K40 输变电设备综合 标准查询与下载

NF C78-200:1993 电栅网增能器.交流供电的电栅网的增能器安全要求(IEC101-89.修订)

Electric fence energizers. Safety requirements for mains-operated electric fence energizers.

KS C 1616-1992 金属铠装温度计电阻传感器

This Korean Industrial Standard specifies the sheathed platinum resistance thermometer sensors to be used for temperature measurements, hereinafter referred to as the "sheathed resistance thermometer sensors", whose resistance value at 0°C is 100Ω. Remark Normative references to this standard shall be as follows. KS A 0006 Standard Atmospheric Conditions for Testing KS A 0511 Temperature Measurements—General requirements Corresponding International Standard : KS B 5202 Micrometer Callipers for External Measurement KS C 1302 Insulation Resistance Testers(Battery Operated) KS C 1606 Electrical Methods of Temperature Measurements

Metal sheathed resistance thermometer sensors

prEN 50107-1992 用于1000V以上无负载输出电压工作的符号和气体放电管设备的操作

Signs and luminous-discharge-tube installations operating from a no-load output voltage exceeding 1000 V

NAVY MIL-F-22606 C-1992 空气,氧气和氮压缩空气和端塞烧瓶

FLASK, COMPRESSED GAS, AND END PLUGS FOR AIR, OXYGEN, AND NITROGEN

FLASK, COMPRESSED GAS, AND END PLUGS FOR AIR, OXYGEN, AND NITROGEN

IEC 60060-1/COR1:1992 高压试验技术.第1部分:一般定义和试验要求.技术勘误1

This standard is High-voltage test techniques - Part 1: General definitions and test requirements; Corrigendum 1.

High-voltage test techniques - Part 1: General definitions and test requirements; Corrigendum 1

CSA C22.2 No.0.16-M92-CAN/CSA-1992 谐波电流测量.通用指令第1号

It has been found that harmonic currents appearing in the neutral conductor of a 3-phase, 4-wire supply system can exceed the rated phase current with consequent overheating. This situation could lead to a fire hazard. The likelihood of this occurring i

Measurement of Harmonic Currents General Instruction No 1-2

DL 417-1991 电力设备局部放电现场测量导则

Guidelines for On-site Measurement of Partial Discharge of Power Equipment

KS C 1615-1991 金属铠装热电偶

이 규격은 온도 측정에 사용하는 시스 열전대에 대하여 규정한다.

Metal sheathed thermocouples

JB/T 5871-1991 交流高压断路器的线路充电电流开合试验

Line charging current switching test of AC high voltage circuit breaker

DL/T 437-1991 高压直流接地极技术导则

Technical guidelines for high voltage direct current buried electrode

HD 588.1 S1-1991 高压试验技术.第1部分:一般定义和试验要求(IEC 60-1-89+Corrigendum-90)

High-voltage test techniques; part 1: general definitions and test requirements (IEC 60-1:1989 + corrigendum March 1990)

NAVY MIL-S-24186 B VALID NOTICE 1-1991 HD-732/UD型空气中粒子采样器

MIL-S-24186B(EC), dated 14 July 1986 has been reviewed and determined to be valid-for use in acquisition.

SAMPLER, AIR PARTICLE, HD-732/UD

NAVY MIL-G-17489 B VALID NOTICE 1-1991 锅炉压力(空气)计

MIL-G-l7489B(SHIPS), dated 15 March 1961, has been reviewed and determined to be valid for use in acquisition.

GAGES, PRESSURE (AIR), BOILER

NAVY MIL-I-24490 B VALID NOTICE 1-1991 MARK 5,MOD 2(15人)和MARK 6(25人)可充气的压缩空气膨胀系统设备

MIL-I-24490B, dated 21 April 1981, and Amendment 1 dated 03 October 1985, has been reviewed and determined to be valid for use in acquisition.

INFLATION SYSTEM EQUIPMENT, COMPRESSED AIR, FOR MARK 5, MOD 2 (15 PERSON) AND MARK 6 (25-PERSON) INFLATABLE LIFEBOATS

IEC TR 60919-2:1991 高压直流(HVDC)系统性能.第2部分:故障和操作

GB/Z 20996的本部分是关于高压直流系统暂态性能和故障保护要求的指导性技术文件。论述了 三相桥式(双路)联结的12脉波(动)换流单元构成的两端高压直流系统故障及操作的暂态性能。不涉 及多端高压直流输电系统，但对包含在两端系统内的并联换流器和并联线路作了讨论。假定换流器使 用晶闸管阀作为桥臂，采用无间隙金属氧化物避雷器进行绝缘配合，且功率能够双向传输。本部分没有 考虑二极管阀。 GB/Z 20996由三个部分组成。第1部分稳态，第2部分故障和操作，第3部分动态。在制定与编 写过程中，已经尽量避免了三部分内容重复。因此，当使用者准备编制两端高压直流系统规范时，应参 考三个部分的全部内容。 对系统中的各个部件，应注意系统性能规范与设备设计规范之间的差别。本部分没有规定设备技 术条件和试验要求，而是着重于那些影响系统性能的技术要求。本部分也没有包括详细的地震性能要 求。另外，不同的高压直流系统可能存在许多不同之处，本部分也没有对此详细讨论，因此，本部分不应 直接用作某个具体工程项目的技术规范。但是，可以以此为基础为具体的输电系统编制出满足实际系 统要求的技术规范。本部分涉及的内容没有区分用户和制造厂的责任。

Performance of high-voltage d.c. (HVDC) systems; part 2: faults and switching

NAVY A-A-50431 A-1991 空气软管及管道弓形迅速分离接合器

Purchaser should specify class and size of coupling halves or fittings required.

COUPLINGS - QUICK DISCONNECT, BOWES TYPE (AIR HOSES AND PIPING)

ANSI/IEEE 393:1991 磁芯试验程序

Specifies applicable tests to describe the significant properties of magnetic cores used in electronic applications. It is primarily concerned with magnetic cores of the type used in electronics transformers, magnetic amplifiers, inductors, and related devices. However, many of the tests specified herein are general in scope and adaptable to magnetic cores used in many other applications. Standards covered by this publication include tests for specifying or measuring, or both, permeability, core loss, apparent core, induction, hysteresis, thermal characteristics, and other properties of all commonly used types of magnetic cores.

Magnetic Cores, Test Procedures for

BS 923-1:1990 高压试验技术导则.第1部分:总则

Defines test requirements for dielectric tests with direct voltages, alternating voltages and impulse voltages and tests with impulse current. Applicable only to tests on equipment having its highest voltage greater than 1 kV. It is not intended to be used for electromagnetic compatibility tests on electric or electronic equipment.

Guide on high-voltage testing techniques - General

DIN 43455:1990 52KV以下高压开关装置操作图形符号

This standard specifices graphical symbols for operating the driving mechanism of disconnectors and earthing switches according to DIN VDE 0670 part 2, mechanical switches according to DIN VDE 0670 part 301 (at present in draft form) and circuit-breakers according to DIN VDE 0670 part 101 to part 108. The purpose of this standard is the uniform use for graphical symbols for the operation of switchgear.#,,#

Graphical symbols for operation of high-voltage switchgear less than 52 kV

NAVY MIL-R-23074 C-1990 橡胶-空气-铅型(铝回收率)橡胶砖

This specification covers rubber tile used for reducing the transmission of vibration from metal plates to water.

RUBBER TILE, RUBBER-AIR-LEAD-TYPE (RAL)