K48 绝缘子 标准查询与下载

DIN EN 61462:2008 复合空心绝缘子.使用在额定电压大于1000伏的电气设备用受压和未受压绝缘子.定义、试验方法、验收标准和设计建议

Composite hollow insulators - Pressurized and unpressurized insulators for use in electrical equipment with rated voltage greater than 1000 V - Definitions, test methods, acceptance criteria and design recommendations (IEC 61462:2007); German version EN 6

IEC TS 62371:2008 额定电压大于1000V的电气设备用空心增压和未增压陶瓷、玻璃绝缘子的特性

This Technical Specification applies to - ceramic and glass hollow insulators intended for general use in electrical equipment; - ceramic hollow insulators intended for use with a permanent gas pressure in switchgear and controlgear. They are intended for indoor and outdoor use in electrical equipment, operating on alternating current with a rated voltage greater than 1 000 V and a frequency not greater than 100 Hz or for use in direct current equipment with a rated voltage greater than 1 500 V. This specification specifies the dimensional and mechanical characteristics of the hollow insulator, which are essential for interchangeability of the hollow insulator of the same type. It is not the object of this specification to prescribe electrical characteristics because they are dependent on the apparatus of which the hollow insulator ultimately forms a part. However, standard lightning impulse withstand voltage which is provided in IEC 60071-1 is described only for reference for classification purpose. This specification applies to hollow insulators for use in electrical equipment in clean areas or lightly polluted areas, where seismic qualification is not required. For use in areas characterised by heavy pollution levels and for other particular or extreme environmental conditions such as seismic force, it may be necessary for certain dimensions to be changed. The hollow insulators covered by this specification are: a) straight type hollow insulators with metal fittings on both ends; b) taper type hollow insulators with metal fittings on both ends; c) straight type hollow insulators without metal fittings; d) taper type hollow insulators without metal fittings. The hollow insulators are intended for use in electrical equipment, for example: - circuit-breakers; - instrument transformers; - surge arresters; - bushings; - cable sealing ends; - switch-disconnectors; - disconnectors; - earthing switches; - capacitors. There may be some cases that hollow insulators whose design can strongly be influenced by other components of specific equipment, for example, active parts of circuit-breakers. For such cases, the hollow insulators can be separately designed, depending on respective requirements of such equipment and not be covered by this specification. NOTE 1 Hollow insulators not prescribed in this specification can also be applied to electrical equipment, depending on specific requirements of the equipment. However, if similar insulators are available in this specification, it is preferable to apply them. NOTE 2 For general recommendations for design and tests of the hollow insulators, see IEC 62155 NOTE 3 For characteristics of hollow insulators for use in polluted areas, reference can be made to IEC 60815- 1and IEC 60815-2.

Characteristics of hollow pressurised and unpressurised ceramic and glass insulators for use in electrical equipment with rated voltages greater than 1000 V

IEC 61109:2008 架空线路用绝缘子.标称电压大于1000V的交流架空线路用复合绝缘子和耐张绝缘子.定义、试验方法和验收准则

This International Standard applies to composite suspension/tension insulators consisting of a load-bearing cylindrical insulating solid core consisting of fibres - usually glass - in a resin- based matrix, a housing (outside the insulating core) made of polymeric material and end fittings permanently attached to the insulating core. Composite insulators covered by this standard are intended for use as suspension/tension line insulators, but it should be noted that these insulators can occasionally be subjected to compression or bending, for example when used as phase-spacers. This standard can be applied in part to hybrid composite insulators where the core is made of a homogeneous material (porcelain, resin), see Clause 8. The object of this standard is to - define the terms used, - prescribe test methods, - prescribe acceptance criteria. This standard does not include requirements dealing with the choice of insulators for specific operating conditions.

Insulators for overhead lines - Composite suspension and tension insulators for a.c. systems with a nominal voltage greater than 1000 V - Definitions, test methods and acceptance criteria

IEC 61952:2008 架空线路用绝缘子.标称电压大于1000V的交流架空线路用复合线路柱形绝缘子

This International Standard applies to composite line post insulators consisting of a load- bearing cylindrical insulating solid core consisting of fibres - usually glass - in a resin-based matrix, a housing (outside the insulating core) made of polymeric material and end fittings permanently attached to the insulating core. Composite line post insulators covered by this standard are subjected to cantilever, tensile and compressive loads, when supporting the line conductors. They are intended for use on a.c. overhead lines with a rated voltage greater than 1 000 V and a frequency not greater than 100 Hz. The object of this standard is - to define the terms used, - to prescribe test methods, - to prescribe acceptance or failure criteria. This standard does not include requirements dealing with the choice of insulators for specific operating conditions.

Insulators for overhead lines - Composite line post insulators for a.c. systems with a nominal voltage greater than 1000 V - Definitions, test methods and acceptance criteria

GOST R 52034-2008 陶瓷支撑绝缘子电压超过1000 V.一般规范

Ceramic support insulators for voltage over 1000 V. General specifications

BS EN 61462:2007 复合空心绝缘子.额定电压大于1000 V的电气设备用受压和未受压绝缘子.定义、试验方法、验收标准和设计建议

This International Standard applies to composite hollow insulators consisting of a load-bearing insulating tube made of resin impregnated fibres, a housing (outside the insulating tube) made of elastomeric material (for example silicone or ethylene-propylene) and metal fixing devices at the ends of the insulating tube. Composite hollow insulators as defined in this standard are intended for general use (unpressurized) or for use with a permanent gas pressure (pressurized). They are intended for use in both outdoor and indoor electrical equipment operating on alternating current with a rated voltage greater than 1 000 V and a frequency not greater than 100 Hz or for use in direct current equipment with a rated voltage greater than 1 500 V. This standard does not prescribe impulse voltage or power frequency voltage type tests, nor does it prescribe pollution tests because the withstand voltages are not characteristics of the hollow insulator itself, but of the apparatus of which it ultimately forms a part. All the tests in this standard, apart from the thermal-mechanical test, are performed at normal ambient temperature. This standard does not prescribe tests that may be characteristic of the apparatus of which the hollow insulator ultimately forms a part. Further technical input is required in this area.

Composite hollow insulators - Pressurized and unpressurized insulators for use in electrical equipment with rated voltage greater than 1000 V. Definitions, test methods, acceptance criteria and design recommendations

IEC 61466-1:1997/COR1:2007 额定电压超过1000V的架空线路用复合绝缘子串组合件.第1部分:标准强度等级和终端部件.技术勘误1

This standard is about Composite string insulator units for overhead lines with a nominal voltage greater than 1000 V - Part 1: Standard strength classes and end fittings; Corrigendum 1

Composite string insulator units for overhead lines with a nominal voltage greater than 1000 V - Part 1: Standard strength classes and end fittings; Corrigendum 1

IEC 36C/172/DTS:2007 IEC/TS 62371, Ed. 1.0:额定电压超过1000V的电气设备用空心压力和非压力陶瓷和玻璃绝缘子的特征

IEC/TS 62371, Ed. 1.0: Characteristics of hollow pressurised and unpressurised ceramic and glass insulators for use in electrical equipment with rated voltages greater than 1000 V

SANS 61462:2007 复合空心绝缘子．使用在额定电压大于1000伏的电气设备用受压和未受压绝缘子．定义、试验方法、验收标准和设计建议

Applies to composite hollow insulators consisting of a load-bearing insulating tube made of resin impregnated fibres, a housing (outside the insulating tube) made of elastomeric material (for example silicone or ethylene-propylene) and metal fixing devic

Composite hollow insulators - Pressurized and unpressurized insulators for use in electrical equipment with rated voltage greater than 1 000 V - Definitions, test methods, acceptance criteria and design recommendations

NF C01-471:2007 国际电工词汇.第471部分:绝缘子

International Electrotechnical Vocabulary - Part 471 : insulators.

DIN EN 62217 Berichtigung 1:2007 室内外用额定电压大于1000V的聚合绝缘子.一般定义、试验方法和验收标准.技术勘误DIN EN 62217(VDE 0441-1000)-2006-11

Polymeric insulators for indoor and outdoor use with a nominal voltage 1000 V - General definitions, test methods and acceptance criteria (IEC 62217:2005); German version EN 62217:2006, Corrigenda to DIN EN 62217 (VDE 0441-1000):2006-11; German v

JB/T 10583-2006 低压绝缘子瓷件技术条件

本标准规定了低压绝缘子瓷件的技术要求、试验、包装和标志的一般要求。 本标准适用于直流电压低于1000V的或交流电压低于1000V、频率不超过lOOHz的架空电力线路、电气装置和设备上使用的绝缘子瓷件。 本标准不适用于在有破坏瓷及釉的介质（气体或液体）中工作的瓷件。

Technical specifications of porcelain element for low voltage insulators

DL/T 1048-2007 标称电压高于1000V的交流用棒形支柱复合绝缘子.定义、试验方法及验收规则

本标准规定了交流系统中运行的电力设备和装置上的户内和户外复合支柱绝缘子的定义、技术要求、标志和试验分类及检验规则。 本标准适用于标称电压1kV～252kV、频率不超过50Hz的交流系统中运行的电力设备和装置上的户内和户外棒形支柱复合绝缘子(简称绝缘子)。安装地点的海拔高度为1000m及以下，环境温度在-40℃～+40℃之间。 本标准不包含特殊运行条件下选用绝缘子的要求。

Composite post insulators for a.c. with a nominal voltage greater than 1000V.definitions,test methods and acceptance criteria

IEC 36/264/DTS:2007 IEC 60815-1 TS, Ed. 1.0:污染条件用高压绝缘子的选择和尺寸选定.第1部分:定义、信息和一般原理

IEC 60815-1 TS, Ed. 1.0: Selection and dimensioning of high-voltage insulators intended for use in polluted conditions - Part 1: Definitions, information and general principles

IEC 36/266/DTS:2007 IEC 60815-3-TS, Ed. 1.0:污染环境用高压绝缘子的选择和尺寸选定.第2部分:交流电系统用聚合物绝缘子

IEC 60815-3-TS, Ed. 1.0: Selection and dimensioning of high-voltage insulators intended for use in polluted conditions - Part §: Polymer insulators for a.c. systems

DIN EN 62231:2007 交流电压＞1000V并＜245kV变电站用复合固定柱形绝缘子.定义、试验方法和验收标准

Composite station post insulators for substations with a.c. voltages greater than 1 000 V up to 245 kV - Definitions, test methods and acceptance criteria (IEC 62231:2006); German version EN 62231:2006

IEC 36/265/DTS:2007 IEC 60815-2-TS, Ed. 1.0:污染条件用高压绝缘子的选择和尺寸选定.第2部分:交流电系统用陶瓷和玻璃绝缘子

IEC 60815-2-TS, Ed. 1.0: Selection and dimensioning of high-voltage insulators intended for use in polluted conditions - Part 2: Ceramic and glass insulators for a.c. systems

BS EN 62231:2007 交流电压＞1000V且＜245kV变电站用复合固定柱形绝缘子.定义、试验方法和验收标准

This International Standard applies to composite station post insulators consisting of a load bearing cylindrical insulating solid core made of resin impregnated fibres, a housing (outside the insulating solid core) made of elastomer material (e.g. silicone or ethylene-propylene) and end fittings attached to the insulating core. Composite station post insulators covered by this standard are subjected to cantilever, torsion, tension and compression loads. They are intended for substations with a.c. voltages greater than 1 000 V up to 245 kV. The object of this standard is – to define the terms used, – to prescribe test methods, – to prescribe acceptance or failure criteria. This standard does not include requirements dealing with the choice of insulators for specific operating conditions.

Composite station post insulators for substations with a.c. voltages greater than 1 000 V up to 245 kV - Definitions, test methods and acceptance criteria

CSA C22.2 No.198.1-06 UPD 1-2007 压制成型绝缘管

General Instructions for CSA Standards are now called Updates. Please contact CSA Information Products Sales or visit www.ShopCSA.ca for information about the CSA Standards Update Service.

Extruded insulating tubes

JB/T 6466-2006 额定电压1kV（Um=1.2 kV）到10kV（Um=12kV）纸绝缘电力电缆瓷套式终端

本标准规定了额定电压1kV（Um=1.2kV）到10kV（Um=12kV）纸绝缘电力电缆用瓷套式终端的产品标记和代号、技术要求、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于额定电压1kV（Um=1.2kV）至10kV（Um=12kV）纸绝缘电力电缆用瓷套式户内终端和户外终端，使用条件符合IEC 60055-1-1997中22.2和22.3规定。

Porcelain bushing terminations for paper insulation power cables with rated voltages from 1kV(Um=1.2kV) up to 10kV(Um=12kV)