accordance with the National Electrical Code, ANSI/NFPA 70.

Outline of Investigation for Photovoltaic Junction Boxes

BS EN 50065-1:2011 频率范围为3 KHz-148,5 KHz的低压电气设备的信号传输.一般要求,频带和电磁干扰

This standard applies to electrical equipment using signals in the frequency range 3 kHz to 148,5 kHz to transmit information on low voltage electrical systems, either on the public electricity distribution network or within installations in consumers’ premises. It specifies the frequency bands allocated to the different applications, limits for the terminal output voltage in the operating band and limits for conducted and radiated disturbance. It also gives the methods of measurement. It does not specify the modulation methods, the coding methods or functional features (except those for the prevention of mutual interference). Environmental requirements and tests are not included. NOTE 1 Compliance with this standard does not imply permission to establish communication with locations outside the consumer’s installation or with other consumers through the public electricity distribution network where this would not otherwise be allowed. The object of the standard is to limit mutual influence between transmission equipment in electrical installations and between such equipment and other equipment. In addition this standard is intended to limit interference caused by signal transmission equipment to sensitive electronic equipment. However, complete freedom from such interference cannot be assured. NOTE 2 Designers should consider signalling systems in conformance with this standard when determining immunity for electrical equipment.

Signalling on low-voltage electrical installations in the frequency range 3 kHz to 148,5 kHz. General requirements, frequency bands and electromagnetic disturbances

UL 60320-1 (ND)-2011 家用和类似用途的UL 60320-1器具耦合器的国家差异. 第1部分: 通用要求

National Differences For UL 60320-1 Appliances Couplers for Household and Similar General Purposes - Part 1: General Requirements (Second Edition; Reprint with revisions through and including July 23, 2015)

UL 60320-1-2011 家用和类似用途设备耦合器.第1部分:一般要求

Appliance couplers for household and similar general purposes - Part 1: General requirements

UL 60947-7-3-2011 低压开关设备和控制设备.第7-3部分:辅助设备.熔丝接线板安全要求

Low-voltage switchgear and controlgear - Part 7-3: Ancillary equipment - Safety requirements for fuse terminal blocks

NF C13-200F1:2011 关于2009年9月NF C13-200标准的第F1号解读手册.

Interpretation Manual No. F1 on the September 2009 NF C13-200 standard.

IEC 60906-2:2011 家用和类似用途插头插座的IEC系统.第2部分:插头和插座.交流15 A 125 V和20 A 125 V

Scope and object This part of 60906 applies to the IEC system of plugs and socket-outlets rated 15 A 125 V a.c. and 20 A 125 V a.c. for household and similar purposes@ for the connection of equipment to distribution systems having nominal voltages between 100 V and 130 V a.c. in so far as dimensional requirements are concerned. Socket-outlets in this standard are classified according to intended use@ in a) socket-outlets for circuits where a single earthing circuit provides protective earthing for connected equipment and exposed conductive parts of the socket-outlet@ if any; b) socket-outlets for circuits where electrical noise immunity is desired for the earthing circuit of connected equipment. The equipment earthing circuit is electrically separated from the protective earthing circuit provided for the exposed conductive parts of the socket-outlet@ if any. For plugs and socket-outlets rated 16 A 250 V a.c. for household and similar purposes@ refer to IEC 60906-1.

IEC system of plugs and socket-outlets for household and similar purposes - Part 2: Plugs and socket-outlets - 15 A 125 V a.c. and 20 A 125 V a.c.

IEC 60947-8:2003/AMD2:2011 低压开关设备和控制设备.第8部分:旋转电机用嵌入式热保护(PTC)控制装置

This part of IEC 60947 specifies rules for control units@ which perform the switching functions in response to the thermal detectors incorporated in rotating electrical machines according to IEC 60034-11@ and the industrial application.It specifies rules for that type of system comprising a positive temperature coefficient (PTC) thermistor detector having particular characteristics@ and its associated control unit.The PT100 detectors are covered by IEC 60751@ where the resistor values are given according to the temperatures of the detector. The present rules lay down the characteristics of association of this particular positive temperature coefficient thermistor detector and its associated control unit (designated ??Mark A detector?? and ??Mark A control unit??)@ when they are used in thermal protection systems.NOTE It is not possible to specify all the requirements for the operating characteristics of a control unit@ as they are dependent on some aspects of the thermal detectors. Some aspects of the requirements of the thermal protector system can only be specified when account is taken of the characteristics of the rotating machine to be protected and the method of installation of the detector within the machine.For these reasons@ for each characteristic it is necessary to specify who is responsible for stating the required values and who is responsible for compliance with the requirement and for carrying out any confirmatory test.

Low-voltage switchgear and controlgear - Part 8: Control units for built-in thermal protection (PTC) for rotating electrical machines

NF C63-421-5:2011 低压开关设备和控制装置组件.第5部分:公共电网配电用配件

Low-voltage switchgear and controlgear assemblies - Part 5 : assemblies for power distribution in public networks.

BS EN 61439-5:2011 低压开关装置和控制装置.公共网络配电用配件

This clause of Part 1 applies with the following additions. Addition: This standard gives specific requirements for public electricity network distribution assemblies (PENDAs), which are stationary assemblies verified by verification tests, as defined in this standard. These ASSEMBLIES are used for the distribution of electrical energy in three-phase systems (see Figure 101 for a typical distribution network). Open type ASSEMBLIES are not covered by this standard. The object of this standard is to state the definitions and to specify the service conditions, construction requirements, technical characteristics and tests for PENDAs. Network parameters may require tests at higher performance levels. NOTE 1 If a PENDA is equipped with additional equipment (for example meters), in such a way that the main function is changed considerably, then other standards may also apply as agreed between user and manufacturer (see 8.5). NOTE 2 Where local regulations and practices permit, a PENDA according to this standard may be used in other than public networks. PENDAs are suitable for installation in places where only skilled persons have access for their use, however, outdoor types may be installed in situations that are accessible to ordinary persons.

Low-voltage switchgear and controlgear assemblies. Assemblies for power distribution in public networks

IEC 60947-1:2011 低压开关装置和控制器.第1部分:一般规则

Low-voltage switchgear and controlgear - Part 1: General rules

IEC 60364-7-718:2011 低压电气装置.第5-718部分:专门安装或位置的要求.公共设施和工作场所

Low-voltage electrical installations - Part 7-718: Requirements for special installations or locations - Communal facilities and workplaces

IEC 60947-4-3/AMD2:2011 低压开关装置和控制器.第4-3部分:接触器和电动机启动器.非电动机负荷用交流半导体电动机控制器和接触器

Low-voltage switchgear and controlgear - Part 4-3: Contactors and motor-starters - AC semiconductor motor controllers and contactors for non-motor loads

IEC 60884-2-7:2011 家用和类似用途的插头插座 第2-7部分:电线加长装置详细要求

Replacement: This Part of IEC 60884 applies to cord extension sets@ rewirable and non rewirable@ with or without earthing contact@ with a rated voltage greater than 50 V but not exceeding 440 V and a rated current not exceeding 16 A@ intended for household and similar purposes@ either indoors or outdoors. NOTE 1 In the following countries@ cord extension sets only for equipment of class II are not allowed: DE@ UK and CZ. NOTE 2 In the following country@ rewirable cord extension sets are not allowed: ZA. This standard does not apply to cord extension sets with means for reeling. This standard also applies to cord extension sets which are intended to be used in a cable reel@ and which therefore become cable reels with a detachable flexible cable. For the combination of the cord extension set@ the reel requirements and tests of IEC 61242 have to be fulfilled in addition. Cord extension sets should be suitable for use at ambient temperatures not normally exceeding +40 ?C@ but their average over a period of 24 h does not exceed +35 ?? with a lower limit of the ambient air temperature of ?C5 ??

Plugs and socket-outlets for household and similar purposes - Part 2-7: Particular requirements for cord extension sets

IEC TR 60664-2-1:2011 低压系统内设备的绝缘配合.第2-1部分:应用指南.IEC 60664标准系列,尺寸标注范例和介质试验的应用说明

This part of IEC 60664, which is a technical report, serves as an application guide for technical committees and manufacturers specifying dimensioning requirements for products in accordance with the IEC 60664 series. The significant items for consideration are as follows: a) nominal system voltage(s) or rated insulation voltage(s); b) overvoltage category of the products (OV cat.); c) any type of overvoltages; d) frequency of the voltage; e) characteristics of the solid insulating material; f) pollution degree and humidity levels.

Insulation coordination for equipment within low-voltage systems - Part 2-1: Application guide - Explanation of application of the IEC 60664 series, dimensioning examples and dielectric testing

ANSI/UL 60947-4-1A-2011 低压开关设备和控制设备安全标准.第4-1部分:接触器和电机启动器.电机接触器和电机启动器

Covers: Harmonization of IEC utilization categories with the UL ratings for control of external loads.

Standard for Safety for Low-Voltage Switchgear and Controlgear - Part 4-1: Contactors and Motor-Starters - Electromechanical Contactors and Motor-Starters

DIN EN 60947-4-1:2011 低压开关设备和控制设备.第4-1部分:接触器和电机启动器.机电式接触器和电机启动器(IEC 60947-4-1-2009);德文版本EN 60947-4-1-2010

Low-voltage switchgear and controlgear - Part 4-1: Contactors and motor-starters - Electromechanical contactors and motor-starters (IEC 60947-4-1:2009); German version EN 60947-4-1:2010

ANSI/UL 60320-1-2011 现行家用和类似用途的设备耦合器的标准.第1部分:一般要求

1. Proposed Adoption of the Standard for Appliance Couplers for Household and Similar General Purposes - Part 1: General Requirements, IEC 60320-1 with Harmonized National Differences as the Proposed Second Edition of the Standard for Appliance Couplers for Household and Similar General Purposes - Part 1: General Requirements, UL 60320-1.

Standard for Appliance Couplers for Household and Similar General Purposes - Part 1: General Requirements