K30 低压电器综合 标准查询与下载

DIN EN 60309-4:2008 工业用插头、插座和连接器.第4部分:有或没有互锁的开关插座和连接器

Plugs, socket-outlets and couplers for industrial purposes - Part 4: Switched socket-outlets and connectors with or without interlock (IEC 60309-4:2006, modified); German version EN 60309-4:2007

BS IEC 61892-7:2007 移动、固定式近海装置.电气装置.危险区域

This part of IEC 61892 contains provisions for hazardous areas classification and choice of electrical installation in hazardous areas in mobile and fixed offshore units, including pipeline, pumping or 'pigging' stations, compressor stations and exposed location single buoy moorings, used in the offshore petroleum industry for drilling, processing and for storage purposes. It applies to all installations, whether permanent, temporary, transportable or hand-held, to a.c. installations up to and including 35 000 V and d.c. installations up to and including 750 V.(a.c. and d.c. voltages are nominal values). This standard does not apply to electrical installations in rooms used for medical purposes, or in tankers.

Mobile and fixed offshore units - Electrical installations - Hazardous areas

SANS 1973-3:2008 低压开关及控制设备总成.第3部分:额定预期短路电流小于或等于10 kA总成的安全

Applies to low-voltage switchgear and controlgear ASSEMBLIES that have a rated prospective short-circuit current of up to and including 10 kA, are stationary or movable, that have a rated voltage not exceeding 1 000 V a.c. at frequencies not exceeding 50

Low-voltage switchgear and controlgear ASSEMBLIES Part 3: Safety of ASSEMBLIES with a rated prospective short-circuit current of up to and including 10 kA

SANS 1973-8:2008 低压开关及控制设备总成.第8部分:与额定短路电流超过10 kA及额定母线电流小于或达到1600 A交流与直流的最小测试总成(MTA)的安全

Applicable to low-voltage switchgear and controlgear assemblies that are subjected to minimum tests for verifying the safety of the ASSEMBLY; that have a rated prospective short-circuit current above 10 kA and a rated busbar current of up to and includin

Low-voltage switchgear and controlgear ASSEMBLIES Part 8: Safety of minimally tested ASSEMBLIES (MTA) with a rated short-circuit current above 10 kA and a rated busbar current of up to and including 1 600 A a.c. and d.c.

NF C61-314:2008 家用和类似用途的插头和电源插座.6A/250V和16A/250V设备

Plugs and socket-outlets for household and similar purposes - 6 A / 250 V and 16 A / 250 V systems.

JB/T 2924-2008 机床电器产品型号编制方法

本标准规定了机床电器及其派生系列产品型号的编制方法。 本标准适用于机床电器及其派生系列产品型号的编制和注册。 机床电器包括： a)接触器； b)起动器； c)断路器； d)熔断器； e)热继电器； f)时间继电器； g)中间继电器； h)继电器； i)行程开关； j)接近开关； k)按钮开关； 1)主令开关； m)转换开关； n)自动转换开关； o)插头插座； p)信号灯； q)牵引电磁铁； r)阀用电磁铁； s)机械设备用变压器； t)电磁离合器； u)电磁制动器； v)电连接器； w)可编程序控制器； x)其他。

Identification and registration methods for machine tool electrical apparatus

DIN EN 60947-1 Bb.1:2008 低压开关装置和控制装置.过电流保护装置.第1部分:短路额定值的应用

Low-voltage switchgear and controlgear - Overcurrent protective devices - Part 1: Application of short-circuit ratings (IEC/TR 61912-1:2007)

BS EN 60947-5-9:2007 低压开关装置和控制器.第5-9部分:控制电路装置和开关元件.流量率开关

This part of IEC 60947 applies to flow rate switches that sense the rate of flow of a gas, a liquid or a granular solid. These switches change their output state if a pre-set value for the speed of flow is exceeded. These flow rate switches are self-contained, have semiconductor switching element(s) and are intended to be connected to circuits, the rated voltage of which does not exceed 250 V 50 Hz/60 Hz a.c. or 300 V d.c. This standard does not specify the additional measures that are necessary for flow rate switches used in conjunction with explosive sensing materials and/or in an explosive location. This standard is not intended to cover devices with analogue outputs. The object of this standard is to state for flow rate switches: – definitions; – classifications; – characteristics; – product information; – normal service, mounting and transport conditions; – constructional and performance requirements; – tests to verify rated characteristics

Low-voltage switchgear and controlgear. Part 5-9: Control circuit devices and switching elements. Flow rate switches

NF C20-040-5:2008 低压系统内设备的绝缘配合.第5部分:间隙距离和漏电距离小于或等于2mm的测定用综合方法

Insulation coordination for equipment within low-voltage systems - Part 5 : comprehensive method for determining clearances and creepage distances equal to or less than 2 mm.

NF C64-471-209:2008 高压开关装置和控制器.第209部分:额定电压高于52kV的气体绝缘金属外壳开关装置用电缆连接件.充流体和挤压绝缘电缆.充流体和干型电缆终端

High-voltage switchgear and controlgear - Partie 209 : cable connections for gas-insulated metal-enclosed switchgear for rated voltages above 52 kV - Fluid-filled and extruded insulation cables - Fluid-filled and dry type cable-terminations.

IEC TR 61641:2008 封闭式低压成套开关设备和控制设备在内部故障引起电弧情况下的试验导则

This technical report applies to enclosed low-voltage switchgear and controlgear assemblies - hereafter called ASSEMBLIES - manufactured according to IEC 60439-1. The purpose of this technical report is to give guidance on the method of testing of enclosed low-voltage switchgear and controlgear assemblies under conditions of arcing in air due to an internal fault. The purpose of this test is to assess the ability of the ASSEMBLY to limit the risk of personal injury and damage of ASSEMBLIES resulting from an internal arcing fault. This is a voluntary test made either at the discretion of the manufacturer, or subject to an agreement between manufacturer and user. NOTE The recommendations of this report are not acceptable in the USA, nor in Canada, nor in the United Kingdom.

Enclosed low-voltage switchgear and controlgear assemblies - Guide for testing under conditions of arcing due to internal fault

IEC 62026-3:2008 低压开关设备和控制设备.控制器-器件的接口(CDIs).第3部分:器件网络

This part of IEC 62026 specifies an interface system between single or multiple controllers, and control circuit devices or switching elements. The interface system uses two twisted shielded conductor pairs within one cable – one of these pairs provides a differential communication medium and the other pair provides power to the devices. This part establishes requirements for the interchangeability of components with such interfaces. This part of IEC 62026 specifies the following particular requirements for DeviceNet: ? requirements for interfaces between controllers and switching elements; ? normal service conditions for devices; ? constructional and performance requirements; tests to verify conformance to requirements. These particular requirements apply in addition to the general requirements of IEC 62026-1.

Low-voltage switchgear and controlgear - Controller-device interfaces (CDIs) - Part 3: DeviceNet

IEC 62026-2:2008 低压开关装置和控制装置.控制器-器件的接口(CDIs) 第2部分:操动件敏感元件接口(AS-i)

This part of IEC 62026 specifies a method for communication between a single control device and switching elements, and establishes a system for the interoperability of components with the specified communication interfaces. The complete system is called “Actuator Sensor interface (AS-i)”. This standard describes a method for connecting switching elements, such as low-voltage switchgear and controlgear, standardized within IEC 60947, and controlling devices. The method may also be applied for connecting other devices and elements. Where inputs and outputs I/O are described in this standard, their meaning is regarding the master, the meaning regarding the application is the opposite.

Low-voltage switchgear and controlgear - Controller-device interfaces (CDIs) - Part 2: Actuator sensor interface (AS-i)

DIN EN 60664-1:2008 低压系统内设备的绝缘配合.第1部分:原理、要求和试验

Insulation coordination for equipment within low-voltage systems - Part 1: Principles, requirements and tests (IEC 60664-1:2007); German version EN 60664-1:2007

ANSI/SCTE 155-2008 室内"F"插座到"F"插座内线接合

The purpose of this document is to recommend mechanical and electrical standards for 75 Ohm broadband radio frequency (RF) devices. Whose purpose is to provide an indoor inline connection between two type "F" male connectors that conform to ANSI/SCTE 123 2006; Specification for "F" Connector, Male, Feed- Through or ANSI/SCTE 124 2006; Specification for "F" Connector, Male, Pin Type. The mechanical configuration is designed to accommodate wall plate and bulkhead applications.

Indoor "F" Female to "F" Female Inline Splice

ANSI/EIA 364-60A:2008 电连接器和插座用触点抛光材料孔隙率测试的一般方法

This test procedure details the methods for determining the porosity of contact finishes used in electrical connector, contacts and sockets.

General Methods for Porosity Testing of Contact Finishes for Electrical Connectors and Sockets

ANSI/SCTE 148-2008 75欧姆"F"插头终端器用规范

The purpose of this specification is to specify requirements of the Male 'F' Terminators that are used on 'F' ports as specified in ANSI/SCTE 01 2006 and ANSI/SCTE 02 2006. This specification in no way should limit or restrict any manufacturers from innovative designs and product improvements.

Specification for Male "F" Terminator, 75 ohm

JIS C 8201-4-1:2007 低压开关装置和控制装置.第4部分:接触器和电机启动器.第1节:电动机械接触器和电机启动器

この規格は，1.1及び1.2に規定した定格電圧が，交流1 000 V又は直流1 500 V以下の回路に接続する主接点をもつ装置類に適用する。

Low-voltage switchgear and controlgear -- Part 4: Contactors and motor-starters -- Section 1: Electromechanical contactors and motor-starters

JIS C 8201-5-1:2007 低压开关装置和控制装置.第5-1部分:控制电路器件和开关元件.机电控制电路器件

この規格は，開閉制御装置の，制御，信号，インターロックなどを意図する制御回路機器及び開閉素子に適用する。

Low-voltage switchgear and controlgear -- Part 5-1: Control circuit devices and switching elements -- Electromechanical control circuit devices

JIS C 8201-1:2007 低压开关装置和控制装置.第1部分:一般规则

この規格は，交流1000V以下又は直流1500V以下の定格電圧で，かつ，これらの回路に接続し，規格本文中に“装置(equipment)”として規定する開閉装置及び制御装置の通則的事項について規定する。

Low-voltage switchgear and controlgear -- Part 1: General rules