K32 控制电器 标准查询与下载

JB/T 5553-2006 行程开关

本标准规定了行程开关的型式、参数、技术要求、试验方法、检验规则等。 本标准适用于在交流50Hz或60Hz、电压至380V，直流电压至220V的控制电路或辅助电路中，作控制、限位、定位、行程、信号或程序转换之用的行程开关。

Limit switches

IEC 60439-5:2006 低压开关设备和控制设备组件.第5部分:公共网上电力分配用组件的特殊要求

公用电网动力配电变电站电缆配电盘(SCDBs)和电缆分线箱(CDCs)应符合GB 7251．1 2005的要求，并应遵守本部分的特殊要求。 本部分给出了变电站电缆配电盘(SCDBs)和电缆分线箱(CDCs)的补充要求，此装置为固定安装的型式试验的成套设备(TTA)，用于三相系统的电能分配。本部分不包括开启式成套设备。 符合其他标准的单独部件，例如熔断器和开关器件也应符合本部分的要求。 本部分规定了变电站电缆配电盘和电缆分线箱的定义、工作条件、结构要求、技术性能和试验要求。对特殊电网，例如，环网连接，可以要求较高的性能和试验水平。 注1：如果电缆分线箱配备的附加设备(例如仪表)明显的改变了其主要功能，可以根据制造商和用户之间的协议采用其他的标准(见7．6)。 注2：如果地方法规和实际情况允许，符合本部分的变电站电缆配电盘或电缆分线箱亦可用于公用配电网以外的其他配电网上。 变电站电缆配电盘适于安装在只有专业人员可以进入的场地，户外式变电站电缆配电盘安装在公众可以接近的场地。 变电站电缆配电盘是采用连接线、汇流排或电缆将其连接在配电变压器的低压端上。 安装在公众可进入场地的户外式电缆分线箱，只有专业人员在使用时才能接近。

Low-voltage switchgear and controlgear assemblies - Part 5: Particular requirements for assemblies for power distribution in public networks

JB/T 8591.3-2006 CJ40系列交流接触器

JB/T8591的本部分规定了CJ40系列交流接触器（以下简称“接触器”）的基本要求，包括：术语、特性、正常工作和安装条件、结构和性能要求、试验项目及试验方法等。 接触器主要用于交流50Hz（或60Hz）、额定电压至1140V，电流至1000A的电力系统中接通和分断电路，并与适当的热继电器或电子保护器组合成电动机起动器，以保护可能发生过载的电路。

CJ40 Series AC contactors

IEC 60947-2:2006 低压开关和控制设备.第2部分:断路器

This standard applies to circuit-breakers, the main contacts of which are intended to be connected to circuits, the rated voltage of which does not exceed 1 000 V a.c. or 1 500 V d.c.; it also contains additional requirements for integrally fused circuit-breakers. It applies whatever the rated currents, the method of construction or the proposed applications of the circuit-breakers may be. The requirements for circuit-breakers which are also intended to provide earth-leakage protection are contained in Annex B. The additional requirements for circuit-breakers with electronic over-current protection are contained in Annex F. The additional requirements for circuit-breakers for IT systems are contained in Annex H. The requirements and test methods for electromagnetic compatibility of circuit-breakers are contained in Annex J. The requirements for circuit-breakers not fulfilling the requirements for over-current protection are contained in Annex L. The requirements for modular residual current devices (without integral current breaking device) are contained in Annex M. The requirements and test methods for electromagnetic compatibility of circuit-breaker auxiliaries are contained in Annex N. Supplementary requirements for circuit-breakers used as direct-on-line starters are given in IEC 60947-4-1, applicable to low-voltage contactors and starters. The requirements for circuit-breakers for the protection of wiring installations in buildings and similar applications, and designed for use by uninstructed persons, are contained in IEC 60898. The requirements for circuit-breakers for equipment (for example electrical appliances) are contained in IEC 60934. For certain specific applications (for example traction, rolling mills, marine service) particular or additional requirements may be necessary. NOTE Circuit-breakers which are dealt with in this standard may be provided with devices for automatic opening under predetermined conditions other than those of over-current and undervoltage as, for example, reversal of power or current. This standard does not deal with the verification of operation under such pre-determined conditions. The object of this standard is to state: a) the characteristics of circuit-breakers; b) the conditions with which circuit-breakers shall comply with reference to: 1) operation and behaviour in normal service; 2) operation and behaviour in case of overload and operation and behaviour in case of short-circuit, including co-ordination in service (discrimination and back-up protection); 3) dielectric properties; c) tests intended for confirming that these conditions have been met and the methods to be adopted for these tests; d) information to be marked on or given with the apparatus.

Low-voltage switchgear and controlgear - Part 2: Circuit-breakers

CSA E61131-2-06-CAN/CSA-2006 可编程设计的控制器.第2部分:设备要求及测试.第1版.IEC 61131-2:2003

Programmable controllers ?Part 2: Equipment requirements and tests First Edition; IEC 61131-2:2003

Programmable controllers ?Part 2: Equipment requirements and tests First Edition

JB/T 10522-2005 小容量交流接触器可靠性试验方法

本标准规定了小容量交流接触器(以下简称接触器)的可靠性验证试验的一般要求和方法，包括接触器的可靠性等级要求、试验方法、试验方案及试验程序等。 本标准适用于交流5OHz或60Hz，主电路额定工作电流50A及以下，额定控制电源电压从24V至400V，其寿命能合理地认为是服从指数分布的交流接触器(以下简称接触器)的可靠性验证试验。主电路额定工作电流50A以上的接触器的可靠性验证试验也可参照本标准进行。

Reliability test method for lower capacity alternating current contactors

JIS C 0704 ERRATUM 1:2005 勘误

ERRATUM

IEC TR 61131-8:2003 可编程控制器 第8部分：编程语言的应用和实施指南（2.0 版）

This part of IEC 61131@ which is a technical report@ applies to the programming of programmable controller systems using the programming languages defined in IEC 61131-3. It also provides guidelines for the implementation of these languages in programmable controller systems and their programming support environments (PSEs).IEC 61131-4 should be consulted for other aspects of the application of programmable controller systems.NOTE Neither IEC 61131-3 nor this technical report explicitly addresses safety issues of programmable controller systems or their associated software. The various parts of IEC 61508 should be consulted for such considerations.

Programmable Controllers - Part 8: Guidelines for the Application and Implementation of Programming Languages (Edition 2.0)

UL 244A-2003 设备的固态控制装置

1.1 These requirements cover component electronic controls intended to be factory installed on or in appliances and other utilization equipment rated 600 V or less, used in ordinary dry locations as defined in the National Electrical Code, NFPA 70, and that comply with the requirements for such appliances and equipment. 1.2 For a control covered by this standard, it is assumed that: a) No voltage greater than 600 V above ground will be present in a control, b) An isolation transformer, if provided, will generally furnish power at a lower potential than the primary voltage, and c) The output of the control will not be located in a circuit operating at greater than 600 V above ground in the end-use product. If conditions other than these are provided, consideration shall be given to the need for additional requirements.

UL Standard for Safety Solid-State Controls for Appliances

IEC 61131-2:2003 程序控制器.第2部分:设备要求和试验

Specifies requirements and related tests for programmable controllers (PLC) and their associated peripherals (for example, programming and debugging tools (PADTs), human-machine interfaces (HMIs), etc.) which have as their intended use the control and co

Programmable controllers - Part 2: Equipment requirements and tests

IEC 61131-3:2003 程序控制器.第3部分:程序设计语言

This part of IEC 61131 specifies syntax and semantics of programming languages for programmable controllers as defined in part 1 of IEC 61131.

Programmable controllers - Part 3: Programming languages

JB/T 10386-2002 家用和类似用途空调电子膨胀阀

本标准规定了家用和类似用途空调电子膨胀的术语和定义、型号、要求、试验方法、检验规则及标志、包装、运输和贮存。 　　本标准适用于额定电压不大于36V、阀口径不大于4mm、以R22为制冷剂的直动式电子膨胀阀。以R407C、R410A等为制冷剂的电子膨胀阀可参照执行。

Electronic expansion valve for household and similar air conditioner

JB/T 6317-2002 船用机电式控制电路电器

本标准规定了船用机电式控制电路电器的定义、符号、代号、分类、正常使用和安装条件、结构和性能要求、试验方法、检验规则以及标志、包装、运输和贮存要求。 本标准适用于船用开关设备和控制设备中作控制、信号、联锁等用途的控制开关。 本标准适用于额定电压不超过交流500V(频率不超过1000Hz)或直流600V的控制开关; 本标准一般不推荐用于工作电压小于交流或直流100V的控制开关。

Electromechanical control circuit devices in ships

JB/T 10385-2002 家用和类似用途手动复位压力式热切断器

本标准规定了家用和类似用途手动复位压力式热切断器的定义、型号与基本参数、技术要求、试验方法、检验规则和标志、使用说明书、包装、运输及贮存。 　　本标准适用于以密闭系统内的工质受热产生压力推动突跳式执行机构，使电器触点断开为工作原理的限温器件。该限温器件一般用于交流额定电压不大于250V、额定电流不大于32A、频率50Hz或60Hz、切断温度80℃～200℃内任一确定值、电阻性负载电能加热、要求对整机全极断开保护的热水器、开水器、滚筒洗衣机等家用及类似用途电器。

Pressure thermal cut-outs for household and similar use of manual reset type

JB/T 5791-2002 船用组合开关

　　本标准规定了船用组合开关的型号、规格、标志、正常工作条件、技术要求、试验、包装、运输及贮存。 　本标准适用于HZ9lO系列船用组合开关，该开关安装在船舶上，作交流50Hz(或60Hz)、380V及以下，直流220V及以下的电气线路中供手动不频繁接通或分断电路和换接电路之用，一般不能直接起动电动机和切断短路电流，仅10A、25A等开关可控制小容量电动机。 注：交流440V、660V开关可参照本标准执行，有关性能要求由制造厂和用户协商确定。

Rotary switch for ship

CSA E60730-1-02-CAN/CSA-2002 家用和类似用途的电器自动控制器-第1部分:通用要求.第3版

Automatic Electrical Controls for Household and Similar Use - Part 1: General Requirements Third Edition

Dispositifs De Commande Electrique Automatiques a Usage Domestique Et Analogue - Partie 1: Regles Generales Troisieme Edition

BS EN 50344-1:2002 EN 60730规定的控制的例行试验.一般要求

Details line tests carried out by manufacturer and performed on 100% of production, normally at the final stage of manufacture

Routine tests for controls within the scope of the EN 60730 series - General requirements

DL/T 780-2001 配电系统中性点接地电阻器

本标准规定了配电系统中中性点接地电阻器(以下简称电阻器)的技术性能、型式试验和出厂试验以及标志、包装和贮运的要求。 本标准适用于电力系统标称交流电压50Hz、35kV及以下的空气自冷式金属材料接地电阻器。

Specification for neutral-to-earth resistance in distrbution system

BS EN 60320-1:2001 家用和类似用途设备耦合器.一般要求

This part of IEC 60320 is applicable to two-pole appliance couplers for a.c. only, with or without earthing contact, with a rated voltage not exceeding 250 V and a rated current not exceeding 16 A, for household and similar general purposes and intended for the connection of a supply cord to electrical appliances or other electrical equipment for 50 Hz or 60 Hz supply. NOTE 1 Appliance inlets integrated or incorporated in appliances or other equipment are within the scope of this standard. The dimensional and general requirements of this standard apply to such inlets, but certain tests may not be relevant. NOTE 2 The requirements for connectors are based on the assumption that the temperature of the pins of the corresponding appliance inlets does not exceed 70 ℃ for connectors for cold conditions; 120 ℃ for connectors for hot conditions; 155 ℃ for connectors for very hot conditions. NOTE 3 Appliance couplers complying with this standard are suitable for use at ambient temperatures not normally exceeding 25 ℃, but occasionally reaching 35 ℃. NOTE 4 Appliance couplers complying with the standard sheets in this standard are intended for the connection of equipment having no special protection against moisture. If appliance couplers are used with equipment which may be subject to spillage of liquid in normal use then protection against moisture is to be provided by the equipment. NOTE 5 Special constructions may be required - in locations where special conditions prevail, for example, as in ships, vehicles and the like; - in hazardous locations, for example, where explosions are liable to occur.

Appliance couplers for household and similar general purposes - General requirements

BS EN 60320-2-1:2001 家用和类似通用用途的器具耦合器 个别类型耦合器的要求规范 缝纫机耦合器

The couplers are for a.c. only and have a rated voltage not exceeding 250 V and a rated current not exceeding 2.5 A. To be read in conjunction with BS EN 60320-1:1996

Appliance couplers for household and similar general purposes. Specification of requirements for individual types of coupler. Sewing machine couplers