K30 低压电器综合 标准查询与下载

KS C IEC 60269-2:2009 低压熔断器.第2部分:专职人员使用的熔断器补充要求

전문가용 퓨즈는 일반적으로 전문가만 퓨즈에 접근하거나 퓨즈를 교환할 수 있도록 장치가 설계

Low-voltage fuses－Part 2：Supplementary requirements for fuses for use by authorized persons(fuses mainly for industrial application)－Examples of standardized systems of fuses A to I

KS C IEC 60269-3:2009 低压熔断器.第3部分:非熟练人员使用的熔断器(主要是家用和类似用途的熔断器)的补充要求

KS C IEC 60269-1의 모든 부속절 및 그와 관련된 퓨즈 시스템의 요구사항들에 부

Low-voltage fuses-Part 3:Supplementary requirements for fuses for use by unskilled persons (fuses mainly for household and similar applications)

KS C IEC 60664-1:2009 低压系统内设备的绝缘配合.第1部分:原则、要求和试验

이 표준은 저압기기의 절연협조를 규정하며, 직류 1 500 V 이하 또는 30 kHz 이하

Insulation coordination for equipment within low-voltage systems-Part 1:Principles, requirements and tests

KS C IEC 60269-1:2009 低压熔断器.第1部分:通用要求

이 표준은 공칭전압 1 000 V 이하의 상용 주파 교류 회로나 1 500 V 이하의 직류

Low-voltage fuses-Part 1:General requirements

ANSI/EIA 364-1000:2009 受控环境设施用电气连接器和插座的性能评估用环境试验方法论

Establishes the test procedures and test sequences to be followed when evaluating the performance of electrical connectors and sockets used in controlled environments.

Environmental Test Methodology for Assessing the Performace of Electrical Connectors and Sockets Used in Controlled Environment Applications

ANSI/EIA 364-1000.01B:2009 受控环境设施用电气连接器和插座的性能评估用环境试验方法论

This standard is being superseded by EIA-3645-1000.

Environmental Test Methodology for Assessing the Performance of Electrical Connectors and Sockets Used in Controlled Environment Applications

ANSI/EIA 364-65B:2009 电气连接器和插座用混合流动气体试验方法

Establishes the test procedure for producing environmentally related corrosive atmospheres to determine the reaction of plated or unplated surfaces when exposed to different concentrations of flowing gas mixtures

Mixed Flowing Gas Test Procedure for Electrical Connectors and Sockets

KS C IEC 62026-3:2008 低压开关装置和控制装置.控制器装置接口(CDIs).第3部分:器件网络(DeviceNet)

이 표준은 단일 제어기 또는 복수의 제어기와 제어 회로 기기 또는 스위칭 소자 사이의 인터

Low-voltage switchgear and controlgear－Controller-device interfaces(CDIs)－Part 3：DeviceNet

NRS 022-2008 电力分配.拉线系统及相关部件

Covers a rationalized range of stays and associated components intended for use where supplementary structural support is required for poles in an overhead electricity distribution system that operates at voltages up to 44 kV.

Electricity distribution - Stays and associated components

KS C IEC 62026-1:2008 低压开关装置和控制装置.控制器装置接口(CDIs).第1部分:通用规则

이 표준은 저전압 배전반, 제어반과 제어기(예를 들어 프로그램 가능 제어기, 퍼스널 컴퓨터

Low-voltage switchgear and controlgear－Controller-device interfaces(CDIs)－Part 1：General rules

KS C IEC 60309-2:2008 工业用插头.插座和耦合器.第2部分:针头和接触管附件的尺寸可转换性要求

이 표준은 주파수가 500 Hz 이하 정격 전류가 125 A 이하 또는 정격 전압이 690

Plugs, socket-outlets and couplers for industrial purposes-Part 2:Dimensional interchangeability requirements for pin and contact-tube accessories

KS C IEC 60439-2:2008 低压开关设备和控制设备组件.第2部分:母线干线系统的特殊要求(线路)

이 표준은 주거지역, 상가지역, 공공지역, 농업지역 및 산업지역의 전력공급 및 배전을 위한

Low-voltage switchgear and controlgear assemblies-Part 2:Particular requirements for busbar trunking systems(busways)

KS C IEC 60309-1:2008 工业用插头.插座和耦合器.第1部分:通用要求

이 표준은 산업용 옥내/옥외의 250 A 이하의 정격 전류, 직류/교류 690 V 이하의

Plugs, socket-outlets and couplers for industrial purposes-Part 1:General requirements

NF C15-100/A2:2008 低压电气装置

Low-voltage electrical installations.

SANS 61641:2008 封闭式低压开关设备及控制设备.内部故障引发电弧条件下的测试指南

Gives guidance on the method of testing of enclosed low-voltage switchgear and controlgear assemblies under conditions of arcing in air due to an internal fault.

Enclosed low-voltage switchgear and controlgear assemblies - Guide for testing under conditions of arcing due to internal fault

DIN EN 61915-1:2008 低压开关装置和控制器.网络化工业装置的装置轮廓.第1部分:设计轮廓的开发用通用规则

The IEC 61915 series is intended to improve interoperability of devices, network tools and application software. This part of IEC 61915 defines a framework for common representation of networked industrial devices and provides a template for documenting such a representation, independent of the network used. This framework follows the principles given in IEC/TR 62390, the "Common automation device - Profile guideline", and refers to ISO 15745, "Industrial automation systems and integration - Open systems application integration framework". NOTE I The device profile format specified in this part of lEC 61915 is compatible with devices connected to both bit-and byte-oriented networks. This part of IEC 61915 applies to root device profiles, generic device profiles, and specific device profiles. The root device profiles will be published in subsequent parts of the IEC 61915 series. NOTE2 This International Standard is specifically intended for products covered by the lEC 60947 series. NOTE3 Organisations such as consortia are encouraged to use the rules defined in this part of IEC61915 to develop generic device profiles for use within their own organisations. Users (product manufacturers and other organizations) should use the root device profiles together with the rules defined in this part of IEC61915. This part of IEC61915 allows users to make extensions to the root device profiles and/or generic device profiles. Where no suitable root device profile exists, the user may develop generic or specific device profiles using the rules defined in this part of IEC 61915. This part of IEC 61915 recommends the use of a profile exchange language for representation of the device profile information in order to facilitate the profile's use by network tools and application softwa re. NOTE 4 The types of devices may vary from simple devices, such as pilot lights, push-buttons and limit switches, to more complex devices with many bytes of information, such as motor controllers, semiconductor motor starters, etc.

Low-voltage switchgear and controlgear - Device profiles for networked industrial devices - Part 1: General rules for the development of device profiles (IEC 61915-1:2007); English version EN 61915-1:2008

BS 1363-5:2008 13A插头、电源插座、适配器和连接装置.装有保险丝的转换插头用规范

This Part of BS 1363 specifies requirements, with particular reference to safety in normal use, for 13 A, fused, conversion plugs for household, commercial and light industrial purposes. The scope of the standard covers two-pole plus earth conversion plugs that are either reusable or non-reusable and that are suitable for the connection of non-BS 1363 type plugs, conforming to a recognized standard, to socket-outlets conforming to BS 1363-2. The scope of this standard is limited to devices with the following characteristics: • that have insulating sleeves on line and neutral pins; • that have one plug portion and one set of contacts intended to connect to a non-BS 1363 type plug that conforms to the dimensional requirements of a standard listed in IEC TR 60083; • that are suitable for the connection of electrical equipment in a.c. circuits only, operating at voltages not exceeding 250 V r.m.s. at 50 Hz; • that may have the un-terminated metal earth pin replaced with a similarly dimensioned insulated shutter opening device (ISOD) designed to operate the shutter mechanism of a socket-outlet conforming to BS 1363-2. NOTE A metal earth pin can be brass, copper, phosphor-bronze or other metal at least equivalent with regard to its conductivity, resistance to abrasion, and resistance to corrosion. Two categories of conversion plugs are specified, covering normal and rough use. Conversion plugs specified in this standard are intended for the connection of loads to socket outlets; they are not intended for the connection of electrical power generators to socket outlets. Conversion plugs incorporating switches, transformers, thermostats, or other control means are outside the scope of this Part of BS 1363. This standard also does not cover: • non-BS 1363 type conversion plugs, i.e. with a contact set to fit 13 A plugs, and a male plug portion suitable for a non-BS 1363 type socket outlet; or • adaptors (as to which, see BS 1363-3).

13 A plugs, socket-outlets, adaptors and connection units - Specification for fused conversion plugs

UL 2459-2008 绝缘的多极分线连接器

1.1 This Standard covers insulated multi-pole mating or non-mating splicing wire connectors intended for field wiring and factory wiring for use in accordance with the Canadian Electrical Code, Part I, in Canada, and NFPA 70, National Electrical Code, in the United States. 1.2 These wire connectors are intended to facilitate the connection of devices, such as prefabricated wiring assemblies, smoke detectors, and lighting products, to the branch circuit conductors of buildings. 1.3 These wire connectors may additionally be used internal to luminaries to facilitate replacement of the ballast and may not be directly attached to the branch circuit conductors. These wire connectors are suitable for one or more conductors per contact. 1.4 These wire connectors are suitable for use with 30 to 6 AWG (0.05 to 13.3 mm2) stranded copper conductors and 30 to 10 AWG (0.05 to 5.3 mm2) solid copper conductors. 1.5 These wire connectors are suitable for currents not exceeding the ampacity of insulated conductors or as rated by the manufacturer. 1.6 These wire connectors are suitable for voltages not exceeding 600 V. 1.7 This Standard does not apply to (a) splicing wire connectors intended for direct burial; (b) insulated splicing wire connectors intended for use at voltage levels exceeding 600 V (1000 V in a sign or luminaire); (c) terminal wire connectors; (d) wire binding screw terminals; (e) built-in terminal connectors on devices having integral cable clamps; (f) flat quick-connect terminals; (g) devices, such as wire connectors and soldering lugs, that are covered by (i) CAN/CSA-C22.2 No. 65 or UL 486A-486B; (ii) CAN/CSA-C22.2 No. 188 or UL 486C; or (iii) UL 486E; (h) devices, such as quick-connect terminals, that are covered by CSA C22.2 No. 153 or UL 310; (i) devices covered by CSA C22.2 No. 182.3 or UL 1977; and (j) devices, such as pin and sleeve connectors, that are covered by CSA C22.2 No. 182.1 or UL 1682.

Insulated multi-pole splicing wire connectors

UL 231-2008 电源插座

1.1 These requirements cover power outlets, with or without integral mounting posts or pedestals, and power outlet fittings for use in accordance with the National Electrical Code, NFPA 70. 1.2 A power outlet covered by these requirements, although not restricted to such use, is intended for use: a) At outdoor locations such as on farms, at building sites, and the like, where power is required to operate portable, mobile, or temporarily installed equipment, b) To supply power to a mobile home or a recreational vehicle, and c) To supply shore power to boats. 1.3 A power outlet may contain: a) Attachment plug receptacles, b) Circuit breakers, c) Fuseholders, d) Fused switches and facilities for watt-hour meters, and e) Provisions for field installed circuit breakers or switches and fuses. 1.4 Power outlet fittings covered by these requirements are intended for factory or field assembly into or in conjunction with power outlets designed for such assembly. Fittings may be panels or combination units incorporating receptacles, disconnecting means, overcurrent protection or other devices that have been determined to be equivalent. A separable mounting post or pedestal to which power outlets are to be mounted is also a fitting. 1.5 In addition to or instead of mounting to a post or pedestal fitting as mentioned in 1.4, a power outlet may be constructed for mounting on and connection to a mounting post or pedestal also designed to be used with other types of distribution equipment. 1.6 Some power outlets may have special features and markings to indicate their acceptability for use as service equipment. 1.7 A power outlet with a mounting post is intended for mounting in concrete. A power outlet with a mounting pedestal is intended for mounting on a concrete slab. Unless marked otherwise, a mounting post or pedestal fitting is not intended to serve as the sole support of a mast for overhead wiring.

Power outlets

NF C15-100/A1:2008 低音张力装置

Installations électriques à basse tension