K54 汽轮机及其辅助设备 标准查询与下载

JB/T 3596-2001 射水抽气器 性能试验规程

　　本标准规定了凝汽设备抽除空气和其它不凝结气体的射水抽气器的性能试验方法，用以测定不同工作水压力、温度下，抽吸的干空气流量与吸入侧压力之间的关系，抽气器耗功等。 　　本标准适用于火力发电站汽轮机凝汽设备的抽气器。

Performance test code for water jet air ejectors

ASME PTC 6A-2001 蒸汽涡轮机试验规程.PTC 6的补充

Test Code for Steam Turbines-Appendix to PTC 6.

DL/T 735-2000 大型汽轮发电机定子绕组端部动态特性的测量及评定

Measurement and evaluation of the dynamic characteristic on stator end windings of the large turbo-generator

DL/T 714-2000 汽轮机叶片超声波检验技术导则

Technical guide for the ultrasonic testing of turbine-blades

BS ISO 14661:2000 工业用热涡轮机(蒸气涡轮机、气体膨胀式轮机).一般要求

This International Standard specifies general requirements intended to facilitate the procurement and supply of steam turbines and gas expansion turbines primarily for industrial applications. This International Standard should serve as a basis for any application although, for special applications, supplementary specifications may also be required, for example for general and special purpose industrial steam turbines used in the petroleum and natural gas industries. This International Standard is applicable to axial- and radial-flow industrial-type turbines (steam turbines and gas expansion turbines). It specifies the basic requirements for single-stage and multi-stage impulse or reaction turbines, which are not spared or are in critical service. In addition, this International Standard also specifies some requirements for driven machines, gear units, lubrication and sealing systems, controls, instrumentation and auxiliary units for turbine plants. Exceptions to the requirements laid down in this International Standard may be agreed between the purchaser and supplier. NOTE 1 Which standard is to be applied in the individual case is the decision of the purchaser. For instance, the purchaser of a generator-driving turbine connected to the public network will generally be responsible for complying with the technical requirements of the public network regardless which standard is specified. If the purchaser of a generator-driving turbine is also the operator of the public network or if he/she is the supplier of an independent power producer (IPP), he/she usually specifies the application of IEC 60045-1. NOTE 2 Further standards on industrial steam turbines for the Petroleum and Natural Gas Industries are ISO 10436 and ISO 10437. Information on other relevant International Standards is given in the bibliography. NOTE 3 A bullet ●at the edge of the text indicates that either a decision is required or further information is to be provided by the purchaser. This information should be indicated on the data sheets (see "Introduction'') otherwise it should be stated in the quotation request or in the tender.

Thermal turbines for industrial applications (steam turbines, gas expansion turbines) - General requirements

DL/T 711-1999 汽轮机调节控制系统试验导则

Test guide of steam turbine governing system

ASME PTC 6A-2000 PTC 6的附录A,蒸汽涡轮机用测试规范

Facilitates the calculation and correction of turbine test results by furnishing numerical examples of the procedures outlined in the Test Code for Steam Turbines (PTC 6-1996). The feedwater heating cycles and gland leakoff systems have been simplified by avoiding unnecessarily long or repetitive calculations while still demonstrating the basic principles involved.

Appendix A To PTC 6, the Test Code for Steam Turbines

ANSI/ASME PTC6A-2000 附录A到PTC 6.蒸气轮机用试验代码

Facilitates the calculation and correction of turbine test results by furnishing numerical examples of the procedures outlined in the Test Code for Steam Turbines (PTC 6-1996). The feedwater heating cycles and gland leakoff systems have been simplified by avoiding unnecessarily long or repetitive calculations while still demonstrating the basic principles involved.

Appendix A to PTC 6, the Test Code for Steam Turbines

JB/T 8990-1999 大型汽轮发电机定子端部绕组模态试验分析和固有频率测量方法及评定

本标准规定了大型汽轮发电机定子端部绕组模态试验分析和固有频率的测量方法及评定准则。 本标准适用于额定功率300 MW及以上的额定转速为3000 r/min和3600 r/min的大型汽轮发电机(包括在空冷、双水冷、全氢冷和水氢冷等)定子端部绕组的模态试验分析和固有频率测量及评定。 大型汽轮发电机在制造厂内做型式试验时，应做定子端部绕组模态试验分析。在电厂做固有频率测量时，如果发现多数线棒有接近电磁干扰力频率的固有频率时，也要做模态试验分析。 大型汽轮发电机产品在出厂前、大修后必须做定子端部绕组的固有频率测量。在电厂，有异常情况时(例如，承受突然短路、线圈磨损或者松动等)，都必须做固有频率测量。 300 MW以下的汽轮发电机，根据具体情况决定在大修后是否做固有频率测量。 进口机组也可参照此标准执行。

Model test analyses and natural frequency measurement methods of large turbo - generators on stator end windings and evaluation criteria

JB/T 8188-1999 汽轮机随机设备供应范围

　　本标准规定了汽轮机随机备品、备件的供应范围。 本标准适用于固定式发电用汽轮机和工业汽轮机随机备品、备件的供应范围。

Scope of spare parts supplied by manufacturer with steam turbine

JB/T 8184-1999 汽轮机低压给水加热器 技术条件

　　本标准规定了汽轮机低压给水加热器(简称低加)的性能和制造技术要求。适用于火力发电厂汽轮机回热系统中管侧设计压力不高于 4.5MPa，设计温度不高于 220℃；壳侧设计压力不高于 1.5MPa，设计温度不高于 400℃ 的表面式低压给水加热器，也适用于相同工作条件的其它热交换器。

Specifications for steam turbine low pressure feed water heaters

JB/T 3329-1999 汽轮机旋转零部件 静平衡

　　本标准规定了汽轮机旋转零部件静平衡要求、方法、校验等。 本标准适用于电站、船舶及工业用汽轮机旋转零部件，其外径D与其长度L之比大于5的套装叶轮、联轴器部件、齿轮的静平衡。

Static balancing standard for rotating parts of steam turbines

JB/T 4273-1999 汽轮机转速控制系统.验收试验

　　本标准主要用于电站汽轮机转速控制系统的验收试验。转速控制系统包括调速系统和超速保护系统。对于其它类型汽轮机，也可参照使用。 汽轮机转速控制系统验收试验目的，是验证制造厂保证书所引用的标准。一般，进行这种试验是验证与IEC 60045-1标准要求的符合性。它包括： 　　a)稳态转速调整率(转速不等率); b)稳态局部转速调整率(局部转速不等率); c)空负荷时，相应于同步器上下限的转速范围; 　　d)调速系统的死区(迟缓率); 　　e)调速系统的稳定性; 　　f)在调速系统控制下甩去部分负荷时，转速的最大瞬时升速; 　　g)危急遮断器的整定; 　　h)调速系统失灵下甩去满负荷后的最高瞬时超速。 　　本标准包括的进行试验的选择与其它试验步骤，应由买方于制造厂商定。

Acceptance tests for steam turbine speed control systems

JB/T 4274-1999 汽轮机隔板.挠度试验方法

　　本标准规定了隔板挠度试验装置的要求、试验步骤、试验结果的判定、试验报告的内容等。 本标准适用于冲动式汽轮机的隔板挠度试验。

Deflection test of diaphragms of steam turbines

JB/T 4058-1999 汽轮机清洁度

　　本标准规定了汽轮机零部件非机械加工表面清洁度分级和铸件、冷作焊接件、机械加工零部件、汽轮机油系统和蒸汽系统的清洁度。 本标准适用于汽轮机铸件、冷作焊接件、机械加工零部件、汽轮机油系统和蒸汽系统零部件清洁度的有关要求。

Standard of cleanliness for steam turbines

JB/T 9632-1999 汽轮机主器管和再热器管的弯管 技术条件

　　本标准规定了汽轮机主汽管和再热汽管的弯管要求、质量检查的规则。 本标准适用于所采购的汽轮机主汽管和再热汽管的弯管。 执行本技术条件时，应根据弯管运行时的温度、压力参数、尺寸及弯制工艺方法（中频加热弯）应用相应的条款。

Specifications for bending pipe of steam turbine main and reheat steam piping

JB/T 9633-1999 凝汽器 胶球清洗装置

　　本标准规定了凝汽器胶球清洗装置的参数系列、技术要求、检测及其成套供应范围。 本标准适用于电厂中凝汽器胶球清洗装置。

Condenser cleaning equipments with sponge rubber balls

JB/T 9634-1999 汽轮机 冷油器(管式)尺寸系列和技术条件

　　本标准规定了汽轮机 冷油器（管式）尺寸系列和技术条件。 本标准适用于汽轮机 冷油器（管式）。

Size classification and specifications for tubular oil coolers of steam turbines

JB/T 9635-1999 发电机用汽轮机 型号编制方法

　　本标准规定了发电用汽轮机型号编制方法。 本标准适用于发电用汽轮机的型号编制。

Type classification methods for steam turbines driving generators

JB/T 9636-1999 汽轮机辅机 型号编制方法

　　本标准规定了汽轮机辅机型号编制方法。 本标准适用于汽轮机主要辅机产品的型号编制。

Type classification methods for steam turbine auxiliaries